• 화약ㆍ발파
• /
• 제40권3호
• /
• pp.66-76
• /
• 2022

최근 오래된 산업단지의 해체수요가 증가하고 있으며, 해체된 산업부지를 원래 자연환경으로 복원하는 공사를 진행하고 있다. 본 시공사례는 오래된 산업단지 내의 대형 철골구조물을 해체하기 위해 발파해체공법 중 전도공법을 적용하였다. 철골구조물을 절단하기 위해 금속 제트가 발생하는 장약용기를 사용하였다. 발파구간 중 철골구조물의 두께가 두꺼운 부분은 가스와 산소 불꽃 또는 아크열에 의해 깊은 홈을 파는 방법인 가우징을 적용하여 두께를 조절하였다. 발파해체 결과, 철골구조물은 예측된 방향으로 정확히 전도하였으며, 주변 시설물에 피해 없이 발파해체를 완료하였다.

• Tribology and Lubricants
• /
• 제39권2호
• /
• pp.35-42
• /
• 2023

Bearing is a mechanical component that supports loads and transmits rotation. As the application of high-value-added products such as semiconductors, aviation, and robots have recently become diverse and more precise, an accurate bearing performance prediction and evaluation technology is required. Bearing performance evaluation can be divided into evaluations based on bearing theory and on numerical analysis. An evaluation based on numerical analysis is a technique that has been highlighted because the problems that remained unsolved owing to time problems can be solved through recent developments in computers. However, current studies have the disadvantage of not considering the essential changes over time and bearing rotation. In this study, bearing performance evaluation based on rigid body dynamic analysis considering rotation and load over time is performed. Rigid body dynamic analysis is performed for deep groove ball bearing to calculate the load applied by the ball. The reliability of the analysis is verified by comparing it with the results calculated using bearing theory. In addition, rigid body dynamic analysis is performed for automotive wheel bearings to calculate the contact angle and load applied by the ball for cases where axial load and radial load are applied, respectively. The effect of rotation and load over time is evaluated from these results.

• 대한치과보철학회지
• /
• 제40권3호
• /
• pp.296-305
• /
• 2002

The main disadvantage of cement-retained implant restorations is their difficulty in retrievability. Advocates of cemented implant restorations frequently state that retrievability of the restoration can be maintained if a provisional cement is used. The purpose of this study was to find the optimal properties of provisional luting cements and the surface treatment of abutments in single implant abutment system. 30 prefabricated implant abutments, height 8mm, diameter 6mm, 3-degree taper per side, with light chamfer margins were obtained. Three commercially available provisional luting agents which were all zinc oxide eugenol type ; Cavitec, TempBond and TempBond NE were evaluated. No cement served as the control. TempBond along with vaseline, a kind of petrolatum (2:1 ratio) was also evaluated. Ten out of thirty abutments were randomly selected and abutment surfaces were sandblasted with $50{\mu}m$ aluminum oxide. Another ten abutments were sandblasted with $250{\mu}m$ aluminum oxide. A vertical groove, 1 mm deep and 5mm long was cut in each twenty abutments. Ten of them were sandblasted with $50{\mu}m$ aluminum oxide. The full coverage casting crowns were cemented to the abutments with the designated provisional luting agent. Specimens were stored in distilled water at $37^{\circ}C$ for 24 hours. Each specimen was attached to a universal testing machine. A crosshead speed of 0.5mm/min was used to apply a tensile force to each specimen. Within the limitations of this in vitro study, the following conclusions were drawn: 1. Tensile bond strength of provisional luting cements in no surface treatment decreased with the sequence of TempBond NE, TempBond, Cavitec, TempBond with vaseline, no cement. 2. Tensile bond strength more increased by surface treatment. Sandblasting with $250{\mu}m$ aluminum oxide exhibited the highest tensile bond strength in the abutment cemented with TempBond NE and sandblasting with $50{\mu}m$ aluminum oxide exhibited the highest tensile bond strength in cemented with TempBond. 3. In the aspect of a groove formation, tensile bond strength significantly increased in TempBond with vaseline only and the others had no significant effect on tensile bond strength.

• Animal Systematics, Evolution and Diversity
• /
• 제28권3호
• /
• pp.192-207
• /
• 2012

To supply the morphological and ecological information of oligotrich ciliates in Korea, water samples were seasonally collected in Gwangyang Bay and Jinhae Bay from August, 2010 to February, 2012 and processed by quantitative protargol staining method. As a result, six species belonging to the genus Strombidium Clapar$\grave{e}$de and Lachmann, 1859 are identified: Strombidium emergens Kahl, 1932; S. dalum Lynn et al., 1988; S. epidemum Lynn et al., 1988; S. tressum Lynn et al., 1988; S. bilobum Lynn and Gilron, 1993; S. pollostomum Lynn and Gilron, 1993. These six species were newly reported from Korean coastal waters. Strombidium emergens is a middle sized Strombidium ($20-50{\mu}m$ in length) and has open and deep oral groove to girdle portion. Strombidium dalum is a small sized Strombidium (${\geq}20{\mu}m$ in length), that has torch-like spiral anterior membranelles and an inverted triangles-shaped macronucleus on the posterior pole. The small sized S. epidemum has conspicuous trichites surrounding the girdle portion and ventral membranelles distinctly separated from anterior membranelles. The small sized S. tressum has torch-like spiral and extremely long trichites among the cilia of anterior membranelles. The middle sized S. bilobum has a bilobed macronucleus. Strombidium pollostomum is also a small sized Strombidium but its ventral membranelles are continuously connected with anterior membranelles. The five species except S. emergens occurred frequently over the wide range of water temperatures and salinities.

• 대한정형외과 초음파학회지
• /
• 제1권2호
• /
• pp.128-133
• /
• 2008

신경 압박의 원인은 외부로부터 가해지는 것도 있고, 신체 내부 병리가 발생하여 신경 주행에 따라 발생할 수 있다. 주관절 이하부에서 압박성 신경병증으로 정중 신경, 척골 신경, 요골신경병증이 있다. 정중 신경은 굴곡 지대부위에서 수근관 증후군이 대표적이며, 모든 신경 포착 증후군 가운데 가장 흔하다. 그 외 주관절 부위에서 스트러더스 인대, 상완 이두근 건막, 회내근, 천수지 굴근 기시부 그리고 비정상 근육들에 의한 회내근 증후군과 전 골간 신경 증후군이 있다. 척골 신경은 스트러더스 궁, 내측 상과 후방의 주관, 척수근 굴근 두 기시부 사이의 건막 등에서 눌리는 주관 증후군과, 수근부에서 결절종, 유구골 갈고리 골절 그리고 혈관성으로 오는 척골 관 증후군이 있다. 요골 신경의 심부 분지가 회외근속을 지나면서 만들어지는 부위에서 눌리는 경우 요골 관 증후군이라고 한다. 치료는 초기에는 소염제나 야간부목, 스테로이드 주사와 같은 보존적 치료를 시행할 수 있으며, 이에 호전되지 않을 경우 전기적 검사나 영상 검사에서 이상이 나타나면 수술적 감압술을 시행하여야 한다.

• 한국임상수의학회지
• /
• 제33권6호
• /
• pp.332-339
• /
• 2016

Polycaprolactone (PCL) scaffold have been developed as an alternative to natural donor tissue to repair a large osteochondral defect. The objective of this study is to evaluate efficacy and biocompatibility of bilayer PCL scaffold implanted for osteochondral repair in rabbit. Twenty-two male New Zealand White rabbits were used in this animal experiment. Rabbits were divided into three groups. Experimental surgery was carried out under general anesthesia. Osteochondral defects (5 mm diameter and 5 mm deep) were made in the center of the patellar groove using a 5 mm diameter biopsy punch. In group I (3D plotting) and group II (salt-leaching), the scaffold was implanted using the press-fitted technique into the defect. In control group, after osteochondral defect was created, the defect was left without implant. After four and eight weeks, rabbits were sacrificed and the defects were evaluated by macro -and microscopical methods. There were not found animal death and severe inflammatory evidence during the experimental periods. There were no significant differences between the experimental groups in gross evaluation. However the group I scored significantly higher than group II at 8 weeks in histological evaluation (P < 0.05). The 3-D plotting PCL scaffold was more suitable method for reconstruction of osteochondral defect than a salt-leaching PCL scaffold.

• Tribology and Lubricants
• /
• 제35권2호
• /
• pp.114-122
• /
• 2019

High-speed rotating machinery requires low cost and reliable bearing elements with low friction, stable rotordynamic characteristics, and a simple design. This study experimentally evaluates the effects of bearing-support elements on the vibrational characteristics of a small-sized, high-speed permanent magnetic motor. A series of coast down tests from 100 krpm characterize the vibrational behaviors, rotor displacement, and housing acceleration of motors supported by ball bearings, ball bearings with a metal mesh damper, and gas foil bearings, respectively. Two eddy-current sensors installed in the horizontal and vertical directions measure the displacement of the rotor at its front nut, and a 3-axis accelerometer attached to the motor housing measures the housing acceleration. The test results reveal that synchronous (1X) vibration components most significantly affect the rotor displacement and housing acceleration, independent of the bearing-support elements. The motor supported by the deep-groove ball bearings results in the largest rotor vibrations increasing with speed; this is due to the absence of a damping mechanism. Additionally, the metal mesh damper effectively reduces the rotor displacement, housing acceleration, and sound-pressure level in the high-speed region (i.e., above 40 krpm), thus implying its substantial damping performance when installed on the outer race of the ball bearing. Lastly, the gas foil bearing supported motor yields the smallest rotor displacement, housing acceleration, and lowest sound-pressure level because of its hydrodynamic airborne operation, which does not require rolling elements that may cause mechanical friction and vibrations.

• 한국정보통신학회논문지
• /
• 제24권1호
• /
• pp.100-106
• /
• 2020

본 논문에서는 저전력장거리 기술과 임베디드 보드를 이용한 치매 돌봄 스마트 신발과 응용 소프트웨어를 구현하였다. Cortex-M3 보드와 로라 모듈로 구성된 통신 모듈은 신발 밑창의 홈에 내장 된다. 위치추적 응용 소프트웨어는 임베디드 보드에서 제공하는 신호와 GPS와 로라 망을 이용하여 보호자가 치매 환자의 위치 추적할 수 있다. 외부 환경에서 스마트 신발의 위치 추적 및 데이터 전송 동작이 성공적으로 확인되었다. 이러한 실험을 통해 본 논문에서 개발한 스마트 신발이 치매 환자의 돌봄을 위한 실종을 막는 안전장치로 응용 가능할 것으로 판단된다.

• Tribology and Lubricants
• /
• 제39권1호
• /
• pp.1-7
• /
• 2023

Fluid pumps in chemical processes are typically driven by electric motors. Even if the motor is separated from the pump with seals, wear resulting from friction and misalignment can lead to leakage of chemical fluid, causing corrosion in the bearing supporting the motor, and, eventually, failure of the motor. It is thus a standard procedure to replace bearings at regular intervals. In this article, we propose 3D-printed plastic ball bearings for use as an alternative to commercial stainless-steel ball bearings. The plastic bearings are easy to manufacture, require less time to replace, and are chemically resistant. To validate the applicability of the plastic bearings, we first conducted chemical resistance tests. Bearings were immersed in 30 caustic acid and 30 nitric acid for 30 min and 24 h, respectively. The test results showed no corrosive damage to the bearings. A test rig was set up to compare the performance of the plastic bearings with that of the commercially equivalent deep-groove ball bearings. Loading test results showed that the plastic bearings performed as well as the commercial bearing in terms of vibration level and load-handling capability. Finally, a plastic bearing was subjected to a clean-in-place process for three months. It actually outperformed the commercial bearing in terms of chemical resistance. Thus, 3D-printed plastic bearings are a viable alternative to stainless-steel ball bearings.

• 대한치과보존학회:학술대회논문집
• /
• 대한치과보존학회 2001년도 춘계학술대회
• /
• pp.247-251
• /
• 2001

;A dental developmental anomaly is defined as an isolated aberration in tooth form, caused by a disturbance or abnormality which occurred during tooth development. There are numerous types of dental anomalies, and a considerable variation in the extent of the defects occurs with each type. Teeth with these anomalies pose unique challenges. Since the defects are not always apparent clinically, they can confuse diagnosticians investigating the etiology of pulpal pathosis. When endodontic treatment is required, the defects often hinder access cavity preparation and canal instrumentation. Treatment planning also becomes more challenging, since the defects can create complicated periodontal problems, and the malformed teeth can be difficult to restore, particularly those weakened by endodontic therapy. Fusion is defined as the joining of two developing tooth germs resulting in a single large tooth structure. The incidence of fusion is < 1% in the Caucasian population, and it is believed that physical force or pressure produces contact of the developing teeth. Clinically and radiographically, a fused tooth usually appears as one large crown with at least partially separated roots and root canals. There may be a vertical groove in the tooth crown delineating the originally separate crowns. Dens invaginatus is a deep surface invagination of the crown or root that is lined by enamel. Teeth in both maxillary and mandibular arches may be affected, but the permanent maxillary lateral incisor is the tooth most commonly involved. Studies have revealed an incidence ranging from 0.25% to as high as 10%. The invagination ranges from a slight pitting to an anomaly occupying most of the crown and root. The invagination frequently communicates with the oral cavity, allowing the entry of irritants and microorganism either directly into pulpal tissues or into an area that is deparated from pulpal tissues by only a thin layer of enamel and dentin. This continuous ingress of irritants and the subsequent inflammation usually lead to necrosis of the adjacent pulp tissue and then to periapical or periodontal abscesses. If the invagination extends from the crown to the periradicular tissue and has no communication with the root canal system, the pulp may remain vital. Recommended treatment of fused tooth and dens invaginatus has been reported in the endodontic literature. This case report describes the endodontic treatment of a maxillary laterl incisors having fused crown and dens invaginatus.natus.