• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.463-468
• /
• 2002

For the Externally bonded FRP systems, flexural design method is studied focusing on the reinforcement layer of the carbon fiber sheets. As the FRP layer is added, strengthening rate increases, but not proportionally as the FRP layer increases. This is reflected in the design formula appropriately by the bond cofficients from the added layers. As the number of FRP layer increases, the stress reinforcement and FRP sheet decreases, and it generally corresponds to the decrease rate of member flexural strength. This phenomenon is appearing indentically in a design formula and experimental result. The rate of $M_{test}$ and $M_n$ is 1.19 and it is estimated as safety factor which is the reduction factor, ${\psi}_f = 0.85$.

• Structural Engineering and Mechanics
• /
• v.73 no.6
• /
• pp.631-640
• /
• 2020

Using backup plate is one of the most commonly used methods to decrease drilling-induced delamination of composite laminates. It has been shown that, the size of the delamination zone is related to the vertical element of cutting force named as thrust force. Also, direct control of thrust force is not a routine task, because, it depends on both drilling parameters and mechanical properties of the composite laminate. In this research, critical feed rate and thrust force are predicted analytically for delamination initiation in drilling of composite laminates with backup plate. Three common theories, linear elastic fracture mechanics, classical laminated plate and mechanics of oblique cutting, are used to model the problem. Based on the proposed analytical model, the effect of drill radius, chisel edge size, and backup plate size on the critical thrust force and feed rate are investigated. Experimental tests were carried out to prove analytical model.

• Journal of Environmental Science International
• /
• v.3 no.3
• /
• pp.263-271
• /
• 1994

A detachment of biofilm was investigated in an inverse fluidized bed biofilm reactor(IFRBR). The biofilm thickness, 5 and the bioparticle density, Pm were decreased by the increase of Reynolds number, Re and the decrease of biomass concentration, h. The correlations were expressed as $\delta$=6l.6+16.33$b_c$-0.004Re and Ppd=0.3+0.027$b_c$- 2.93x$l0^{-5}$ no by multiple linear regression analysis method. Specific substrate removal rate, q was derived by F/M ratio and biofilm thickness as q=0.44.+0.82F/M-5.Ix10$-4^{$\delta$}$. Specific biofilm detachment rate, bds was influenced by FIM ratio and Reynolds number as $b_{ds}$=-0.26+0.26F/M+ 2.17$\times$$10^{-4}$Re. Specific biofilm deachment rate in an IFBBR was higher than that in a FBRR(fluidized bed biofilm reactor) because of the friction between air bubble and the bioparticles.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.35 no.4
• /
• pp.410-420
• /
• 1999

The value of the mode I interlamina fracture toughness, GIC, is calculated by experimental compliance method, modified compliance method and beam theory. The value of the mode II interlamina fracture toughness, GIC, is evaluated by beam method, theory beam theory and compliance method. This paper describes the effect of load pint displacement rate and speicimen geometries for mode I and II interlaminar fracture toughness of glass fiber reinforced plastic composites by using double cantilever beam (DCB) and end notched flexure (ENF) specimen. For the load point displacement rate of increases whereas the value of 2,6 and 10 mm/min the value of GIC decrease as load point displacement rate increases whereas the value of GIC is found to be no significant effect. The value of GIC decreases as initial crack length increases. The fractured surface of the DCB and ENF samples are examined by scanning electron microscopy (SEM).

• Journal of the military operations research society of Korea
• /
• v.30 no.1
• /
• pp.135-152
• /
• 2004

Ever since Benoit's(1973, 1978) study, the relationship between defense spending and economic growth has been the subject of extensive empirical works. While a number of studies have reported that higher defense expenditure stimulate economic growth, many other studies have reported that an increase in military burden may hinder economic growth. To the extent that countries differ substantially in socioeconomic structures, the effects of defense spending cannot be generalized across countries. In this paper, Granger causality tests are performed between Korean defense expenditure and economic growth, consumption, investment, inflation and unemployment rate during the period from 1970 to 2002. The results show that Korean defense expenditure did not affect economic growth and unemployment rate. However, Korean defense expenditure caused consumption and inflation to decrease and investment to increase. On the other hand Korean defense expenditure was not Granger-caused by economic growth, consumption, investment, inflation and unemployment rate. In conclusion, the opportunity cost of Korean defense expenditure seemed to be relatively moderate considering Korean security environment. Even if it was not statistically significant, Korean defense burden at least did not bother economic growth.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.39 no.2
• /
• pp.26-31
• /
• 1997

Abstract A series of permeability tests was performed on the mixtures with specific mixing rates of sand and bentonite using modified rigid-wall permeameter. Sand-bentonite mixtures were permeated by organics, ethanol and TCE. Permeability of bentonite with several mixing rates had a tendency to decrease up to initial one pore volume and permeability was thereafter converged to a constant value. When sand-bentonite mixtures was permeated by water, permeability was decreased at the beginning but it was thereafter converged to a constant. Among several mixing rates, permeability was greatly decreased at 15% of mixing rate. When sand-bentonite mixtures with 15% mixing rate was permeated by ethanol, permeability was about 10 times larger value than permeability of water. Peameability was shown greater values when permeated by TCE (TrichloroEthylene) followed by ethanol. Suitable mixing rate of sand-bentonite for a liner of waste landfills was detected.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.39 no.2
• /
• pp.32-43
• /
• 1997

Abstract A series of permeability tests was performed on the mixtures with specific mixing rates of sand and bentonite using modified rigid-wall permeameter. Sand-bentonite mixtures were permeated by organics, ethanol and TCE. Permeability of bentonite with several mixing rates had a tendency to decrease up to initial one pore volume and permeability was thereafter converged to a constant value. When sand-bentonite mixtures was permeated by water, permeability was decreased at the beginning but it was thereafter converged to a constant. Among several mixing rates, permeability was greatly decreased at 15% of mixing rate. When sand-bentonite mixtures with 15% mixing rate was permeated by ethanol, permeability was about 10 times larger value than permeability of water. Peameability was shown greater values when permeated by TCE (TrichloroEthylene) followed by ethanol. Suitable mixing rate of sand-bentonite for a liner of waste landfills was detected.

• Journal of Environmental Science International
• /
• v.7 no.1
• /
• pp.74-80
• /
• 1998

Because permeate flux was very low as It has the suspension soled of higher concentration In the trafiltration membrane separation treatment of dyestuff wastewater, pre-treatment of Ponton reaction was carried out. In the case of pH 3, COD removal rate was the hi각erst of 58%. When PAC was added into the pre-treatment supernatant, the COD removal rate was found to be 53% , and when COD was 153mg/L, the removal rate was 92.3% in the trafiltration separation. In addition, the effect of the addition of PAC on the permeate flux was also investigated. The decrease of permeate flux In the presence of PAC was higher than In the abscence of PAC, but the recovery of permeability by cleaning was better In the case of PAC system.

• Journal of the Korean Society of Combustion
• /
• v.16 no.3
• /
• pp.1-11
• /
• 2011

The main objective of this paper is to investigate characteristic of steam reformer at various geometries and operating conditions. In this paper, the steam reforming is studied by a numerical method and three dimensional simulations were used for effective analytical study. User - Defined Function (UDF) was used to simultaneously calculate reforming and combustion reaction. And the numerical model is validated with experimental results at the same operating conditions. In order to understand the relationship between operating conditions such as gas hourly space velocity(GHSV), mass flow rate of combustor inlet, various numerical investigations are carries out for various geometries. Numerical results show that cylindrical geometry is more effective than rectangular geometry for heat transfer to reactors and reforming efficiency. As mass flow rate of combustor inlet increase, reaction occurs more faster and temperature increase with each geometry. On the other hand, reaction and hydrogen conversion decrease as mass flow rate of reactor decreases.

• The Science & Technology
• /
• v.8 no.3 s.70
• /
• pp.31-39
• /
• 1975

SUMMERY 1. The length of trypanosoma can be shown 17-25μ on the korean dairy cattles. 2. Crjthida of trypanosoma was is found out in depresed Tabanid flies head and about 60% in Tabanid flies head. 3. Trypanosoma in the tryptose blood agar base was variated afrer about 6 weeks. 4. Infectional rate of trypanosoma is same tate about 52%. 5. Mild production in multltlic infected dairy cattles is delow thbn non inflected daily cattes. and fat rate is about 3.1% in Holstein. 6. Injected trypanosoma rate in summer is higher than in winter about 10%. 7. Calfs in winter wasnot infected for trypanosoma. 8. Erythrocyte number decrease and Leucocyte number increase in a lot of infected trypanosoma of dairy cattles. 9. There is degeneration is genital organs. endocrine gland.