• 한국초지조사료학회지
• /
• 제38권1호
• /
• pp.7-15
• /
• 2018

본 연구는 혐기소화발효액을 배지로 이용하여 클로렐라를 배양한 배양액이 페레니얼라이그라스 종자 발아에 미치는 영향을 구명하기 위하여 혐기소화발효액, 클로렐라 배양액, 클로렐라 배양여액, 혐기소화발효액, 무처리구(물)을 처리하여 종자 발아시험을 수행하였다. 페레니얼 라이그라스 종자의 최종 발아율은 무처리구의 70.2%와 비교하여 클로렐라 배양액 처리구가 91.9%로 21.2% 높았다. 또한 상대발아율도 클로렐라 배양액 처리구가 클로렐라 배양액을 처리하지 않은 무처리구(물) 보다 25% 높았다. 페레니얼 라이그라스 종자의 50% 발아에 소요되는 일수(T50)는 클로렐라 배양액 3.3~3.5일로 무처리구의 4.7~5.1일보다 빨랐다. 페레니얼 라이그라스 종자의 뿌리길이는 클로렐라 배양액 처리구가 무처리(물)보다 1~2cm이상 길었다. 상대적 뿌리신장율은 클로렐라 배양액 처리구의 무처리구보다 40% 높았다. 페레니얼 라이그라스 종자의 발아지수(GI)는 클로렐라 배양액 처리구가 182로 무처리구(물)의 100 보다 높았다. 종자의 부패율은 치상 후 11일째에 무처리구와 혐기소화발효액 처리구가 각각 83.3, 86.7%으로 높았으나 클로렐라 배양액 처리구는 50.0%로, 클로렐라 배양여액 처리구가 53.3%로 부패율이 낮았다. 클로렐라 배양액, 클로렐라 배양여액 처리가 종자의 부패방지 효과를 나타내었다.

• 대한기계학회논문집B
• /
• 제20권12호
• /
• pp.4013-4026
• /
• 1996

A numerical simulation has been carried out for the jet impinging on a flat plate and a semi-circular concave surface. In this computation finite volume method was employed to solve the full Navier-Stokes equation based on a non-orthogonal coordinate with non staggered variable arrangement. The standard k-.epsilon. turbulent model and low Reynolds number k-.epsilon. model(Launder-Sharmar model) with Yap's correction were adapted. The accuracy of the numerical calculations were compared with various experimental data reported in the literature and showed good predictions of centerline velocity decay, wall pressure distribution and skin friction. For the jet impingement on a semi-circular concave surface, potential core length was calculated for two different nozzle(round edged nozzle and rectangular edged nozzle) to consider effects of the nozzle shape. The result showed that round edged nozzle had longer potential core length than rectangular edged nozzle for the same condition. Heat transfer rate along the concave surface with constant heat flux was calculated for various nozzle exit to surface distance(H/B) in the condition of same jet velocity. The maximum local Nusselt number at the stagnation point occurred at H/B = 8 where the centerline turbulent intensity had maximum value. The predicted Nusselt number showed good agreement with the experimental data at the stagnation point. However heat transfer predictions along the downstream were underestimated. This results suggest that the improved turbulence modeling is required.

• 수산해양기술연구
• /
• 제55권4호
• /
• pp.310-319
• /
• 2019

Although mud shrimp (Upogebia Major) provides benefits on the tidal flat ecosystem, it is causing the mass mortality of Manila clam (Tapes philippinarum) and large economic loss to the aquaculture farmer due to spreading in the entire coastal clam farm area of the West Sea of Korea. In this study, a mud shrimp blocking box for cultivating clam was tested to prevent the mud shrimp from invading the habitat of the clam. To determine the effect of the blocking box, the growth characteristics of the clams under various culture conditions were investigated. The shell length, total weight, condition index, the presence of mud shrimp in the box, and the soil decay in the box were examined according to whether the clams were raised in the box or in natural state, whether the box is covered with a net or not and the gap size of the box. As a result, no significant differences in shell length, total weight, and condition index were found between the clam grown in the box and the natural state (P>0.05) without any evidence of invading of mud shrimp to the box. In addition, the soil inside the box was in good condition, not decayed. Therefore, using the mud shrimp blocking box, mud shrimp can be prevented from propagating to the habitat of the clam, thereby contributing to the normal production of the clam and thus to restoring the clam farming.

• Nuclear Engineering and Technology
• /
• 제52권9호
• /
• pp.1963-1973
• /
• 2020

Liquid metal-cooled reactors use various passive safety systems driven by natural circulation. Investigating these safety systems experimentally is more advantageous by using a simulant. Although numerous experimental approaches have been applied to natural circulation-driven passive safety systems using simulants, there has been no clear validation of the similarity law. To validate the similarity law experimentally, SINCRO-V experiment was conducted using Wood's metal and water for simulant of the Wood's metal. A pair of SINCRO-V facilities with length-scale ratio of 14.1:1 for identical Bo' was investigated, which was the main similarity parameter in temperature field simulation. In the experimental range of 0.2-1.0% of decay heat, the temperature distribution characteristics of the small water facility were very similar to that of the large Wood's metal facility. The temperature of the Wood's metal predicted by the water experiment showed good agreement with the actual Wood's metal temperature. Despite some error factors like discordance of Gr' and property change along the temperature, the water experiment predicted the Wood's metal temperature with an error of 27%. The validity of the similarity law was confirmed by the SINCRO-V experiments.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제26회 춘계학술대회논문집
• /
• pp.73-76
• /
• 2006

액체 로켓엔진에서의 고주파 연소불안정 제어를 위한 수동 안정화 제어 기구로 음향공을 적용하여 감쇠 효과의 적합성을 검증하였다. 음향공의 기하학적 형상에 따른 음향 감쇠 효과를 비교하기 위하여, 주요 설계 변수를 변화시킨 음향공 모델에 대해 유해 공진주파수 감쇠 효과를 정량적으로 비교, 분석하였다. 선형음향해석과 실험적 방법 모두 만족할만한 일치성을 나타내었으며, 오리피스 입구 면적이 가장 크거나 오리피스 길이가 가장 짧은 경우에서 감쇠 효과가 가장 크게 나타났다. 결론적으로 음향공을 이용한 최적의 음향공 제어를 위해서는 음향공 부피를 고려한 최적기 음향공 설계가 절대적으로 필요함을 입증한다.

• International Journal of Concrete Structures and Materials
• /
• 제10권3호
• /
• pp.393-406
• /
• 2016

Axially loaded reinforced concrete columns are hardly exist in practice due to the development of some bending moments. These moments could be produced by gravity loads or the lateral loads. First, the current paper presents a detailed analysis on the overall structural behavior of 15 eccentrically loaded columns as well as one concentrically loaded control one. Columns bent in either single curvature or double curvature modes are tested experimentally up to failure under the effect of different end eccentricities combinations. Three end eccentricities ratio were studied, namely, 0.1b, 0.3b and 0.5b, where b is the column width. Second, an expression correlated the decay in the normalized axial capacity of the column and the acting end eccentricities was developed based on the experimental results and then verified against the available formula. Third, based on the equivalent column concept, the equivalent pin-ended columns were obtained for columns bent in either single or double curvature modes. And then, the effect of end eccentricity ratio was correlated to the equivalent column length. Finally, a simplified design procedure was proposed for eccentrically loaded braced column by transferring it to an equivalent axially loaded pin-ended slender column. The results of the proposed design procedure showed comparable results against the results of the ACI 318-14 code.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2003년도 하계학술연구발표회 및 한.일 공동심포지엄
• /
• pp.21-21
• /
• 2003

Microstructure and magnetic transport phenomina in rf sputtered AlN/Co type ten-layered discontinuous films of nanoscaled [AlN (3 nm)/Co (t nm)]...$\sub$10/ with t$\sub$Co/=1.0∼2.0 nm have been investigated. The microstructure and tunneling magnetic resistance of the samples are strongly dependent on the thickness of Co layer. Negative tunneling magneto-resistance due to the spin-dependent transport has been observed along the current-in-plane configuration in the samples having the Co layers below 1.6 nm thick. When the thickness of Co layer was less than 1,2 nm, randomly oriented granular Co particles were completely isolated and embedded in amorphous AlN matrix, and the films showed the superparamagnetic behavior with a high MR value of Δ$\rho$/$\rho$$\sub$0/=1.8 %. As t$\sub$Co/ increases, a transition from the regime of co-existence of superparamagnetic and ferromagnetic behaviors to ferromagnetic behavior was observed. Tunneling barrier called "decay length for tunneling" for the films having the thickness of Co layer from 1.4 to 1.6 nm was measured to be ranged from 0.004 to 0.021 ${\AA}$$\^$-1/.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1996년도 International Conference on Agricultural Machinery Engineering Proceedings
• /
• pp.852-862
• /
• 1996

This study was carried out to develop tools to detect defects of apple using machine vision. For the purpose, 6 kinds of frame for color images, R, G, B, h, S, and I frame, and a frame for near infra-red images (NIR frame) were tested first to select one which is useful to segment defect areas from apple images. After then, several methods to classify kind of defect for the segmented defect areas were developed and tested. Five kinds of apple defect -bruise , decay ,fleck worm hole and scar were investigated . The results are as follows: NIR frame was selected as the best one among the 7 kinds of image frame, and R, G and I frames showed favourable result to segment areas of apple defect. Various features of the segmented defect areas were measured to classify the defect areas. Eight kids of feature of the areas-size, roundness, axes length ratio, mean and variance of pixel values, variance of real part of spectrum, mean and variance of power spectrum resulted from spacial ourier transform were observed for the segmented defect areas in the selected 4 frames. then procedures to classify defects using the features were developed for the 4 frames and tested with 75-113 defects on apples. The test resulted that NIR and I frames showed high accuracies to classify the kind of defect as 77% and 76% , respectively.

• Journal of Magnetics
• /
• 제8권2호
• /
• pp.98-102
• /
• 2003

Microstructure and magnetic transport phenomina in rf sputtered AIN/CO type ten- layered discontinuous films of nanoscaled [AIN(3 nm)/Co(t nm)]…$_10$ with t$_Co$=1.0∼2.0 nm have been investigated. The microstructure and tunneling magnetic resistance of the samples are strongly dependent on the thickness of Co layer, Negative tunneling magneto-resistance due to the spin-dependent transport has been observed along the current-in-plane configuration in the samples having the Co layers below 1.6 nm thick. When the thickness of Co layer was less than 1.2 nm, randomly oriented granular Co particles were completely isolated and embedded in amorphous AIN matrix, and the films showed the superparamagnetic behavior with a high MR value of ${\Delta}p/p_0$=1.8%. As t$_Co$ increases, a transition from the regime of co-existence of superparamagnetic and ferromagnetic behaviors to ferromagnetic behavior was observed. funneling barrier called “decay length far tunneling” fur the films haying the thickness of Co layer from 1.4 to 1.6 nm was measured to be ranged from 0.004 to 0.021 ${\AA}$$^{-1}$.

• 한국광학회지
• /
• 제12권4호
• /
• pp.300-304
• /
• 2001

압전소자에 전압을 가했을 때 길이가 늘어나며 휘어지는 것을 측정하고 보정하는 방법을 제시한다. 압전소자에 부착된 거울에서 반사되는 레이저빔의 각도 변화를 $0.36\mu$rad의 불확도로 측정하여 압전소자가 휘는 각도와 방향을 알수 있는 장치를 구성하였다. 압전소자의 전극을 세부분을 분할하고 축전기를 직렬 연결하여 하나의 전원으로도 각 전극에 인가되는 전압을 달리 조절할 수 있었다. 압전소자가 휘어지는 크기와 방향에 따라 각 전극에 연결되는 축전기의 용량을 달리함으로써 보정 전에 비해 휨을 6.3%로 줄일수 있었다. 휨이 보정된 압전소를 광자감쇠공동의 길이 변조에 이용하였을 때 압전소자가 휘기 때문에 야기되었던 감쇠시간 요동이 효과적으로 제거되는 것을 확인하였다.