• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.267-274
• /
• 2004

The optimum condition is defined as one that best suits the purpose of flocculation; the number of small particles should decrease, while that of large particles should increase. The object of this research was to develop a new impeller and substitute for conventional flocculators. The flow characteristics of turbines and hydrofoil type flocculators in turbulent fluids were observed using a standard k-$\epsilon$ Model and a computational fluid dynamics (CFD) simulation program- FLUENT The experiments were performed to compare PBT(Pitched Blade Turbine) flocculator with twisted hydrofoil type flocculators for velocity distribution, and floc formation at conventional water treatment plants in Korea. As a result of the CFD solution, twisted hydrofoil types are similar to hydrofoil flocculators for flow characteristics without regard to the twisted angle, On the other hand, it was established that turbine flocculators are greater than hydrofoil flocculators with flow unevenness and dead zone formation. Twisted hydrofoil type- II (Angle $15{\~}20^{\circ}$) is the most proper impeller for water flocculation from this point of view with a decreasing the dead zone, maintaining of the equivalent energy distribution and a drawing up of the sedimentation substance from the bottom of the flocculation basin.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.10C
• /
• pp.987-992
• /
• 2002

In this paper, a new clock and data recovery circuit is proposed for the application of data communication systems requiring ㎓-range clock signals. The circuit is suitable for recovering NRZ data which is widely used for high speed data transmission in ㎓ ranges. The high frequency jitter is one of major performance-limiting factors in PLL, particularly when NRZ data patterns are used. A novel phase detector is able to suppress this noise, and stable clock generation is achieved. Futhermore, the phase detector has an adaptive delay cell removing the dead zone problem and has the optimal characteristics for fast locking. The proposed circuit has a convenience structure that can be easily extended to multi-channels. The circuit is designed based on CMOS 0.25㎛ fabrication process and verified by measurement result.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.5
• /
• pp.1978-1985
• /
• 2018

In this paper, a novel single-phase hybrid switched reluctance motor (HSRM) is proposed for hammer breaker application. The hammer breaker requires only unidirectional rotation and high-speed operation. To satisfy the requirements and eliminate torque dead-zone, the rotor of the proposed 4/4 poles SRM is designed with wider pole arc and non-uniform air-gap. This motor has a simple structure and produces low torque ripple. Permanent magnets (PMs) are mounted on the inner stator at a certain position which enables it to park the rotor for self-start and create positive cogging torque in the torque dead-zone. Compared with conventional single-phase switched reluctance motor, HSRM has an increased torque density and relatively low torque ripple. To verify effectiveness, finite element method (FEM) is employed to analyze the performance of the proposed structure. Then, the proposed motor is compared with the existing motor drive system for the same application. The proposed HSRM is easy to manufacture along with competitive performance.

• Transactions of Materials Processing
• /
• v.13 no.6 s.70
• /
• pp.540-545
• /
• 2004

Ever since the ideal forming theory has been developed for process design purposes, application has been limited to sheet forming and, fur bulk forming, to two-dimensional steady flow. Here, application for the non-steady case was performed under the plane-strain condition based on the theory previously developed. In the ideal flow, material elements deform following the minimum plastic work path (or mostly proportional true strain path) so that the ideal plane-stram flow can be effectively described using the two-dimensional orthogonal convective coordinate system. Besides kinematics, fur a prescribed final part shape, schemes to optimize a preform shape out of a class of initial configurations and also to define the evolution of shapes and boundary tractions were developed. Discussions include the two problematic issues on internal tractions and the non-monotonous straining. For demonstration purposes, numerical calculations were made for a bulk part under forging.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.8C
• /
• pp.721-730
• /
• 2012

In this paper the problem of a moving control of an automatic guided vehicle(AGV) which transports a dead body to a designated cinerator safely in a crematorium, an special indoor environment, will be discussed. Since a method of burying guided lines in the floor is not proper to such an environment, a method of moving control of an AGV based on infrared ray sensors is now proposed. With this approach, the AGV emits infrared ray to the landmarks adheres to the ceiling to find a moving direction and then moves that direction by recognizing them. One of the typical problems for this method is that dead zone and/or overlapping zone may exist when the landmarks are deployed. To resolve this problem, an algorithm of recognizing double landmarks at each time is applied to minimize occurrences of sensing error. In addition, at the turning area to entering the designated cinerator, to fit an AGV with the entrance of the designated cinerator, an algorithm of controlling the velocity of both the inner and outer wheel of it. The functional correctness of our proposed algorithm has been verified by using a prototype vehicle. Our real AGV system has been applied to a crematorium and it moves automatically within an allowable range of location error.

• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1661-1668
• /
• 2016

A fixed off-time controlled high power factor ac-dc LED driver is proposed in this paper, which employs a novel zero-crossing-compensation (ZCC) circuit based on a fixed off-time controlled scheme. Due to the parasitic parameters of the system, the practical waveforms have a dead region. By detecting the zero-crossing boundary, the proposed ZCC circuit compensates the control signal VCOMP within the dead region, and is invalid above this region. With further optimization of the parameters KR and Kτ of the ZCC circuit, the dead zone can be eliminated and lower THD is achieved. Finally, the chip is implemented in HHNEC 0.5μm 5V/40V HVCMOS process, and a prototype circuit, delivering 7~12W of power to several 3-W LED loads, is tested under AC input voltage ranging from 85V to 265V. The test results indicate that the average total harmonic distortion (THD) of the entire system is approximately 10%, with a minimum of 5.5%, and that the power factor is above 0.955, with a maximum of 0.999.

• Korean Journal of Environment and Ecology
• /
• v.29 no.1
• /
• pp.81-87
• /
• 2015

This study was carried out in the peatland for estimating the paleoenvironment based on the analysis from its fossils plant and radiocarbon at the Hwayang-ri, Hyeondeok-myeon, Pyeongtaek-city, South Korea. Variety of fossil was collected from the peatland which could discriminated with naked eye and sorted into seeds, leaves, stems from four-stage of standard sieve. During analysis for the large plant fossil within the peatland, the dead plants were largely divided into 3 fossil zones according to its peatland. In the fossil zone III (the oldest layer; 6,970~6,070 yr $C^{14}$ B.P.), the observation of leaves of hydrophyte such as Trapa sp. and stems of Alnus japonica which appeared in wetland means that the environment was influenced by the climate changes such as rainfall increasing and sea level rise. In the fossil zone II (the middle layer; 6,070~5,800 yr C14 B.P.), the occurrence of Gramineae, Cyperaceae and Fagaceae indicate that the environmental condition might be more or less dry by decreasing rainfall and drop in sea level. The fossil zone I (the recent layer; 5,800~4,540 yr $C^{14}$ B.P.) where lots of herbaceous plants, increasing of Fagaceae, decreasing of A. japonica. and distribution of Pinaceae were showed, was inferred to be repeated both dry and wet environment due to human disturbance.

• Ocean and Polar Research
• /
• v.42 no.3
• /
• pp.233-247
• /
• 2020

This study was carried out at 5 sites 11 times over two years to identify the variation of benthic environments and benthic polychaetous community and analyze the benthic healthiness in Dangdong Bay, a small semi-enclosed inner bay of Jinhae Bay. The temperature of bottom water showed the typical temporal fluctuation of a temperate zone and was in the range of 5.94 ~ 23.94℃. The salinity did not change significantly during the study period and was in the range of 32.93 ~ 35.72 psu. The concentration of dissolved oxygen of bottom water fluctuated a great deal and was in the range of 0.31 ~ 10.20 mg/L. The lowest DO value was recorded in July 2015, as 0.31±0.04 mg/L corresponding to the hypoxic water mass. The hypoxic water mass was formed continuously at some sites also in July and August 2016. The mean grain size was in the range of 7.57 ~ 9.81Ø and the average was 8.89±0.20Ø. The surface sediments were mainly composed of fine sediment (mud) above 85%. The mean of TOC was 3.09±0.22% and LOI was 13.30±0.47%, showing very high levels in Korean coastal waters. The concentration of AVS was in the range of 0.33 ~ 1.28 mgS/g-dry. The high values of organic contents and AVS indicated that there had been the serious organic enrichment in Dangdong Bay. The number of species and the density of the benthic polychaetous community in Dangdong Bay were in the range of 2 ~ 38 species and 2 ~ 2,185 ind./㎡ during the study period. The number of species and density were highly sustained in winter and spring, and then decreased gradually with the formation of a hypoxic water mass in summer, and the lowest number of species and density were recorded in autumn. In September and November 2015, the dead zone expanded to almost the whole study area. Dominant polychaetous species were Capitella capitata, Lumbrineris longifolia, Paraprionospio patiens and Sigambra tentaculata, each known as opportunistic species and potential organic pollutant indicator species. In particular, Paraprionospio patiens showed a very high population density of 2,019 ind./㎡ in December 2016. Polychaetous communities at each sampling time were classified into 4 temporal groups according to dominant species in each period by cluster analysis and nMDS. 'Period Group AI' was formed in winter and spring of 2015, dominated by Capitella capitata, 'Period AII' in summer dominated by Lumbrineris longifolia, 'Period B' in autumn with no fauna in the dead zone, and particularly 'Period C' in winter of 2016 dominated by Paraprionospio patiens. As a result of analysis of benthic healthiness, the study area was estimated to be in a Fair~Very Poor condition by AMBI and in a Poor~Very Poor condition by BPI during the study period. Both AMBI and BPI showed that the study area was in a Very Poor condition in September and November 2015, and when the dead zone occurred. In Dongdong Bay, the fact that the formation of a hypoxic water mass occurred in summer and a dead zone in autumn were confirmed. In addition, the dominance of opportunistic and organic pollutant indicator species was also observed clearly. The benthic healthiness indexes such as AMBI and BPI showed that organic enrichment was serious in Dangdong Bay.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1994.03a
• /
• pp.175-182
• /
• 1994

Effect of some process variables including area reduction, stroke advance, materials on the extrusion load, plastic flow and height ratio of upper to lower extruded parts in the cup-cup axisymmetric extrusion were experimentally investigated and analyzed. Deformed pattern is visualized by grid-marking technique using half-cut billets splitted. The influence of using split specimen and original specimen on the extrusion load and height ratio is examined by experiment.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.889-894
• /
• 1993

This paper presents a robust adaptive control scheme based on the Lyapunov design for robot manipulators subjected to inertial parameter uncertainties and bounded torque disturbances. The scheme is a modified version of the adaptive computed torque method which adopts a dead zone into the adaptation mechanism so as to avoid parameter drifts by disturbances. It is shown via stability analysis and computer simulations that all the signals in the overall adaptive system are bounded and tracking errors lie within a prespecified bound.