• Membrane and Water Treatment
• /
• v.12 no.1
• /
• pp.23-35
• /
• 2021

A POM-membrane was fabricated by immobilizing a keggin type polyoxometalate (POM) H5PV2Mo10O40 onto the surface of microporous flat-sheet polymeric polyvinylidene fluoride (PVFD) membrane using a chemical deposition method. The POM-membrane was characterized by FT-IR, SEM and EDX to confirm existing of the POM onto the membrane surface. The POM-membrane was used to remove an anionic textile dye (Reactive Black 5 named as an RB5) from aqueous phases with a cross-flow membrane filtration and a batch adsorption system. The dye removal efficiency of the POM-membrane using the cross-flow membrane filtration system and the batch adsorption system was about 88% and 98%, respectively. The influence factors such as contact time, adsorbent dosage, pH, and initial dye concentration were investigated to understand the adsorption mechanism of the RB5 dye onto the POM-membrane. To find the best fitting isotherm model, Langmuir, Freundlich, BET and Harkins-Jura isotherm models were used to analyze the experimental data. The isotherm analysis showed that the Langmuir isotherm model was found to the best fit for the adsorption data (R2 = 0.9982, qmax = 24.87 mg/g). Also, adsorption kinetic models showed the pseudo second order kinetic model was found the best model to fit the experimental data (R2 = 0.9989, q = 8.29 mg/g, C0 = 15 ppm). Moreover, after four times regeneration with HNO3 acid, the POM-membrane showed high regenerability without losing dye adsorption capacity.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.2
• /
• pp.52-57
• /
• 2005

The increasing automobiles continue to cause air-pollution problem s worse than ever. In fact, many automobile research are involved in how to reduce exhaust emissions effectively specially in $NO_X$ and PM to comply with stringent emission standards, Euro V. This research emphasized on the development of continuous regeneration DPF technology which was one of promising removing technology of particulate matters because of its comparability and high applicability. In addition, this research discussed on some design points of view through correlation study by com paring the experimental data with computational results by the introduction of commercial codes such as CFD-ACE+ and KIVA-3V. The numerical simulation on the performance of continuous regeneration DPF apparatus and corresponding emission characteristics has been predicted well enough and verified with experimental results. The pressure and average temperatures are decreased to about 2.6% and 1.4% respectively under a full engine load condition mainly due to back pressures raised by diesel particulate filter. Pressure, temperature and heat releasing rates tend to decrease specially at higher engine load, but they are not affected at lower engine load regions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.7
• /
• pp.3224-3231
• /
• 2012

It is necessary to study more integrated and objective method of urban compactness evaluation. Accordingly, the author examined precedent study and references related to the theory of compact city with the aim of deducing the urban planning factors from them. And then, these factors are objectified through the survey and interview with experts, and each of the factors is given a weighting by the AHP(Analytic Hierarchy Process) Method. Based on these evaluation model, the urban compactness of Korean Metropolitan Cities such as Busan, Incheon, Daegu, Gwangju, Daejeon, Ulsan, are analyzed their relative gap. The result of this study, as a foundational data for decision-making on the urban policy, could be useful for compact city planning such as regeneration of old town center etc.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.19 no.1
• /
• pp.9-27
• /
• 2021

As an example of research activities in decontamination for decommissioning, new data are presented on the options for corrosion layer dissolution during the decommissioning decontamination, or persulfate regeneration for decontamination solutions re-use. For the management of spent decontamination solutions, new method based on solvent extraction of radionuclides into ionic liquid followed by electrodeposition of the radionuclides has been developed. Fields of applications of composite inorganic-organic absorbers or solid extractants with polyacrylonitrile (PAN) binding matrix for the treatment of liquid radioactive waste are reviewed; a method for americium separation from the boric acid containing NPP evaporator concentrates based on the TODGA-PAN material is discussed in more detail. Performance of a model of radionuclide transport, developed and implemented within the GoldSim programming environment, for the safety studies of the LLW/ILW repository is demonstrated on the specific case of the Richard repository (Czech Republic). Continuation and even broadening of these activities are expected in connection with the approaching end of the lifespan of the first blocks of the Czech NPPs.

• Applied Chemistry for Engineering
• /
• v.31 no.5
• /
• pp.575-580
• /
• 2020

In this study, we simulated an amine regeneration process with heat-stable salts removal unit. We derived the optimal operating conditions considering the flow rate of waste, the removal rate of heat-stable salts, and the loss rate of MDEA (methyl diethanolamine). In the amine regeneration process that absorbs and removes acid gas, heat-stable salt impairs the absorption efficiency of process equipment and amine solution. An ion exchange resin method is to remove heat-stable salts through neutralization by using a strong base solution such as NaOH. The acid gas removal process was established using the Radfrac model, and the equilibrium constant of the reaction was calculated using Gibbs free energy. The removed amine solution is separated and flows to the heat-stable salts remover which is modeled by using the Rstoic model with neutralization reaction. Actual operation data and simulation results were compared and verified, and also a case study was conducted by adjusting the inflow mass of removal unit followed by suggesting optimal conditions.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.34 no.4
• /
• pp.428-434
• /
• 2008

Introduction: Piezosurgery device is one of the most commonly used instrument on the intraoral surgery such as maxillary sinus lift and autogeneous bone graft. Piezosurgery instrument also contains the tips that are manufactured especially for the convenient bone graft, which now many surgeons apply them for collecting bone graft materials in the curettage method for the restoration of skull defects. However, objective data has not been shown concerning the effects about bone graft with using Piezosurgery. Therefore we investigated the effects of Piezosurgery on the rabbit-skull defect healing. Materials & Methods: To investigate the regeneration of the bony defect with various bone graft, 10 adult New Zealand white rabbits (average weight : $2.8{\pm}0.3kg$, about 12weeks) were used. The four circular bony defects measuring 6mm in diameter were made with Piezosurgery device on each rabbit cranial bone. The harvested bone tissues during defect formation were also used for autogeneous bone graft. They were grafted into the defects in a various type; block type (Group 1), particulated type by the bone mill (Group 2), chopped type by curette shaped Piezosurgery tip (Group 3), the defect without any graft was served as control (control group). The animals were sacrificed after 6 weeks and bone regeneration capacity was evaluated histomorphometrically. Result & Conclusion: Autogeneous bone graft harvested using a Piezosurgery instrument showed satisfactory bone regeneration. There was no conspicuous difference bone prepared among by bone mill or Piezosurgery and block bone graft. Therefore, the bone harvested from the intraoral site near the operation field using the piezosurgery device can be a feasible and reliable graft for intraoral bony defects.

• Journal of Korean Society of Forest Science
• /
• v.89 no.2
• /
• pp.185-197
• /
• 2000

This study was carried out to research structure of forest vegetation and site condition, and supply basic data for conservation of pine forest and ecologically sustainable forest management and control in Anmyondo area. The forest of Anmyondo were largely classified as four forest community : Pinus densiflora community, Pinus thunbergii community, Pinus rigida community, and Quercus variabilis community. Organic matter, total nitrogen, and other nutrients in soil of the study area were relatively low, and average soil pH was 4.9. Soil texture was sandy clay or heavy clay and so the aeration and permeability could be poor. In this study site, the methods such as the promotion of germination of pine seeds through removal of forest floor and inducement of natural regeneration through such method as regeneration under shelter wood would be better than the method such as afforestation after clear-cutting for conservation the pine forests. Also, it will be a good method to practice tending for hardwood species in the dominant areas by hardwood species.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.28 no.1
• /
• pp.25-42
• /
• 2010

One of the important roles of worflow is color management. In general, color management technique, which is called CMS(color management system), is a method to solve problems that show different characteristics of color regeneration in output devices, and the characteristics of output devices is created in data file called ICC(International Color Consortium) profile. In addition, ICC profile is used to manage color in workflow, and includes other functions, process management and printing quality management. In domestic printing market, workflow is in the pipeline at rapid speed along with CTP, and use of ICC profile required for color management is also in rapid progress. Therefore, this paper produced optimal ICC profile through experiment from the work of linearizing devices used in each field to color conversion work. Moreover, the paper confirmed how ICC profile will be used in printing field. In the profiling experiment based on hardcopy proofing, photographed copy and chrominance were compared by printing out in proof the image created through application and color conversion with the use of camera profile and proof profile produced in colorimetric method. By evaluating if color is expressed accurately from input to output through colorimetric color conversion experiment as above, the paper intended to propose color management method using optimal profile in printing process.

• Journal of the Korean Chemical Society
• /
• v.6 no.2
• /
• pp.117-121
• /
• 1962

The waters throughout Taegu area for 87 points were analysed and according to the analytical data, following unfavorable characteristics for industrial uses were given: (1)Shows strong hardness, (2)Has high ratio of ignition residue to evaporation residue, (3) pH value is over 7, (4) Contains considerable quntities of iron.And then investigated the exchange rate and regeneration level of iron ion using cation exchange resin, Lewatit KS.When the hard water containing 2.2 ppm of iron with 18.4 ppm of calcium and 6.2 ppm of magnesium was passed through the ion exchange resin under $3cc/cm^2/min$ in exhaustant flow rate, exchange rate of iron reached to 42% after 300 hours flow. The exchange efficiency shows abrupt decreasing in initial stage of flow up to 100 hours flow. The exchanger which contains iron was regenerated with 10% sodium hydroxide aqua solution under SV (space velocity) 4. By this method, 57% of iron was eliminated from exchanger while calcium and magnesium are removed as much as 85% and 87% respectively.

• Clean Technology
• /
• v.23 no.4
• /
• pp.393-400
• /
• 2017

In this study, we have developed a process for separating and recovering Ni and Fe in solution through a new solvent instead of TBP and Alamine336, which are solvents used in the conventional solvent extraction method. Experimental conditions were optimized through lab test and a $10L\;h^{-1}$ pilot plant was constructed for commercialization. In addition, the process data for mass production were obtained through pilot experiment and it was confirmed that there is no problem in product quality that can be used through the corrosion test of ferric chloride.