• Geophysics and Geophysical Exploration
• /
• v.7 no.4
• /
• pp.251-255
• /
• 2004

Electric cables such as multi-interphone cables and ribbon cab]os are commonly used for data aquisition in the DC resistivity survey. In general, electromagnetic induction may occur in the electric cables when electric current flows through them. In case of using multi-interphone cables in the DC resistivity survey, electromagnetic induction could take place due to the entangled wires of the multi-interphone cables, when the current flows through them. Then, the electromagnetic induction may cause measured DC resistivity data to be distorted. In this study, a monitoring system with PXI (PCI Extention for Instrumentation) was constructed to examine signal distortion on the DC resistivity data, attributed to the electromagnetic induction. Common electric cables used in the DC resistivity survey were tested to observe the waveforms of the electric voltages. The waveforms measured were compared to examine signal distortion due to the electromagnetic induction. The results may provide information on the resistivity data obtained using different electric cables in the DC resistivity survey. The distortion of waveforms attributed to the electromagnetic induction wat not observed when using ribbon cables for DC resistivity data aquisition, while the distortion were observed when using multi-interphone. Therefore, the ribbon cables provide better quality of data than other cables in the DC resistivity data aquisition.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2643-2645
• /
• 2001

In this paper, a problem of limited sampling time that occurs essentially in digital data acquisition system is discussed. Low sampling frequency and a lot of processed data in micro-controller interferes normal operation of the controller from acquiring information in some case. To settle this problem, we design the sub-system which consists of a new simple micro-controller. which is managed the particular sensor making the trouble to main-controller system.

• Journal of the Korea Society of Computer and Information
• /
• v.12 no.2 s.46
• /
• pp.151-159
• /
• 2007

It is very important to collect all production-related status values during the manufacturing process of semiconductor. The analysis results of the collected data can be used for the operation rate, fault diagnosis, process control and removal of predicted obstacles of equipments, eventually contributing to the improvement of production efficiency. For this propose. many IC makers have adopted EES(Equipment Engineering System). As the use of web has become a daily lift activity lately, it has been suggested to expand the scope of monitoring equipments using HTTP or SOAP protocols. To fulfill the web-based EES, EDA(Equipment Data Aquisition) should be facilitated first by integrating and standardizing various forms of messages generated from many different semiconductor equipments. In this paper, a method for integration between different types of information is suggested based on the analysis of various protocols used for the communication between semiconductor equipments. In addition, a software architecture to support the method is desisted.

• Proceedings of the KSRS Conference
• /
• 2009.03a
• /
• pp.367-370
• /
• 2009

한국해양연구원에서는 2009년 발사 예정인 통신해양기상위성(COMS: Communication, Ocean and Meteorological Satellite)의 해색센서인 정지궤도 해양위성(GOCI: Geostationary Ocean Color Imager) 데이터의 수신, 처리, 배포를 위한 해양위성센터(KOSC: Korea Ocean Satellite Center)를 구축하고 있다. 2005년 "해양위성센터 구축사업"의 시작으로, 전파 수신 환경 등의 조건을 고려하여, 안산에 위치한 한국해양연구원 본원으로 해양위성센터의 위치를 최종 확정하여 구축을 진행하고 있다. 2009년 3월 현재 수신시스템(GDAS: GOCI Data Aquisition System), 자료전처리시스템(IMPS: Image Pre-processing System), 자료처리시스템(GDPS: GOCI Data Processing System), 자료관리 시스템(DMS: Data Management System), 통합감시제어시스템(TMC: Total Management & Controlling System), 기관간 자료교환시스템(EDES: External Data Exchange System) 등이 구축 완료되었고, 위성자료 배포시스템(DDS: Data Distribution System)을 구축하고 있다. 고용량 데이터의 원활한 전송을 위한 데이터센터를 비롯하여 사용자관점에서의 시스템 구축을 추진하고 있으며, 위성 발사 후 사용자 등록을 시작할 계획이다.

• Publications of The Korean Astronomical Society
• /
• v.19 no.1
• /
• pp.101-107
• /
• 2004

This paper describes the digital back-end system for getting the data to analyze the user observation mode by digitalize the analog data after receiving the space radio using the radio telescope, The received analog data will be digitalized by high-speed sampler with 1 Gsps for 4 channel frequency band of millimeter wave, and the digital data will be transported through the fiber-optic digital transmission system and WDM(wavelength division multiplex) to observation building, The wideband digital FIR(Finite Impulse Response) filters analyze the data for user observation mode to record the data in high-speed recorder with 1 Gbps. In this paper, we introduce the overall system configuration and features combined by various information and communication technology in radio astronomy briefly, which will be adopted by KVN(Korean VLBI Network).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.1
• /
• pp.47-55
• /
• 2012

This paper describes the developed HILS and test equipment in order to test the performances of MMW(Millimeter-Wave) seeker which can detect and track a high speed of short-range ballistic missile and aircraft. This system is used to 141 horn antenna array, array switching, and gain and phase control algorithm to simulate various kind of targets and trajectory of high speed and maneuver moving target. In addition, it simulates not only velocity and range for these targets but also clutter and jamming environments. System configuration and implementation and the measurement results of major subsystems such as target motion simulator, simulation signal generator, high speed data aquisition unit, and central control unit are presented. These systems could verify the detection and tracking performance of MMW seeker through dynamic real-time test based on simulation flight scenario.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.2029-2033
• /
• 2007

오늘날 특정 유역에서의 수문현상 및 수문순환에 대한 분석을 위한 연구가 활발히 진행되고 있다. 이를 위해서는 수문자료의 관측은 반드시 수반되어야 하며, 관측자료의 품질관리 및 원시자료의 관리 등이 요구되고 있는 실정이다. 관측된 수문자료의 품질관리라 함은 자료의 신뢰도 분석과 자료의 보완의 두 과정을 포함한다. 여기서, 신뢰도 분석이라 함은 자료 속에 포함된 불확실성을 판별하는 작업을 의미하며, 자료의 불확실성은 위에서 언급된 자료의 불충분 및 불안정을 제외한 부정확, 불일관성에서 비롯된다. 자료의 보완이라 함은 자료의 신뢰도 분석을 통하여 자료 속에 포함된 불확실한 성분들을 찾아내고, 이를 제거한 후 완전한 자료로 대체하고, 자료가 결측된 경우 공백을 연결함으로써 자료의 완전성을 유지하거나 또는 불충분한 자료를 확장하는 일련의 보완작업이라고 정의한다. 자료의 품질을 결정하는 주요 인자는 크게 관측소 관리의 하드웨어적인 측면과 자료 분석의 소프트웨어적인 측면이 있다. 하드웨어적인 측면에서의 수문자료 품질관리를 위해서 본 과제에서는 현장에 설치된 수위계, 강우량계의 센서 등에 대한 장비를 점검하고, 현장실측을 통해 지속적으로 측정값을 보정해주는 역할을 수행하고 있으며, 소프트웨어적인 측면에서 수문자료의 품질관리를 위해서는 수문자료의 수집 단계부터 시작하여 데이터베이스 저장, 필터링, 통계분석, 웹 및 C/S(Client Server)를 통한 배포 등의 일련의 자료 처리 과정을 수행할 수 있는 수문자료관리 프로그램을 웹 시스템과 C/S로 분류하여 정의내릴 수 있다. 본 연구에서는 수문자료의 관리자 입장에서의 보다 효율적이고 체계적으로 자료를 관리하고 분석하기 위한 방안으로 수문자료관리시스템(Hydrologic Data Aquisition and Management System, HDAMS)을 개발하였다. 이 시스템은 안양천 유역에서 시범 적용하고 있으며, 범용성을 전제로 개발되었다. 또한 수문자료 관리 프로그램의 DB 구조 및 DB 자료를 활용한 다양한 분석기능은 갖도록 설계하였으며 계획된 데이터베이스 구조를 바탕으로 계측기 인터페이스와 사용자 인터페이스, 데이터베이스 간의 연동이 원활히 이루어지도록 개발하고자 한다.

• Proceedings of the KIEE Conference
• /
• 1998.07g
• /
• pp.2215-2217
• /
• 1998

A remote maintenance system, which enables an engineer to check and treat machines installed at remote site with the help of data communication, has been developed. The maintenance of machines with the traveling of engineers is much costly in time and economically. With the developed system, the engineer at the remote site can diagnose malfunctioning machines. The remote maintenance system is composed of video conferencing system, camera control system and signal aquisition system. The developed system has been tested on the 100Mbps ATM network to evaluate its ability to diagnose remote machines.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.950-955
• /
• 2003

This paper introduces an enhanced condition monitoring and diagnosis system recently developed for rotating machinery. In the system, the data aquisition/monitoring signal processing, machine condition classifier, case-based reasoning and demonstration modules are effectively integrated with user-friendliness so that machine operators can easily monitor and diagnose the status of rotating machinery in operation. Some of the new features include the directional spectrum, case-based reasoning and neural network techniques. And the demonstrator modules for fault diagnosis of a Bear driving system and for basic understanding of the rotor dynamics are provided to help the potential users better understand the system.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.673-678
• /
• 2002

Laboratory calibration chamber tests for cone penetrometers, pressuremeters and dilatometers in cohesionless soil specimens have been conducted by numerous researchers. However, there have been only few applications to compacted or preconsolidated cohesive soils. Therefore, for the first time, Calibration Chamber System was developed in Korea University. This can be attributed to the extremely time consuming and laborious process involved in the preparation of large cohesive soil specimens in addition to other complexities involving instrumentation for pore pressure monitoring and the need for maintaing saturation by back pressure. Chamber System with similar principle as LSU Chamber System was made of more strengthen and complementary form by increasing system diameter(1.2m), carrying out 1st and 2nd consolidation process in one system for smooth and safe work, accurate Data Aquisition.