• Progress in Superconductivity and Cryogenics
• /
• v.14 no.3
• /
• pp.5-8
• /
• 2012

Superconducting windings of synchronous machine have to be operated in below the critical temperature, critical current density and critical magnetic field. If one of these characteristics does not satisfied, then the quench occurred in superconducting winding. Especially the armature current dramatically increased as the superconducting generator is short-circuited at the rated load condition and magnetic field in field winding increased due to the armature current. Therefore, damper is required to reduce the magnetic field of field winding which increases reliability of the superconducting generator. Damper dimension can be decided by time constant[1-2]. In this paper the basic model is high-power and low-speed superconducting generator. Damper time constant was calculated from the changed damper thickness and material. Magnetic flux of field coil at the basic model and changed damper time constant model is analyzed.

• 전기의세계
• /
• v.20 no.2
• /
• pp.19-26
• /
• 1971

To proteting hunting of synchronus motor a new one which has two field windings is designed. One is main field winding excited constantly and the other is control field winding excited only during the load of motor changes. The oscillation of the motor is controlled by increasing or decreasing the control field excitation. To determine the optimal field excitation the Pontryagin's minimum principle is applied. Also this paper gives the optimal trajectories of the motor and it's transition time. This motor has some of better properties than the old motor with damper winding. These phroperties are (1) there is no hunting (2) the transient stability is improved (3) transition time is very short.

• Proceedings of the KIEE Conference
• /
• 1997.07a
• /
• pp.133-135
• /
• 1997

In this paper, we propose a new type of rotor construction in the permanent magnet synchronous motor. By using plural permanent magnets for one-role of the rotor, it is possible not only to reduce space harmonics of air-gap fields but also to provide spacs for damper windings in the inter-pole space. The dimensions of the plural permanent magnets are derived by Fourier analysis. Based on the investigation by numerical analyses. we propose an optimal rotor construction in view of both the reduction of space harmonics and the damping effect.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.3
• /
• pp.159-164
• /
• 2000

This paper treats the optimization of rotor construction in the permanent magnet synchronous motor (PMSM) for electric vehicle (EV). While the field system of PMSM has generally one magnet per pole, we replace the magnet into plural sub-magnets. The dimensions of each sub-magnet are determined by the concept of pulse width modulation (PWM). By adopting the proposed rotor construction, we can not only reduce the space harmonics of the air-gap field but also provide space for rotor bars (i.e., damper windings) around the direct-axis. From the investigation by hybrid EE-BE (coupled finite element and boundary element) method coupled with both electric circuit and motion equation, we verify that the construction is effective for practical use.

• Progress in Superconductivity and Cryogenics
• /
• v.4 no.2
• /
• pp.31-37
• /
• 2002

A 100 〔HP〕 rated synchronous motor with superconducting rotating field winding has been designed based on the formulated equations established from 2 dimensional magnetic field distributions in a cylindrical coordinate The cross-section was drawn based on calculated design results via Fortran program and then modeled with FEM (Finite Element Method) to investigate the machine performances. First of all, the magnetic field distributions are analysed in many ways according to the field directions and the armature currents. Especially after the rotating Held winding is arranged with BSCCO-2223 high-temperature superconducting(HTS) pancake coils, the exerted magnetic field normally on the HTS tape is calculated through FEM. And the machine output power is calculated according to the torque ang1es which lie between the field and the armature main flux lines. Moreover, this Paper includes the eddy-current loss variations of a copper damper located between the field and the armature coils and design considerations of the 100 HP HTS motor utilizing ferro-magnetic material.

• 전기의세계
• /
• v.21 no.2
• /
• pp.20-24
• /
• 1972

The transient stability of the synchronous motor is generally improved by damper winding or flywheel. However the synchronous motor at full load will be pulled out from normal operation state when the period of power failure exceeds approximately ten cycle per second. This paper studies the method of improving the stability of synchronous motor by equipping the phase slipping switch between the motor and power source. This paper shows the motor does not pull out, which results from the decrease of power angle to about 30 electrical degrees by means of the switch even when the relatively long period of power failure brings the power angle to some 150 electrical degrees.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.962-963
• /
• 2015

This paper proposes a sensorless V/f control method of the interior mounted permanent magnet synchronous motor without damper winding. Arithmetic computation is simpler than vector control. And the lower cost price, dynamics and stability is guaranteed. When the loss of synchronization occurs with the load disturbances, the stability loop with a reduced order observer is applied quickly and accurately to improve the speed error.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.4
• /
• pp.167-173
• /
• 1999

The use of high-Tc superconducting synchronous motor in power machinery has many advantages such as reduced power dissipation, size and weight. This paper presents the ac loss simulation in the rotor having an high-Tc superconducting field winding using Ag sheathed Bi-2223. The analysis was conducted with an equivalent model of the high-Tc superconducting motor with flux damper under transition condition during which the load varies from 0 watt to 250watts and from 250watts to 500watts. The simulation results show that the transient state lasts for about 3 seconds, and the ac losses decreased exponentially from the initial value above 20mW.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.2
• /
• pp.93-101
• /
• 2000

This paper presents a novel method for the transient of eddy currents in the dampers of a super-conducting synchronous generator(SCG). The method proposes a 2-D corrected model which takes into account the influence of leakage fluxes of the field winding ends by increasing the effective air gap in order to consider the high precision of the analysis for the conventional 2-D model. The electromagnetic fields for the corrected model are analyzed by the time-stepping finite element method, thus the eddy currents in the dampers and electro-motive forces(EMF) in the stator windings are calculated. As the results, it is proved the presented method is comparatively accurate by comparing measured phase EMF values and the simulation ones, where about 6.4% error at the maximum value of EMF is occurred between them.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.521-527
• /
• 2001

The dynamic performance analyses and tests for a 50kW turbo-generator (KIMM-TG50) were carried out. The operating concept of this machine is that it gets the initial driving force from the built-in motor-generator until it reaches its self-sustaining speed of 40,000 rpm, and then the driving mode is changed to self-operating mode by the combustor installed between the centrifugal compressor and the turbine. Due to winding mistake of motor-generator, the system could go only up to 22000 rpm by the motor so that high pressure air externally fed into the turbine was utilized to get the system to run up to 62,000 rpm thereafter. The vibration data collected during the tests revealed that the first bending critical speed is in near 5,600 rpm as predicted in the design stage of the rotor-bearing system, and that there were no other identifiable critical speeds up until 62,000 rpm due to high damping from the squeeze film damper-bearings supporting the rotor. This paper presented some of the experimental results along with dynamic performance predictions made in the design stage as a part of progress being made.