• Journal of Surface Science and Engineering
• /
• v.40 no.3
• /
• pp.149-158
• /
• 2007

Of all components of MCFC(molten carbonate fuel cell), corrosion of separator is one of the most decisive factor for commercializing of MCFC. In order to provide better understanding of corrosion behavior and morphology for gas channel of separator plate, post-analysis after cell operation for 1200 hours at $650^{\circ}C$ was performed by optical microscope, SEM and EPMA. Intergranular corrosion was observed on gas channel of separator plate. Corrosion product layer was identified as Fe-oxide, Cr-oxide and Ni-oxide by EPMA, and oxide thickness was measured with a $60{\mu}m-150{\mu}m$. Also, gas channel of separator was damaged by severe intergrannular attack with post analysis in consistent with immersion test. Moreover, pitting on the channel plate was observed with a depth of $18{\sim}24{\mu}m$. The results of immersion method are well agreement with post analysis measurements.

• Journal of Fisheries and Marine Sciences Education
• /
• v.22 no.4
• /
• pp.501-507
• /
• 2010

The ceramic contained paint was made to replace the lead sinker for gill-net with coated lead sinker. The ceramic contained paints were coated in various conditions on the lead sinker with 19g of weight and the optimal coating condition was studied. The adaptability of the coated lead sinker was checked through the anti durability test and fishing operation with gill-net. The case of "Main material 70 wt% + Urethane thinner 30 wt% (Main material 700 $m{\ell}$ + Thinner 300 $m{\ell}$)" showed the best in the coating characteristics depending on the combination ratio of the ceramic paint contained. The coated lead sinker dried at $100^{\circ}C$ inside oven was superior to the drying in the room temperature in its surface glossiness and anti durability and faster drying time than the one dried in normal temperature. The quadruple layers of coating on lead sinker with 4 times of dipping and drying application showed the super anti durability in the coating characteristics depending on the frequency of dipping. When press is applied to the coated lead sinker, the coated layer is not detached from the sinker. In addition, the coated lead sinker was not damaged or peeled at the fishing operation about 2 months in various depths within 50m and by the materials at the bottom (sand, stone and gravel stone) and it was in good condition.

• Journal of Surface Science and Engineering
• /
• v.31 no.2
• /
• pp.117-126
• /
• 1998

In this study, the residue remaining on the silicon wafer during the oxide overetching using $C_4F_8/H_2$ helicon were plasmas and effects of various cleaning and annealing methods on the removal of the remaining residue were investigated. The addition of 30%$H_2$ to the C4F8 plasma increased the C/F ratio and the thickness of the residue on the etched silicon surface. Most of the residuse on the etched surfaces colud be removed by the oxygen plasmsa cleaning followed by thermal annealing over $450^{\circ}C$. Hydrogen-coataining residue formed on the silicon by 70%$C_4F_8/30%H_2$ helicon plasmas was more easily removed than hydrogen-free residue formed residue formed by $C_4F_8$ helicon wear plasmas. However, damage remaining on the silicon surface overetched using 70%$C_4F_8/30%H_2$ helicon plasmas was intensive and the degree of reocvery duing the post-annealing was lower.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.7A
• /
• pp.1063-1075
• /
• 2000

This paper proposes an adaptive error concealment technique for compressed video. Since redundancy is extracted out during compression process, compressed video is vulnerable to errors which occur during transmission of video over error prone networks such as wireless channels and Internet. Error concealment is a process of reconstructing video out of damaged video bit stream. We proved that scalable encoding is very useful for error concealment. Analysis of experiments shows that some part of image is better concealed by using base layer information and other part of image is better concealed by using previous frame information. We developed a technique which enables to decide which methodology is more effective, adaptively, based on motion vectors and regional spatial activity. We used H.263v2 for scalable encoding, but, our approach could be applied to all DCT based video codec.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.05a
• /
• pp.128-133
• /
• 1999

In recent years, LSI devices have become more powerful and lower-priced, caused by a development of various wafer materials and an increase in the diameter of wafers. On the other hand, these have created some serious problems in manufacturing of wafers because materials used as semiconductor substrate are very brittle. In view of this fact, there are some trials to apply shear-mode(or ductile-mode) grinding for efficient manufacturing of semiconductor wafers instead of conventional lapping process. In fact grinding process that has not only more excellent degree of accuracy but also more adaptable to fully automated manufacturing than lapping, is already used in Si machining field. This paper described the elementary studies to establish the grinding technology of wafers. First, we investigated the variation of grinding force and the transition of grinding mode as various grinding conditions. Then, it was inspected that the change of grinding force affected the integrity such as the topography and the roughness of ground surfaces, and led to the chemical defects generation and distribution in damaged layer. The degree of defects was estimated by FT-IR(Fourier Transformed Infrared) Spectroscopy and Auger Electron Spectroscopy

• The Journal of Korean Academy of Prosthodontics
• /
• v.27 no.1
• /
• pp.213-222
• /
• 1989

It is considered that self-curing resin will induce a little pulpal irritation, if mixing time is insufficient. So this study was designed to compare four different conditions between control group and three experimental groups. Canine teeth of 20 cats used, and class V cavities were prepared on maxillary canine of cats. Control group was filled with zone and other experimental groups were filled with zone after the application of the self-curing resin. Animals of the experimental and control group were sacrified at 3 days, 1, 2, 3, 4 weeks after the experiment. The finding lead to the following conclusions ; 1. Odontoblasts of first and third experimental groups were condensed irregularly and were changed at early stage, and reapir was delayed. 2. Odontoblasts of second experimental group were condensed slightly but, histologic repair was appeared at 4 weeks after the experiment 3. In all groups, the damaged odontoblastic cell layer were eventually disappeared at 4 weeks after the experiment.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.10
• /
• pp.657-661
• /
• 2014

When an abnormal condition occurs due to a fault current at a consumer location where electricity is supplied through high-Tc superconducting(HTS) cable, the HTS cable would be damaged if there is no appropriate method to protect it. The fault-current-limiting type HTS cable that is suggested in this study has a structure of transport part and limit part. It conduct a zero impedance transport current at ordinary operations and carry out a fault current limiting at extraordinary operations. To make a perfect this structure, it is essential to investigate electrical properties of transport part that comprise the fault-current-limiting type HTS cable. In this paper, transport part that comprise HTS wire with copper stabilization layer is examined the current transport properties and the stability evaluation.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.67-71
• /
• 2000

The wear behaviors of ultrahigh molecular weight polyethylene pins against titanium alloy and stainless steel disks moving in two different kinematic motion were investigated by conducting repeat pass rotational sliding and linear reciprocal sliding wear tests. Linear reciprocal motion wore more the polyethylene pin than did repeat pass rotational motion for both disk materials. It means that the repeated directional change of contact stresses generates more wear debris in polyethylene. For the linear reciprocal sliding tests, titanium alloy disks were damaged with some scratches after one million cycles but no surface damage was observed on the polyethylene pins. On the other hand, for the repeat pass rotational sliding tests, all titanium alloy disks were severely abraded on the entire region of sliding track. This phenomenon can be interpreted by that stress fatigue under repeated sliding contact initiated titanium oxide layer wear particles from disk surface, and these hard particles were embedded into polyethylene pin and then they severely abraded the disk surface. From these results it can be concluded that the kinematic motion in pin-on-disk wear tests play a crucial role on the wear behaviors of UHMWPE pins against titanium alloy and stainless steel disks.

• Conservation Science in Museum
• /
• v.14
• /
• pp.1-5
• /
• 2013

This study was conducted to analysis and conserve a lacquered sheath excavated from Soochon-ri, Gongju, Korea. The lacquered sheath was collected together with iron relics. The lacquered sheath was damaged and lost the parts by the external pressure. Many parts were adhered with the rust. Firstly, the object was understanded to have the relation with the iron materials excavated together through the X-ray photographs. As the analysis of the lacquer layers, the report conducted to a study the method of production. After the analysis of relic, the conservation treatment was performed for the stability of original shape. And we made the protection frame for the storage and exhibition.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.3
• /
• pp.246-254
• /
• 2022

Localized heat can be generated using electrically conductive word-lines built into a 3D NAND flash memory string. The heat anneals the gate dielectric layer and improves the endurance and retention characteristics of memory cells. However, even though the electro-thermal annealing can improve the memory operation, studies to investigate material failures resulting from electro-thermal stress have not been reported yet. In this context, this paper investigated how applying electro-thermal annealing of 3D NAND affected mechanical stability. Hot-spots, which are expected to be mechanically damaged during the electro-thermal annealing, can be determined based on understanding material characteristics such as thermal expansion, thermal conductivity, and electrical conductivity. Finally, several guidelines for improving mechanical stability are provided in terms of bias configuration as well as alternative materials.