• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.2
• /
• pp.225-231
• /
• 2016

A military vehicle is driven at different usage modes with the army application and servicing conditions. For practical durability validation, DT(Development Test) on a new military vehicle should be run up to the durability target kilometers on test courses in the specified proving ground. Driving velocities with test courses at the endurance mode of DT are established definitely. However, OT(Operational Test) and initial endurance test of production car can't be performed only in the DT courses due to the development period limit. Therefore, this paper focuses on the method to analyze the relative road damages between the endurance test in DT and other endurance test. Road load acquisition tests on KLTV(Korean Light Tactical Vehicle) were implemented at 15 driving modes in off-road and cross-country courses of two tests. Wheel accelerations were processed through band-pass filter, and then the main frequency and maximum power of the signals were computed by PSD analysis. Finally, using the proving ground optimization based on RDS(Relative Damage Spectrum) characterization, the damage factors between off-roads of test courses were determined.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.4
• /
• pp.313-320
• /
• 2003

This paper deals with the optimal design of a elevator inverter system based on the customized IPM. The proposed method reduces dv/dt and di/dt, which resulted in the minimized conducted EMI noise without an additional circuitry. It only optimizes the value of gate resistor in the IGBT embedded in the IPM. In order to optimize the customized IPM to a elevator system, we simulated and measured the spike voltage and the motor surge voltage including the temperature variation due to the switching losses at the IPM case and heat-sink. As a result, thanks to the optimized value of the gate resister in the IPM, the conducted EMI noise is reduced approx. 5∼10 [dB$\mu$V] in a particular frequency domain.

• Journal of the Korean Ceramic Society
• /
• v.36 no.1
• /
• pp.15-20
• /
• 1999

Elevated temperature static fatigue behavior of silicon has been investigated by stress intensity/life test method. Static fatigue crack growth rate increase with the increase of temperature. Such tendency is found to be mainly related to the decrease of fracture toughness with the increase of temperature. That is, when static fatigue crack growth rate, da/dt is expressed by da/dt=AK1m, a constant A is a function of fracture toughness Kc and the exponent m is a constant which is independent of temperature or Kc. However, in the case of high temperature that glass phase is softened, the crack growth rate is found to be deviated from the above relation. This reason is, thus, discussed.

• Journal of the Korean Ceramic Society
• /
• v.29 no.8
• /
• pp.651-659
• /
• 1992

Fracture toughness of alumina was determined by IF, IS, DT, SEPB methods, and the data were inter-compared. Round robin test on IF and IS methods was also conducted under the participitation of 4∼5 domestic institutes. Fracture toughness data determined by IF, IS, DT methods were similar, while those by SEPB method were smaller. Variation of toughness data determined by IS method using 98N of indentation load was significantly small compared to those determined by any other methods. Round robin test results showed that toughness data determined by IF method at various institutes do not coincide each other, while those by IS method do well coincide. Thus, it was concluded that inter-confidence on fracture toughness data, if determined by IS method at all institute, can be established between institutes.

• Journal of Korea Multimedia Society
• /
• v.21 no.4
• /
• pp.478-484
• /
• 2018

The choice of the motion features influences the result of the human action recognition method directly. Many factors often influence the single feature differently, such as appearance of the human body, environment and video camera. So the accuracy of action recognition is restricted. On the bases of studying the representation and recognition of human actions, and giving fully consideration to the advantages and disadvantages of different features, the Dense Trajectories(DT) algorithm is a very classic algorithm in the field of behavior recognition feature extraction, but there are some defects in the use of optical flow images. In this paper, we will use the improved Dense Trajectories(iDT) algorithm to optimize and extract the optical flow features in the movement of human action, then we will combined with Support Vector Machine methods to identify human behavior, and use the image in the KTH database for training and testing.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.12
• /
• pp.70-80
• /
• 1997

This paper proposes a hierarchical Hausdorff distance (HD) matching algorithm baased on coarse-to-fine approach. It reduces the computational complexity greatly by using the pyramidal structures consisting of distance transform (DT) and edge pyramids. Also, inthe proposed hierarchical HD matching, a thresholding method is presented to find an optimal matching position with small error, in which the threshold values are determined by using the property between adjacent level of a DT map pyramid. By computer simulation, the performance of the conventional and proposed hierarchical HD matching algorithms is compared in therms of the matching position for binary images containing uniform noise.

• Journal of Biomedical Engineering Research
• /
• v.12 no.4
• /
• pp.261-266
• /
• 1991

As the ensemble averaged dz/dt signal during exercise gets smoothed, it is difficult to find the distinctive marks for estimation of stroke volume. The cross correlation function was made use of estimating these marks for automatic calculation by computer from the ensemble averaged dz/dt signal. LVET( Left Ventricular Ejection Time) and stroke volume were estimated based on the calculated parameters from the characteristic points. LVET, stroke volume calculated by hand, by the ensemble average and the cross correlation were compared for accuracy validation.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.438-447
• /
• 2019

As the IoT-based hyper-connected society grows, public-key cryptosystem such as RSA is frequently used for encryption, authentication, and digital signature. Public-key cryptosystem use very large (safe) prime numbers to ensure security against malicious attacks. Even though the performance of the device has greatly improved, the generation of a large (safe)prime is time-consuming or memory-intensive. In this paper, we propose ET-MR and ET-MR-MR using Euler sieve so it runs faster while using less memory. We present a running time prediction model by probabilistic analysis and compare time and memory of our method with conventional methods. Experimental results show that the difference between the expected running time and the measured running time is less than 4%. In addition, the fastest running time of ET-MR is 36% faster than that of TD-MR, 8.5% faster than that of DT-MR and the fastest running time of ET-MR-MR is 65.3% faster than that of TD-MR-MR and similar to that of DT-MR-MR. When k=12,381, the memory usage of ET-MR is 2.7 times more than that of DT-MR but 98.5% less than that of TD-MR and when k=65,536, the memory usage of ET-MR-MR is 98.48% less than that of TD-MR-MR and 92.8% less than that of DT-MR-MR.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.572-576
• /
• 1997

X-ray laminography and DT(digital tomosynthesis) that can form a cross-sectional image of 3-D objects promise to be good solutions for inspecting interior defects of industrial products. The major factors of the digital tomosynthesis that influence on the quality of x-ray cross-sectional images are also discussed. The quality of images acquired from the DT system varies according to image synthesizing methods, the number of images used in image synthesizing, and X-ray projection angles. In this paper, a new image synthesizing method named 'log-root method' is proposed to get clear and accurate cross-sectional images, which can reduce both artifact and blurring generated by materials out of focal plane. To evaluate the quality of cross-sectional images, two evaluating criteria: (1) shape accuracy and (2) clearness in the cross-sectional image are defined. Based on this criteria, a series of simulations were performed, and the results show the superiority of the new synthesizing method over the existing ones such as averaging and minimum method.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2003.11a
• /
• pp.221-228
• /
• 2003

The stress corrosion index of Kumamoto andesite are evaluated by two types of testing method. One is the uniaxial compression test under various water vapor pressures, and the other is the double torsion (DT) test under a constant water vapor pressure. For the uniaxial compression tests, the uniaxial compressive strength increases linearly with decreasing water vapor pressure on the double logarithmic coordinates. As the results, the stress corrosion index obtained is estimated 44. On the other hand, in the DT test, the relaxation (RLX) test and the constant displacement rate (CDR) test were conducted. For the CDR test, as the displacement rate of loading point increases, the crack velocity increases. However, the fracture toughness is constant regardless of the change in displacement rate and the average fracture toughness is evaluated $2.07MN/m^{3/2}$. For the RLX test, the crack velocity-stress intensity factor curves are smooth and linear. The stress corrosion index estimated from the curves is 37. Comparing stress corrosion indexes in the uniaxial compression test and the DT test, there is no significant difference in these values, and they are considered to be in coincident each other regardless of testing methods. Therefore, it is concluded that stress corrosion is one of material constants of rock.