• 한국분무공학회지
• /
• 제14권4호
• /
• pp.184-189
• /
• 2009

Recently, ultrafine particles emitted from internal combustion engine is main concern because of its well known adverse health effects. So Europe decided to start the regulation about diesel engine particle number emissions. The nanoparticles smaller than 50nm in diameter have the ability to penetrate deep into interstitial tissue of luge, where they may cause severe respiratory inflammation and acute pulmonary toxicity. Recent studies have showed that spark ignition engines emit particles number concentration comparable to those from diesel engines with DPF under high load and rich mixture conditions, including cold starts and acceleration. So this study investigated emission characteristics of ultrafine particles according to fuel injection type in gasoline vehicles and LPG vehicles. The test vehicles were tested on CVS-75 and NEDC vehicle test mode using the chassis dynamometer, CPC system applied as a particle measuring instrument at the end of dilution tunnel. As a result, the correlation between fuel injection type and particulate emission was determined. GDI vehicle emitted 10 times higher particles than PFI vehicles, and compared to Mixer and LPGI type LPG vehicle, LPLI vehicle emitted particles high.

• 한국식품영양과학회지
• /
• 제23권1호
• /
• pp.110-115
• /
• 1994

To investigate the effect of potato lipoxygenase on the farinograph characteristics of wheat flour dough, composite flours containing enzyme-active potato flor (EPF) and hot-ar dried potato flour(HPF) were used. EPF was made by freeze-drying potato tuber. DPF (denaturated potato flour) was prepared by holding EPF at 8$0^{\circ}C$ for 18 hr in a dry oven. The potato flours were added to wheat flour at a level of 10% , respectivley. EPFB (enzyme-active potato flour blends, 90% wheat flour +105 enzyme -active potato flour) containing lipoxygenase activity gave higher farinogram peak time and higher stability values, lower MTI (mixing tolerance index ) and lower weakness values than those of HPFB(hot-air potato flour blends, 90% wheat flour + 10 % hot-air potato flour). Moreover, then lipoxygenase was added to DPFB(denatured potato flour blends , 90% wheat flour + 10% denatured potato flour) at a level of EPFB, it resulted in increasing stability, peak time and decreasing MTI , weakness at a level of EPFB. When the lipoxugenase was added to wheat flour with fumaric acid at alevel of 6.5 $\times$ 10units/g flour, lipoxygenase overcame the deleterious effects that fumaric acid including activated double-bond compounds have at mixing stability. Also the addition of liposxygenase with linoleic acid to defatted wheat flour resulted in the increase in stability and decrease in MTI value compared with those of linoleic acid and defatted wheat flour.

• 한국세라믹학회지
• /
• 제43권8호
• /
• pp.472-478
• /
• 2006

The effect of compositional and processing variables on a nitriding reaction of silicon powder compact and subsequent post sintering of RBSN (Reaction-Bonded Silicon Nitride) was investigated. The addition of a nitriding agent enhanced nitridation rate substantially at low temperatures, while the formation of a liquid phase between the nitriding agent and the sintering additives at a high temperature caused a negative catalyst effect resulting in a decreased nitridation rate. A liquid phase formed by solely an additive, however, was found to have no effect on nitridation for the additive amount used in this research. The original site of a decomposing pore former was loosely filled by a reaction product ($Si_3N_4$), which provided a specimen with nitriding gas passage. For SRBSN (Sintered RBSN) specimens of high porosity, only a marginal dimensional change was measured after post sintering. Its engineering implication for near-net shaping ability is discussed.

• 항공우주기술
• /
• 제7권1호
• /
• pp.151-160
• /
• 2008

본 논문에서는 발사체에 적용하는 전기-유압식 추력벡터제어 구동장치시스템의 합성공진 현상에 대한 해석 연구결과를 기술한다. 합성공진 현상은 위치서보 구동장치시스템을 유연한 발사체 기체구조체 지지부에 장착하였을 때 발생한다. 이는 관성부하를 갖는 전기-유압식 위치서보 시스템의 유압공진 현상과 유연한 기체구조체 지지부의 구조공진 현상의 합성에 의하여 발생한다. 합성공진 현상은 발사체 제어시스템에 의하여 되먹임 및 증폭되어 안정성을 악화시킬 수 있다. 이와 같은 현상을 정확하게 예측 및 분석할 수 있는 비선형 모델을 개발하였으며 이에 기반을 둔 합성공진 억제 특성이 우수한 동적 압력 되먹임(dynamic pressure feedback) 제어기법을 개발하였다.

• 한국광학회지
• /
• 제1권1호
• /
• pp.65-72
• /
• 1990

최대 10kJ의 에너지를 공급할 수 있는 Mather형 플라즈마 집속장치를 설계, 제작하였다. 이 DPF 장치의 전기 방전 특성을 알기 위해 Rogowski 코일을 제작하고 방전전류, 전압을 측정하여 본 system 의 저항과 인덕턴스는 각각 $20m\Omega과 0.2{\mu}H로 밝혀졌다. 플라즈마 전류 sheath의 이동속도는 충전개스 압력과 전압에 따라 $P^{-0.25}\timesV^{0.38}$의 함수로 비례하며 집속된 플라즈마의 크기는 직경 3mm, 길이 17mm로 밝혀졌다.

• 대한기계학회논문집B
• /
• 제38권8호
• /
• pp.657-663
• /
• 2014

차량에 탑재하여 운행 중 배출가스를 측정할 수 있는 이동식 배출가스 장비(PEMS)를 활용한 결함확인검사 방법을 미국은 2007년부터 시행하였고, 유럽은 2013년 EURO6부터 도입할 계획을 수립했다. 따라서 한국도 국내의 대형차 배출가스 관리의 중요성을 고려할 때 PEMS를 활용한 실 도로 주행 특성을 반영한 측정 방법의 도입이 필요한 시점이다. PEM의 다양한 활용 방안을 위하여 도로유형, 매연저감장치 및 공회전제한장치 그리고 에어컨 작동에 따른 배출가스 평가를 수행하였다. 본 연구는 PEMS을 활용한 상용차 결함확인 검사 방법을 분석하여 국내 실정에 적합한 대형차 결함확인 검사제도 시행에 필요한 기초자료를 마련하고자 한다.

• 대한기계학회논문집B
• /
• 제41권6호
• /
• pp.397-407
• /
• 2017

본 논문에서는 연비손실 없이 높은 $NO_X$ 저감성능을 보이는 승용 디젤 엔진의 SCR 시스템을 위한 요소수의 분사전략을 제시하였다. 배출되는 $NO_X$량 대비 요소수가 화학량론적 1:1인 피드포워드 분사 전략과 함께 모델기반의 촉매 내 $NH_3$ 흡장률 추정 기법을 통하여 피드백 분사 제어전략을 함께 사용함으로써 과도상태에서 $NO_X$ 저감성능과 $NH_3$ 슬립 성능을 모두 만족시키고자 하였다. 제안된 분사전략을 적용하여 디젤산화촉매기와, 미립자필터가 장착된 2.2L 디젤 엔진을 갖춘 실제 차량에서의 실험을 통하여 제어기의 높은 $NO_X$ 저감률과 낮은 $NH_3$ 슬립 성능을 검증하였다.

• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.7-12
• /
• 2012

Cooled EGR system is widely used to reduce NOx emissions in diesel engine. But when EGR rate was increased, combustion stability was worsened and PM level was increased. So determining optimized control point of EGR rate is important. In order to determine this point, it is important to figure out the effect of EGR system on the exhaust emissions. In this research, NOx and PM emissions were analyzed with various coolant temperature supplied to the EGR cooler at several positions such as downstream of turbocharger, upstream and downstream of DPF. Effects of some variables such as EGR rate, hot / cooled EGR and change of injection timing were estimated. And $CO_2$ emissions were measured at exhaust and intake manifold to calculate EGR rate at each engine operating condition. Also combustion analysis was performed in each engine operating conditions. In the result of this study, there was trade-off between NOx emissions and PM emissions. When EGR rate was increased, combustion pressure was decreased and COV of IMEP was increased.

• 한국자동차공학회논문집
• /
• 제15권6호
• /
• pp.128-136
• /
• 2007

It is well known that two representative methods satisfy EURO-IV regulation from EURO-III. The first method is to achieve the regulation through the reduction of NOx in an engine by utilizing relatively high EGR rate and the elimination of subsequently increased PM by DPF. However, it results in the deterioration of fuel economy due to relatively high EGR rate. The second is to use the high combustion strategy to reduce PM emission by high oxidation rate and trap the high NOx emissions with DeNOx catalysts such as Urea-SCR. While it has good fuel economy relative to the first method mentioned above, its infrastructure is demanded. In this paper, the number distribution of nano PM has been evaluated by Electrical Low Pressure Impactor(ELPI) and CPC in case of Urea-SCR system in second method. From the results, the particle number was increased slightly in proportion to the amount of urea injection on Fine Particle Region, whether AOC is used or not. Especially, in case of different urea injection pressure, the trends of increasing was distinguished from low and high injection pressure. As low injection pressure, the particle number was increased largely in accordance with the amount of injected urea solution on Fine Particle Region. But Nano Particle Region was not. The other side, in case of high pressure, increasing rate of particle number was larger than low pressure injection on Nano Particle Region. From the results, the reason of particle number increase due to urea injection is supposed that new products are composited from HCNO, sulfate, NH3 on urea decomposition process.

• 한국자동차공학회논문집
• /
• 제5권4호
• /
• pp.130-141
• /
• 1997

Work on the reduction of particulate matter(PM) from a diesel vehicl has led to a new trp system and a control method to control the combustion rate of the PM filtrated in the trap, which was named as 'Active Exhaust Feeding Regeneration(AEFR) System' by its operation mechanism. Ceramic cordierite filter is a major component of the trap and susceptible to thermal shock. Therefore the system should be designed to reduce the peak temperature and temperature gradients in the trap ; these have been considered to be the main factors causing thermal shock of the filter during the regeneration. It uses the engine's exhaust gas partially for the regeneration of the ceramic filter. It controlled bypass flow rate of the engine's exhaust gas precisely to control the temperature of the gas entrained into the filter. Gas temperatures were measured inside filter, and the oxygen concentration at the outlet of the filter was also monitored during the regeneration to analyze the combustion process of the PM. The temperature distributions and temperature gradients in the filter during the regeneration varied widely according to the regeneration control schemes. Finally, this system shows relatively low peak temperature and temperature gradients in the filter during its regeneration. It is considered that this system uses a mew method to control the combustion rate of the PM, which is different from the methods used in the previous studies.