• Proceedings of the Membrane Society of Korea Conference
• /
• 2002.05a
• /
• pp.81-85
• /
• 2002

Small angle light scattering and field emission scanning electron microscope have been used to quantify the kinetics of liquid-liquid separation behavior during water vapor(RH52%[$\pm$3%] at 27$^{\circ}C$) quenching (non-solvent induced phase separation, NIPS) of polysulfone/NMP/Alcohol and CPVC/THF/Alcohol, respectively. Time dependence of the position of the light scattering maximum was observed at polysufone dope solutions, confirming spinodal secomposition (SD). while CPVC dope solutions showed a decreased scattered light intensity with a increased q-valuel, indicating nucleation & growth (NG). For the each system, domain growth rate in the intermediate and late stage of phase separation decreased with increasing the number of carbon of alcohol used as additive (non-solvent). Also, in the early stage for SD, the scattering intensity with time was in accordance with Cahns linear theory of spinodal decomposition,[1-3] regardless of types of non-solvent additive.

• Fashion & Textile Research Journal
• /
• v.14 no.3
• /
• pp.472-477
• /
• 2012

The conditions of wet spinning were considered in order to prepare the fine denier of acrylic fiber. Polyacrylonitrile copolymer was synthesized by the copolymerization of acrylonitrile (AN) and methyl acrylate (MA) initiated by an aqueous sulfite-chlorate redox system. Acrylic fiber was manufactured through wet-spinning in a dimethyl formamide (DMF) system. The conditions of wet-spinning were investigated by i-value, spinning speed, diameter of spinneret, draw ratio, water content of spinning dope and morphology of protofiber. The physical properties of fibers were investigated by Instron. In this experiment, the minimum i-value decreased with the decreasing spinneret diameter, an increased spinning speed, and an increased coagulation bath (CBC) concentration. The maximum draw ratio increased with an increased CBC. The optimum CBC and water content of the spinning dope were 60%-65% and 3.5%, respectively. The tenacity at the breaking point increased with a decreased fineness of fiber. The elongation at breaking point was almost the same value as a function of the fineness of fiber.

• Membrane Journal
• /
• v.24 no.3
• /
• pp.240-248
• /
• 2014

Porous PVDF hollow fiber membranes were prepared by hybrid process of TIPS(thermally induced phase separation) and stretching for membrane distillation. The tests were conducted to investigate that permeability of the membrane could be enhanced by reducing membrane wall thickness. During fiber spinning, dope discharge rate from nozzle was reduced and flow rate of bore fluid increased to make the wall thickness thinner. As dope discharge rate from nozzle was reduced and flow rate of bore fluid increased, the membrane wall thickness was reduced. As a result, air permeability, water permeability and vapor permeability of the membranes increased.

• Journal of Pharmaceutical Investigation
• /
• v.28 no.2
• /
• pp.93-98
• /
• 1998

We have developed liposomes which can be easily prepared with inexpensive lipid, have enhanced stability, and can efficiently deliver DNA into the COS-l cells, Liposome formulations were prepared using cationic materials such as dimethyldioctadecyl ammonium bromide (DDAB), cetyltrimethyl ammonium bromide(CTAB), We investigated the effect of cationic liposome formulations on in vitro DNA transfection, DDAB-containing liposomes showed increased transfection efficiency which was 3.2-fold as much as that by $Lipofectin^{\circledR}$, but CTAB-containing liposomes were inactive in gene transfection. The effect of colipid of DDAB-containing liposome was also investegated. As a colipid, dioleylphosphatidylethanolamine(DOPE) and cholesterol did altered the transfection efficiency of DDAB-containing liposomes. And increased DDAB concentration lowered the transfection efficiency. The optimum amount of liposomal formulation was $10\;{\mu}M$ for $1\;{\mu}g$ of DNA. In the experiment of stability, DOPE-containing liposomes formulation showed a broad size distribution and separation of two major peaks on a 5th day of preparation, but liposomes containing cholesterol was stable for 10 days. DDAB-containing liposomal DNA delivery system was prepared easily and was stable.

• Applied Biological Chemistry
• /
• v.34 no.4
• /
• pp.353-359
• /
• 1991

As a tool for the texture analyses of the soyprotein fibers, the scanning electron microscopical microstructure were studied. With the results of TPA(Texture Profile Analysis), microstructural analyses of the soyprotein fibers showed that the disulfide and hydrogen bonds are one of the most important factors determining the shape and maintenance of fiber struture. The microstructures of the hydrated soyprotein dispersion and dope, as starting materials of the soyprotein fiber were presented.

• Proceedings of the Korean Fiber Society Conference
• /
• 1987.06b
• /
• pp.11-11
• /
• 1987

Among other poly(4,4'-terephthanilidealkylamide)s (PTAA's), poly (4,4'-terephthanilideadipamide) (PTAd) gave clear critical concentration curves. For PTAA's with methylene units more than 6, the critical concentration (C*) seemed to be beyond the solubility limit of H₂SO₄. Under shearing conditions, the nematic domains were easily oriented and stretched in the direction of shear , and a fibrillar structure resulted. At low frequencies, a monotollous reduction of loss tangent (tan) was observed as concentration increased. At high frequencies, however, tan was increased above C* again, and showed maximum at saturation concentration (Cs). With increasing temperature, viscosity of isotropic and anisotropic phases was normally decreased, while viscosity of biphases was increased. Plot of complex viscosity (If) against temperature based on rheological measurements exhibited a good correlation with phase diagram constructed by polarizing microscope observations. Rheological parameters suggested the optimum dope concentration of PTAd with inherent viscosity 2.02 at 30oc is in the vicinity of 19.2 wt%, which seemed to agree well with spinning experiments (around 19.4 wt%). In general, effects of spinning and annealing conditions on the mechanical properties of PTAA fibres were most pronounced in PTAd fibre spun from anisotropic spinning dope .

• Korean Membrane Journal
• /
• v.6 no.1
• /
• pp.61-69
• /
• 2004

Small angle light scattering (SALS) and field emission scanning electron microscope (FE-SEM) have been used to investigate the effects of alcohol on phase separation of chlorinated poly(vinyl chloride) (CPVC)/tetrahydrofuran (THF)/alcohol (9/61/30 wt%) solution during water vapor induced phase separation. A typical scattering pattern of nucleation & growth (NG) was observed for all casting solutions of CPVC/THF/alcohol. In the case of the phase separation of CPVC dope solution containing 30 wt% ethanol or n-propanol, the demixing with NG was observed to be heterogeneous. Meanwhile, the phase separation of CPVC dope solution with 30 wt% n-butanol was found to be predominantly homogeneous NG. Although the different phase separation behavior of NG was observed with types of alcohol additives, the resultant surface morphology had no remarkable differences. That is, even though the NG process by water vapor is either homogeneous or heterogeneous, this difference does not play a main role on the final surface morphology. However, it was estimated from the result of hydraulic flux that the phase separation by homogeneous NG provided the membrane geometry with lower resistance in comparison with that by heterogeneous one.

• Archives of Pharmacal Research
• /
• v.27 no.7
• /
• pp.797-805
• /
• 2004

LPD vectors are non-viral vehicles for gene delivery comprised of polycation-condensed plasmid DNA and liposomes. Here, we described a novel anionic LPD formulation containing protamine-DNA complexes and pH sensitive liposomes composed of DOPE and cholesteryl hemisuccinate (Chems). Central composite design (CCD) was employed to optimize stable LPD formulation with small particle size. A three factor, five-level CCD design was used for the optimization procedure, with the weight ratio of protamine/DNA ($X_1$), the weight ratio of Chems/DNA ($X_2$) and the molar ratio of Chems/DOPE in the anionic liposomes ($X_3$) as the independent variables. LPD size ($Y_1$) and LPD protection efficiency against nuclease ($Y_2$) were response variables. Zeta potential determination was utilized to define the experimental design region. Based on experimental design, responses for the 15 formulations were obtained. Mathematical equations and response surface plots were used to relate the dependent and independent variables. The mathematical model predicted optimized $X_1-X_3$ levels that achieve the desired particle size and the protection efficiency against nuclease. According to these levels, an optimized LPD formulation was prepared, resulting in a particle size of 185.3 nm and protection efficiency of 80.22％.

• Membrane Journal
• /
• v.21 no.1
• /
• pp.62-71
• /
• 2011

Highly enriched oxygen is used in energy-efficient combustion due to decreased non-flammable nitrogen, while high purity nitrogen is used for explosion proof in the LNG ships and keeping the freshness of green stuffs. Membrane technology can be used in these $O_2$ and $N_2$ generation with low energy consumption. In this study, PES was used as a membrane material and 1-methyl-2-pyrollidone (NMP) and acetone were employed as a good solvent and nonsolvent addictive (swelling agent to PES), respectively. Dope solutions were prepared by changing the content of acetone (0, 6.5, 15, 25, 31.5 wt%) in 37 wt% PES solutions. Hollow fiber spinning was performed at 0~10 cm of air-gap distances for each dope solution. $O_2/N_2$ selectivity and permeability were investigated by comparing of hollow fibers coated or not by silicons. $O_2/N_2$ selectivity increased and permeance of $O_2$ and $N_2$ decreased with increasing air-gap height independently of acetone addictions. Optimized PES hollow fibers were obtained with 37/6.5/56.5 wt% PES/acetone/NMP dope solution and 10 cm air-gap, which showed 7.3 of $O_2/N_2$ selectivity and 4.3 GPU of $O_2$ permeability after silicon coating.

• The Korean Journal of Ceramics
• /
• v.2 no.4
• /
• pp.188-192
• /
• 1996

Diamond based electronic devices promise to exhibit unique properties. In order to realize devices diamond has to be doped to render it electrically conductive. In the present work the doping of diamond and of polycrystalline CVD diamond films are reviewd with particular emphasis to ion-implantation doping and to attempts to dope diamond by in-diffusion of the dopants. The quest for finding ways to obtain n-type conductivity in diamond will be critically examined.