• 설비공학논문집
• /
• 제20권3호
• /
• pp.197-204
• /
• 2008

DMFC(Direct Methanol Fuel Cell) is one of promising candidates for power sources of small mobile IT devices like notebook, cell phone, and so on. Efficient operation of fuel cell system is very important for long-sustained power supply because of limited fuel tank size. It is necessary to investigate operation characteristics of fuel cell stack for optimal control of DMFC system. The generated voltage was modeled according to various operating condition; methanol concentration, stack temperature, and load current. It is inevitable for methanol solution at anode to cross over to cathode through MEA(membrane electrode assembly), which reduces the system efficiency and increases fuel consumption. In this study, optimal operation conditions are proposed by analyzing stack performance model, cross-over phenomenon, and system efficiency.

• 전기화학회지
• /
• 제11권1호
• /
• pp.16-21
• /
• 2008

직접메탄올 연료전지 (DMFC)의 핵심 구성 요소 중에서 하나는 고분자 전해질막과 촉매층 (연료극과 공기극)으로 구성된 전해질/전극 접합체 (MEA)이다. 그중에서 촉매층은 브러싱법, 전시법, 스프레이 코팅법, 스크린 프린팅법과 같은 다양한 방법을 사용하여 carbon paper나 carbon cloth등과 같은 전극 지지체 위에 코팅한다. 그러나 이러한 촉매 코팅방법들은 전극 지지체 위에 촉매를 균일한 두께로 코팅하기 어렵고, 촉매의 손실이 많으며, 또한 코팅 시간이 많이 필요하다는 단점들이 있다. 본 연구에서는 DMFC용 MEA의 전극층을 바코팅 방법 (bar-coating method)을 사용하여 한 번에 원하는 양의 촉매가 코팅되도록 제조하였다. 이렇게 제조한 전극 촉매층 표면과 단면의 형태를 SEM을 사용하여 관찰하였다. 제조한 MEA의 성능과 저항은 단위전지와 임피던스 분석기를 사용하여 측정하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 제17회 워크샵 및 추계학술대회
• /
• pp.662-662
• /
• 2005

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 2004년도 수소연료전지공동심포지움 2004논문집
• /
• pp.65-70
• /
• 2004

• 한국수소및신에너지학회논문집
• /
• 제19권6호
• /
• pp.467-473
• /
• 2008

This study is to investigate the influence of catalyst loading quantity on the direct methanol fuel cell (DMFC) performance. In this paper, Pt-Ru and Pt-black loading as the catalyst were varied from 1 to $4mg/cm^2$ at the anode and cathode, respectively. The experiment was conducted with single fuel cell consisted of $5cm^2$ effective electrode area, serpentine type flow pattern and Nafion 117 membrane. Also, AC impedance and methanol crossover current were measured to investigate the performance loss precisely. As a result, the performance of fuel cell was significantly increased with the increase of cathode catalyst loading. However, the performance did not increase further above a certain Pt-Ru catalyst loading as the increase of anode catalyst loading.

• 전기화학회지
• /
• 제6권1호
• /
• pp.68-71
• /
• 2003

전지 성능을 저하시키지 않고 연료극 및 공기극의 귀금속 촉매량을 줄이기 위하여 다층막 전극을 이용한 직접메탄을 연료전지의 성능특성을 조사하였다. 다층막 전극 즉, 연료극과 공기극에 사용된 촉매사용량과 나피온 막의 종류를 변화시키며 최종성능을 측정하였다 본 실험에서 사용된 촉매량은 연료극이 $3-4mg/cm^2$ 공기극이 $1-2mg/cm^2$이다. 본 실험에서는 나피온 115를 사용한 MEA3의 $90^{\circ}C$, 2기압에서 측정 결과 최대 전력밀도인 $230mW/cm^2$를 나타내었다. 이 결과는 현재 시판되고 있는 상용전극과 거의 같은 수준의 성능을 보여주고 있는 반면, 금속 촉매의 양은 기존의 상용전극과 비교하여 약 $50\%$ 정도 감소된 것이다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.171-171
• /
• 2009

The electrodes are usually made of a porous mixture of carbon-supported platinum and ionomers. $SnO_2$ particles provide as supports that have been used for DMFCs, and it have high catalytic activities toward methanol oxidation. The main advantage of $SnO_2$ supported electrodes is that it has strong chemical interactions with metallic components. The high activity to a synergistic bifunctional mechanism in which Pt provides the adsorption sites for CO, while oxygen adsorbs dissociative on $SnO_2$. The reaction between the adsorbed species occurs at the Pt/$SnO_2$ boundary. The morphological observations were characterized by FESEM and transmission electron microscopy (TEM). $SnO_2$ particles crystallinity was analyzed by the X-ray diffraction (XRD). The surface bonded state of the $SnO_2$ particles and electrode materials were observed by the X-ray photoelectron spectroscopy (XPS). The electric properties of the Pt/$SnO_2$ catalyst for methanol oxidation have been investigated by the cyclic voltametry (CV) in 0.1M $H_2SO_4$ and 0.1M MeOH aqueous solution. The peak current density of methanol oxidation was increased as the $SnO_2$ content in the anode catalysts increased. Pt/$SnO_2$ catalysts improve the removal of CO ads species formed on the platinum surface during methanol electro-oxidation.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.185-185
• /
• 2006

The performances of proton exchange membrane fuel cell (PEMFC), direct formic acid fuel cell (DFAFC) and direct methanol fuel cell (DMFC) with sulfonated poly(ether sulfone) membrane are reported. Pt/C was coated on the membrane directly to fabricate a MEA for PEMFC operation. A single cell test was carried out using $H_2/air$ gases as fuel and oxidant. A current density of $730\;mA/cm^2$ at 0.60 V was obtained at $70^{\circ}C$. Pt-Ru (anode) and Pt (cathode) were coated on the membrane for DMFC operations. It produced $83\;mW/cm^2$ of maximum power density. The sulfonated poly(ether sulfone) membrane was also used for DFAFC operation under several different conditions. It showed good cell performances for several different kinds of polymer electrolyte fuel cell applications.

• 전기화학회지
• /
• 제11권1호
• /
• pp.11-15
• /
• 2008

The composite membrane for direct methanol fuel cell (DMFC) was developed using $H_3O^+-{\beta}"-Al_2O_3$ powder and perfluorosulfonylfluroride copolymer (Nafion) resin. The perfluorosulfonylfluroride copolymer (Nafion) resin was mixed with $H_3O^+-{\beta}"-Al_2O_3$ powder and it was made to sheet form by hot pressing. The electrodes were prepared with 60 wt% PtRu/C and 60wt% Pt/C catalysts for anode and cathode, respectively. The morphology and the chemical composition of the composite membrane have been investigated by using SEM and EDXA, respectively. The composite membrane and $H_3O^+-{\beta}"-Al_2O_3$ were analyzed by using FT-IR and XRD. The methanol permeability of the composite membranes was also measured by gas chromatography (GC). The performance of the MEA containing the composite membrane (2wt% $H_3O^+-{\beta}"-Al_2O_3$) was higher than that of normal pure Nafion membrane at high operating temperature (e.g. $110^{\circ}C$), due to the homogenous distribution of $H_3O^+-{\beta}"-Al_2O_3$, which decreased the methanol permeability through the membrane and enhanced the water contents in the composite membrane.

• 전기화학회지
• /
• 제11권1호
• /
• pp.1-5
• /
• 2008

A Pt-layer was deposited on the anode side of a Nafion membrane via a sputtering method in order to reduce methanol crossover in a direct methanol fuel cell (DMFC). The methanol permeation and the proton conductivity through the modified membranes were investigated. The performances of the direct methanol fuel cell were also tested using single cells with a Nafion membrane and the modified membranes. The Pt-layers on the membrane blocked both methanol crossover and proton transport through the membranes. Methanol permeability and proton conductivity decreased with an increase of the platinum layer thickness. At methanol concentration of 2 M, the DMFC employing the modified membrane with a platinum layer of 66 nm-thickness showed similar performance to that of a DMFC with a bare Nafion membrane in spite of the lower proton conductivity of the former. The maximum power density of the cell using the modified membrane with a platinum layer of 66 nm-thickness increased slightly while that of the cell with the bare membrane decreased abruptly when a methanol solution of 6M was supplied.