• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.8
• /
• pp.1010-1015
• /
• 2012

DME(Dimethyl ether) is the one of the massive energy sources synthesized from natural gas. KOGAS has already developed the commercial-scale production plant of DME and has been doing to obtain overseas resources to meet the domestic needs. This paper presents the DME storage tank design criteria by stress and strain analysis, and the experimental study on the evaporation phenomena of DME by thermal intake and physical rolling movement of DME FPSO or cargo vessel, because the various moving motions along with heat intake cause the evaporation of low temperature liquid. The experimental result shows that the evaporation rate was increased with larger rolling degree and higher liquid level. The rolling motion leads to evaporate about 20% increase with 15 degree rolling based on the evaporation quantity without rolling.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.1
• /
• pp.99-106
• /
• 2013

DME (Di-Methyl Ether) is synthetic product that is produced through dehydration of methanol or a direct synthesis from syngas. And it is able to save fossil fuel and reduce pollutants of emission such as PM and $CO_2$. In spite of its advantages it is difficult to design DME fuelled engine system because DME fuel may cause to severely generate cavitation and corrosion in fuel delivery system due to physical properties of DME. Therefore, in this study three-dimensional internal flow characteristics with consideration of cavitation were predicted in the DME injector using diesel and DME fuel. Moving grid technique was employed to describe needle motion and 1-D hydraulic simulation of injector was also simulated to obtain transient needle motion profiles. The results of simulation show that cavitations was generated at the inlet of nozzle near high velocity region both diesel and DME. And mass flow rate of DME is reduced by 4.73% compared to that of diesel at maximum valve lift because cavitation region of DME is much more larger. To increase flow rate of DME injector, internal flow simulation has been conducted to investigate the nozzle hole inner R-cut effect. The flow rates of diesel and DME increase as R-cut increases, and flow coefficient of DME fuel injector was increased by 6.3% on average compared with diesel fuelled injector. Finally, optimum shape of DME injector nozzle is suggested through the comparison of flow coefficient with variation of nozzle hole inner R-cut.

• Korean Chemical Engineering Research
• /
• v.50 no.3
• /
• pp.464-470
• /
• 2012

To study characteristics of DME and Propane blended fuel in mixing drum as time passed, mixing experiment of two components was performed. After 20 wt% of DME and 80 wt% of Propane were injected into mixing drum sequentially, and the mixture ratio of blended fuel was analyzed at several sampling ports. Consequently, DME and Propane were not easily mixed and DME was sunk to the bottom of the mixing drum by the density difference. The daily rate of DME ingredient increase was 0.2-0.3 wt%, and it took over 500 hours until two of them were mixed uniformly. And after recirculation of blended fuel in mixing drum, DME and Propane were mixed immediately and uniformly.

• Journal of the Korean Institute of Gas
• /
• v.12 no.3
• /
• pp.81-84
• /
• 2008

In this paper, the research was applied the mixture gas of Propane-DME (dimethyl ether) for being commercialization to residential gas ranges. In order to examine a correspondence between Korean Standard and thermal efficiency characteristics at each burner, experiments were performed with 100% Propane and the mixture gas of 80% Propane-20% DME. The experimental results were shown that the higher a mixture ratio of DME was used, the lower a thermal efficiency was gained. Those were due to low caloric value of DME. With 80% Propane-20% DME mixture gas, one of residential gas ranges was not satisfied the condition for the thermal efficiency value, 40%, Korean Standard. Consequently, the research needs about the standard for being commercialization to the mixture gas of Propane-DME.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.792-795
• /
• 2007

본 연구 목적은 석탄 가스화를 통해 얻어진 합성가스를 이용하여 국내에서 개발된 DME 합성 촉매를 사용하여 DME 전환 공정에 대한 특성을 파악하는 것이다. 특히, DME 합성 반응에 가장 큰 영향을 미치는 합성 반응로의 온도 제어를 위하여 thermosyphon 시스템을 개발하여 DME 합성 반응에 최적온도로 알려진 $230{\sim}260^{\cdot}C$ 범위에서 제어가 가능함을 확인 하였다. 석탄 40 kg/h를 공급하였을 때 합성가스 유량은 $80{\sim}100$ $Nm^3/h$ 정도를 얻었다. DME 합성 반응에 사용한 촉매는 합성가스로부터 메탄올을 얻기 위한 촉매와 메탄올의 탈수 촉매(Cu/Zn/Al+r-$Al_2O_3$)를 혼합한 촉매를 사용하였다. DME 합성 반응로의 GHSV(1/kg$^{\cdot}C$cat h)는 $2500{\sim}3000$ 정도이며, 운전 압력 60기압에서 $H_2$ 전환율 $65{\sim}75%$, DME 선택도는 $69{\sim}79%$ 정도를 얻었다.

• Journal of ILASS-Korea
• /
• v.12 no.1
• /
• pp.30-37
• /
• 2007

Dimethyl ether (DME) as an alternative fuel for compression ignition engine was investigated by measuring spray development processes, injection rate profiles, engine performance, and exhaust emission characteristics. The results of DME fueled engine were compared with those obtained by fueled with diesel. The experimental results showed that DME has approximately 0.03ms shorter injection delay and higher maximum injection rate than those of diesel fuel at a constant injection pressure of 50MPa. The spray visualization indicates that DME has shorter spray tip penetration due to its low density and faster evaporation. The combustion characteristics of DME operated engine provided faster ignition delay and three times shorter combustion duration. It is believed that the better evaporation and atomization characteristic of DME contributes the faster combustion. At all operating condition, soot emission was not detected due to the clean combustion of DME.

• Journal of Positioning, Navigation, and Timing
• /
• v.10 no.2
• /
• pp.113-120
• /
• 2021

The Distance Measuring Equipment (DME) is a ground-based aircraft navigation system and is considered as an infrastructure that ensures resilient aircraft navigation capability during the event of a Global Navigation Satellite System (GNSS) outage. The main problem of DME as a GNSS back up is a poor positioning accuracy that often reaches over 100 m. In this paper, a novel approach of applying deep reinforcement learning to a DME pulse design is introduced to improve the DME distance measuring accuracy. This method is designed to develop multipath-resistant DME pulses that comply with current DME specifications. In the research, a Markov Decision Process (MDP) for DME pulse design is set using pulse shape requirements and a timing error. Based on the designed MDP, we created an Environment called PulseEnv, which allows the agent representing a DME pulse shape to explore continuous space using the Soft Actor Critical (SAC) reinforcement learning algorithm.

• Journal of the Korean Society of Combustion
• /
• v.18 no.1
• /
• pp.27-33
• /
• 2013

Hydrogen-dimethy ether(DME) partially premixed compression ignition(PCCI) engine combustion was investigated in a single cylinder compression ignition engine. Hydrogen and DME were used as low carbon alternative fuels to reduce green house gases and pollutant. Hydrogen was injected at the intake manifold with an injection pressure of 0.5 MPa at fixed injection timing, $-210^{\circ}CA$ aTDC. DME was injected directly into the cylinder through the common-rail injection system at injection pressure of 30 MPa. DME inejction timing was varied to find the optimum PCCI combustion to reduce CO, HC and NOx emissions. When DME was injected early, CO and HC emissions were high while NOx emission was low. As the DME injection was retarded, the CO and HC emissions were decreased due to high combustion efficiency. NOx emissions were increased due to the high in-cylinder temperature. When DME were injected at $-30^{\circ}CA$ aTDC, reduction of HC, CO and NOx emissions was possible with high value of IMEP.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.16 no.3
• /
• pp.301-306
• /
• 2010

DME(Di-Methyl Ehter, $CH_3OCH$) is currently attracting worldwide attention due to its environmentally friendly characteristics. Until now it was researched as a major alternative fuel of diesel automobile because it is a clean fuel producing low soot. Therefore, in this study, in order to investigate the effect of DME mixing on number density and size of soot particle, DME has been mixed in opposed-flow ethylene diffusion flame with the mixture ratios 5%, 14% and 30%. A laser extinction/scattering technique has been adopted to measure the volume fraction, number density, and size of soot particles. The experimental results showed that the soot concentration of mixture flames with the mixture ratios 5% and 14% produces soot more, even though that of 30% was decreased. This means that even though DME has been known to be a clean fuel for soot formation, the mixing of DME in diffusion flame of ethylene, where acetylene maintains high concentration in soot formation regions, could produce enhanced production of soot.

• Journal of the Korean Institute of Gas
• /
• v.12 no.3
• /
• pp.7-12
• /
• 2008

In this study, a spark ignition engine operated with the DME blended LPG fuel was investigated experimentally. Performance, emissions characteristics including hydrocarbon, CO, NOx, and combustion stability of an SI engine fuelled with DME blended LPG fuel were examined at $1200{\sim}5200\;rpm$. Results showed that stable engine operation was possible for a wide range of engine loads within 20% mass content of DME fuel. Also, engine output power within 10% mass content of DME fuel was comparable to that of pure LPG fuel operation. However, engine output power was decreased and break specific fuel consumption (BSFC) was severely increased with the amount of blended fuel as the energy content of DME was much lower than that of LPG. DME blended LPG fuel is expected to be potential for enlarging DME market.