• Korean Journal of Materials Research
• /
• v.33 no.4
• /
• pp.124-129
• /
• 2023

This study assessed the influences of fluorine introduced into DLC films on the structural and mechanical properties of the sample. In addition, the effects of the fluorine incorporation on the compressive stress in DLC films were investigated. For this purpose, fluorinated diamond-like carbon (F-DLC) films were deposited on cobalt-chromium-molybdenum substrates using radio-frequency plasma-enhanced chemical vapor. The coatings were examined by Raman scattering (RS), Attenuated total reflectance Fourier transform infrared spectroscopic analysis (ATR-FTIR), and a combination of elastic recoil detection analysis and Rutherford backscattering (ERDA-RBS). Nano-indentation tests were performed to measure hardness. Also, the residual stress of the films was calculated by the Stony equation. The ATR-FTIR analysis revealed that F was present in the amorphous matrix mainly as C-F and C-F₂ groups. Based on Raman spectroscopy results, it was determined that F made the DLC films more graphitic. Additionally, it was shown that adding F into the DLC coating resulted in weaker mechanical properties and the F-DLC coating exhibited lower stress than DLC films. These effects were attributed to the replacement of strong C = C by feebler C-F bonds in the F-DLC films. F-doping decreased the hardness of the DLC from 11.5 to 8.8 GPa. In addition, with F addition, the compressive stress of the DLC sample decreased from 1 to 0.7 GPa.

• Journal of the Korean Society for Heat Treatment
• /
• v.31 no.2
• /
• pp.63-67
• /
• 2018

Recent mold industry uses many roll-to-roll processes that can produce high production speed and precision machining and automation process. In the circular cylinder mold, however, patterns of less than $10{\mu}m$ are difficult to manufacture and maintain. In this study, we fabricated a circular cylindrical mold with a DLC thin film which have high hardness, low coefficient of friction and high releasability by using lithography and lift-off process. The height, line width, and pitch of the fabricated DLC macro pattern are $3.1{\mu}m$, $9.1{\mu}m$ and $20.2{\mu}m$, respectively. The pattern size is finer than the current applied to the aluminum cylinder type, and this shows the possibility of practical use of DLC micro pattern roll mold.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1393-1395
• /
• 2001

DLC films are deposited by using a modified FCVA system. Carbon amorphous network, surface roughness, internal compressive stress, resistivity, and Hall mobility are studied as a function of nitrogen flow rate (0 $\sim$ 10 sccm). As the nitrogen content is increased in the carbon network, the size of $sp^2$ clusters is increased, the internal compressive stress is decreased, and the resistivity is remarkably decreased. The RMS values of the surface roughness are measured to be in the range of 0.2$\sim$0.5nm. The Hall mobility of DLC film with 3 sccm of nitrogen added is 3.22 $cm^2/V{\cdot}$s.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.121-121
• /
• 2013

수소로 희석된 벤젠 가스를 반응 가스로 이용하여 합성된 DLC 박막의 마찰 마모 특성을 평가하기 위하여, 일반 대기 환경 및 수중 환경에서 마모 실험을 수행하였다. 일반 대기 환경에서는 박막의 기계적 특성, 마찰 계수 및 마모 거동이 거의 변화하지 않았다. 반면, 수중 환경에서는 마찰 계수가 대기 환경에서보다 안정적으로 평가되었다. 이는 DI-water가 윤활제(lubricant) 역할을 하기 때문으로 예측된다. 또, 수중 환경에서의 마모 실험 결과, 수소가 희석되지 않은 반응 가스를 이용하여 증착 된 DLC 박막의 경우, delamination wear가 상대적으로 많이 관찰되었다. 하지만, 반응 가스에 희석 된 수소량이 증가함에 따라서, 이런 delamination wear가 현저하게 억제됨을 관찰하였다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2003.10a
• /
• pp.59-59
• /
• 2003

In recent, various functional coatings on artificial tooth implants have been conducted to enhance the bonding strength between implants and bones. Despite of these efforts, some previous reports argued that an adhesion strength between titanium implant and the final coatings like hydroxyapatite(HA) is weaker than the strength between coating and bone. In order to increase the adhesion force between the final coating and implant surface, TiN/DLC based functionally graded coating, which has higher mechanical strength than the titanium implant, was applied as a middle layer between titanium implant and final coating. Particularly we finally coated a biocompatible hydroxyapatite film on the DLC layer and examined the mechanical properties. As a result, TiN/DLC based functionally graded coating showed the higher adhesion strength compared with hydroxyapatite single layer coating on the titanium implant.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.397-397
• /
• 2007

Diamondlike carbon (DLC) coatings were deposited on alumina ceramic seals using a plasma immersion ion deposition technique (PIID). Then they were subjected to tribological tests using a pin-on-disc tribometer under a high load (1.3 GPa) and under elevated temperatures up to 400C. Coefficients of friction (COFs) were recorded and compared with that of the untreated alumina while the wear tracks were analyzed using SEM with EDS to characterize the DLC films. To enhance the DLC adhesion to the substrate, various interlayers including Si and Cr were deposited using the PIID process or an ion beam assisted deposition (IBAD) method. It was observed that the DLC coating, if adhering well to the substrate, reduced the COFs significantly, from 0.4-0.8 for the uncoated alumina to about 0.05-0.1, within the tested temperature range. The adhesion was determined by the interlayer type and possibly by the application method. Cr interlayer did not perform as well as the Si interlayer. This could also be due to the fact that the Cr interlayer and the subsequent DLC coating had to be done in two different processing systems, while both the Si interlayer and the subsequent DLC film were deposited in one system without breaking the chamber. The coating failure mode was found to be delamination between the Cr and the alumina substrate. In contrast, the Si interlayer with proper DLC deposition procedures resulted in very good adhesion and hence excellent tribological performance. Further study may lead to future DLC applications of ceramic seals.

• Journal of Korean Vacuum Science & Technology
• /
• v.3 no.1
• /
• pp.54-58
• /
• 1999

We deposited diamond-like carbon (DLC) films using ion beam sputtering of a graphite target on flat substrates for use as a thin film field emitter. An n-type silicon wafer, titanium-coated silicon, and indium tin oxide (ITO) coated glass were used as a substrate. All films exhibited a sudden increase in the emission after a breakdown occurred at high voltage. The morphology of the films after the breakdown depended on the substrate. On ITO and Ti substrates, the DLC film peeled off upon breakdown, but on the Si substrate the surface melting due to breakdown resulted in the formation of various structures such as a sharp point, mound, and crater. By scanning the deformed surface with a tip anode, we found that the emission was concentrated at the deformed sites, indicating that the field enhancement due to the morphology change was responsible for the increased emission.

• Korean Journal of Materials Research
• /
• v.11 no.7
• /
• pp.550-555
• /
• 2001

A diamond-like carbon(DLC) films were deposited on the borosilicate glass substrate by radio frequency plasma enhanced chemical deposition(rf-PECVD). The $methane(CH_4)-hydrogen(H_2)$ gas mixture was used as precursor gas. The morphologies, the structure and the optical properties of the DLC films were investigated by SEM, Raman and UV spectrometer. The deposition rate was slightly increased with the hydrogen concentration in the gas mixture and it maintained constant at over 25 sccm of the gas flow rate. The optical band gap calculated by UV spectra decreased with increase of deposition time and DC self bias, but that were not effected by hydrogen content. Most effective parameter on the transmittance of film was bias voltage, especially in the range of ultra violet and visible light.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.333-334
• /
• 2007

Diamond-like carbon (DLC)박막은 높은 경도, 화학적 안정성, 높은 광 투과성을 가지고 있어, 공구강, 광학렌즈 및 플라스틱의 보호 코팅을 위해 응용되어진다. 본 연구에는 DLC 박막은 Silicon을 기반으로 하는 태양전지 반사 반지막으로 응용을 위해, 13.56 MHz RF 플라즈마 화학기상 증착 (RF-PECVD)법을 통해 합성되었다. DLC 합성 시 RF power는 150 W, 메탄 (CH4)가스의 유량은 6%~10% 조절되었다. 합성되어진 DLC 박막의 광학적 특성은 UV spectrometry, Ellipsometry를 사용하여 분석되었고, 경도는 Nano-indenter를 사용하여 측정되었다. 측정 결과 투과도와 굴절률 등의 광학적 특성은 탄소 조성비가 6%정도에서 가장 좋은 결과 값을 얻었으나, 물리적 특성인 경도는 탄소 조성비가 높을수록 증가하는 경향을 보였으며, Si기판과의 접착력은 32N 이상의 높은 값을 나타내었다. 결과로써, DLC 박막은 합성시 적절한 탄소 조성비를 통해 silicon을 기반으로 하는 태양전지 반사방지막으로 응용할 수 있다.

• The monthly packaging world
• /
• s.144
• /
• pp.111-113
• /
• 2005