• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.26-31
• /
• 2006

An experimental investigation of an early injection strategy was conducted on a small single cylinder common-rail DI diesel engine to reduce the oxides of nitrogen($NO_x$) emission. The main objectives of this study were to investigate the emissions, performance and combustion characteristics in a diesel engine with early and two-stage injections. The two- stage injection was conducted to reduce the wall-wetting of early injected fuels on the cylinder wall or to promote the ignition of premixed charge. The engine test was performed at conditions of 1500rpm, injection timing ranging from TDC to BTDC $80^{\circ}$. The experimental results show that $NO_x$ emissions were decreased in both cases of early injection and two stage injection compared to the conventional diesel combustion by the near TDC injection. However, soot and products of incomplete products (i.e. HC and CO) are slightly increased. Also, the second injection near TDC promoted the ignition of premixed fuel, therefore, IMEP was increased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.3
• /
• pp.390-401
• /
• 2000

In this study, numerical calculation is carried out to investigate the influence of injection timing, fuel amount, intake $O_2$ concentration, and EGR on Nitric Oxide(NO) formation using a two-zone model in a diesel engine. Results can be summarized as follows. The NO formation is very sensitive to the burned gas temperature, so multi-zone model must be applied to combustion process to predict the burned gas temperature exactly. Since the burned gas temperature increases rapidly during the premixed combustion, most NO is formed within 20 crank angle degrees after ignition. As the injection timing is retarded, the combustion occurs later in the expansion process which causes the decrease of burned gas temperature and, as a result, NO formation decrease. The increase of fuel amount results in the increase of earlier formation of NO in the engine. As the intake $O_2$ concentration increases, the maximum pressure and burned gas temperature increase due to activate combustion. And, [O] mole fraction of equilibrium combustion products also increase. Therefore NO exponentially increases. If exhaust gas is recirculated, the burned gas temperature decreases which results in NO decrease. If exhaust gas is cooled, more NO can be decreased.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.54-62
• /
• 2007

The knock characteristics in an engine were investigated under homogeneous charge compression ignition (HCCI) operation. Liquefied petroleum gas (LPG)and gasoline were used as fuels and injected at the intake port using port fuel injection equipment. Di-methyl ether (DME) was used as an ignition promoter and was injected directly into the cylinder near compression top dead center (TDC). A commercial variable valve timing device was used to control the volumetric efficiency and the amount of internal residual gas. Different intake valve timingsand fuel injection amounts were tested to verify the knock characteristics of the HCCI engine. The ringing intensity (RI) was used to define the intensity of knock according to the operating conditions. The RI of the LPG HCCI engine was lower than that of the gasoline HCCI engine at every experimental condition. The indicated mean effective pressure (IMEP) dropped when the RI was over 0.5 MW/m2and the maximum combustion pressure was over 6.5MPa. There was no significant relationship between RI and fuel type. The RI can be predicted by the crank angle degree (CAD) at 50 CA. Carbon monoxide (CO) and hydrocarbon (HC) emissions were minimized at high RI conditions. The shortest burn duration under low RI was effective in achieving low HC and CO emissions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.3
• /
• pp.9-18
• /
• 1995

The substitution of conventional fuel oil by alternative fuels is of immense interest due to liquid oil shortage and requirements of emission control standard. Among the alternative fuels, natural gas may be the most rational fuel, because of its widespread resource and clean est burning. Meanwhile, engine simulation is of great importance in engine development. Hence a zero-dimensional combustion model was developed for dual-fuel system. Natural gas was injected directly into the cylinder and small amount of distillate was used to provide the ignition kernel for natural gas burning. The intake air and exhaust gas flow was modeled by filling and emptying method. Although the single zone approach has an inherent limitation, the model showed promise as a predictive tool for engine performance. Its simulation was also made to see how the engine performance was influenced by the fuel injection timings and amount of each fuel.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.3
• /
• pp.394-403
• /
• 2008

The effects of water injection (WI) and urea injection for NOx on a 4-cylinder Direct Injection (DI) diesel engine were investigated experimentally. For water injection, it was installed at the intake pipe and the water quantity was controlled at the intake manifold and Manifold Air Flow (MAF) temperatures while the urea injection was located at the exhaust pipe and the urea quantity was controlled by NOx quantity and MAF. The effects of WI system, urea-SCR system and the combined system were investigated with and without exhaust gas recirculation (EGR). Several experiments were performed to characterize the urea-SCR system, using engine operating points of varying raw NOx emissions. The results of the Stoichiometric Urea Flow (SUF) and NOx map were obtained. In addition, NOx results were illustrated according to the engine speed and load. It is concluded that the NOx reduction effects of the combined system without the EGR were better than those with the EGR-based engine.

• 연구논문집
• /
• s.29
• /
• pp.29-38
• /
• 1999

In comparison with gasoline engine, LPG direct injection engine has some advantages not only in emission and fuel efficiency but also in prevention of power decrease and back fire etc. which are disadvantages of conventional LPG engine. In this study, comparision tests of the incylinder spray and combustion characteristics between of LPG and gasoline fuels were performed in the RCEM as a basic research for the development of future LPG engine with low emission and high fuel efficiency During the direct injection of LPG fuel and gasoline into the inside of RCEM, spray development characteristics according to the injection condition have been photographed by the high speed shadow graph methods. The conditions for the optimum mixture distribution of LPG and gasoline fuels are achievable at the selected ignition timing, respectively.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.9-15
• /
• 2004

The characteristics of combustion and emissions were investigated in a single cylinder DI diesel engine equipped with a common rail injection system. This study presents an experimental study of the effect of engine speed, injection timing, injection pressure and pilot injection timing on the combustion and exhaust emissions. The engine speeds were 1000 and 2000rpm and the corresponding injection pressures were 50 and 100MPa. Experimental results show that NOx emissions decrease with retarded injection timing, while HC and CO emissions increases. Higher injection pressure increases NOx with lower soot emissions. For the case with the pilot injection prior to main injection, the ignition delay is shortened and the premixed combustion ratio decreases. Also NOx and soot emissions are decreased with increase of pilot injection advance.

• Journal of ILASS-Korea
• /
• v.26 no.2
• /
• pp.81-87
• /
• 2021

This study was performed to calculate the swirl ratio of a diesel engine intake port by a 1D computer simulation under actual engine operating conditions. The swirl ratio of the intake port was simulated according to the change of the engine speed during the operation of the motoring without fuel injection. The swirl ratio of the intake port was simulated according to changes in the crank angle during the four-cycle operation of intake, compression, expansion and exhaust. The swirl ratio represented by the three regions of the piston, center and squish was simulated. Among the three regions, the piston-region swirl ratio is important for effective air-fuel mixing in the engine cylinder. In particular, it was confirmed during the simulation that the piston swirl ratio before and after the compression top dead center (TDC) point when fuel is injected in the DI diesel engine can have a significant effect on the mixing of air and fuel. It was desirable to set the average piston swirl ratio over a crank angle section before and after compression TDC as the representative swirl ratio of the cylinder head intake port according to the change of the engine speed.

• Journal of Korean Society for Quality Management
• /
• v.48 no.3
• /
• pp.409-420
• /
• 2020

Purpose: The purpose of this study is to develop a measurement scale for evaluating the auditory affect of automobile engine sounds. Methods: In order to collect affective vocabulary, literature review, user tests, and expert interviews were conducted. Affective vocabulary related to automobile engine sounds was selected through three methods. To develop the evaluation scale, open/close card-sorting and expert interview-based survey method was used. Results: The results of this study are as follows; In order to select the main affective vocabulary from the collected vocabulary, 39 vocabularies with a frequency of 5 or higher were selected as vocabulary expressing the main auditory affect of automobile engine sounds. Each affective vocabulary is divided into three di- mensions, it was confirmed that the conceptual model for the auditory affect of automobile engine sounds is composed of three levels: intuitive, descriptive, and evaluative of hierarchical structure. As a result of the study, four indices of intuitive dimension, seven indices of descriptive dimension, and one index of evaluative dimension were derived from the evaluation scale of the auditory affect in an automobile engine sound. Conclusion: The auditory evaluation scale developed in this study can be used to systematically measure and evaluate the auditory affect of automobile engine sounds.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.521-527
• /
• 2005

The effects of an urae injection at the exhaust pipe for a 4-cylinder DI(Direct Injection) diesel engine are investigated experimentally. The urea quantity was controlled by NOx quantity and MAF(Manifold Air Flow). The urea injection must be precisely metered and then I used the urea syringe pump. I have tested 4 kinds of items that were with the EGR base engine and without the EGR engine. Then I tested each urea-SCR(Selective Catalytic Reduction) system. As the results, I can caculate the SUF(Stoichiometric Urea Flow) and visualize the NOx results by variation of engine speed and engine load. Also, I can make the NOx map. Therfore, I knew that NOx reduction effects of the urea-SCR system without the EGR engine were better than the with EGR base engine except of low load and low speed.