• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1542-1545
• /
• 2009

For the application of flexible substrate to future display and new transparent devices, indium tin oxide (ITO) thin film was formed on polycarbonate(PC) substrate at room temperature by in-line sputter system. During the ITO sputtering, Ar and $O_2$ reaction gas were fixed at a constant value and the process pressure was varied from 3 to 7 mtorr. From the electrical and the optical properties of sputtered ITO films, the sheet resistances of as-deposited ITO films varied with a different pressure and the optical transmittances of the ITO films at visible wavelength were maintained above 85%. The results are considered to be due to the saturation of $O_2$ atoms from reaction in ITO film.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.52.2-52.2
• /
• 2011

본 연구의 목적은 CIGS 태양전지의 두 가지 TCO층 중 AZO를 제외한 intrinsic ZnO의 전자빔 처리 영향에 대한 특성 분석을 하고자 함이다. 또한 추후 CIGS 태양전지를 제조하여 적용 시 전자빔 처리 전후의 특성이 어떻게 변하는지를 알아보기 위한 사전 실험이다. Intrinsic ZnO는 RF magnetron sputter 를 이용하여 약 100nm의 두께로 증착 하였다. 이때 공정 압력을 변수로 RF power는 80W로 설정 하였으며 Ar 분압은 10mtorr, 5mtorr, 1mtorr로 각각 달리 하며 증착 하였다. 이후 전자빔 처리를 위해 각각의 시편에 Argon flow 7sccm 상태에서 DC power 3kW, RF power 300W의 세기로 전자빔 처리를 실시 하였다. 전자빔 처리에 따른 전기적, 구조적 특성을 분석하기위해 Hall measurement와 SEM, XRD, UV-vis spectroscopy을 사용하였다. 먼저 Hall measurement 측정을 통한 전기적 분석 결과 비저항이 무한대에서 약 $40m{\Omega}{\cdot}cm$로 감소된 결과를 도출 할 수 있었으며, $2{\sim}3.4{\times}10^{18}/cm^3$ 이상의 carrier density 가 측정 되었다. UV-vis spectroscopy를 이용한 투과도 측정결과 모든 시편에서 Band gap이 감소하는 결과를 보였다. SEM, XRD를 이용한 분석결과 결정성 및 grain의 크기가 증가하는 결과를 얻을 수 있었다.

• Korean Journal of Materials Research
• /
• v.24 no.4
• /
• pp.194-200
• /
• 2014

Metallic Cr film coatings of $1.2{\mu}m$ thickness were prepared by DC magnetron sputter deposition method on c-plane sapphire substrates. The thin Cr films were ammoniated during horizontal furnace thermal annealing for 10-240 min in $NH_3$ gas flow conditions between 400 and $900^{\circ}C$. After annealing, changes in the crystal phase and chemical constituents of the films were characterized using X-ray diffraction (XRD) and energy dispersive X-ray photoelectron spectroscopy (XPS) surface analysis. Nitridation of the metallic Cr films begins at $500^{\circ}C$ and with further increases in annealing temperature not only chromium nitrides ($Cr_2N$ and CrN) but also chromium oxide ($Cr_2O_3$) was detected. The oxygen in the films originated from contamination during the film formation. With further increase of temperature above $800^{\circ}C$, the nitrogen species were sufficiently supplied to the film's surface and transformed to the single-phase of CrN. However, the CrN phase was only available in a very small process window owing to the oxygen contamination during the sputter deposition. From the XPS analysis, the atomic concentration of oxygen in the as-deposited film was about 40 at% and decreased to the value of 15 at% with increase in annealing temperature up to $900^{\circ}C$, while the nitrogen concentration was increased to 42 at%.

• Journal of the Korean Vacuum Society
• /
• v.2 no.4
• /
• pp.474-479
• /
• 1993

Submicron contact hole filling with aluminum alloys has been achieved with a multistep metallization method, which utilizes a metal " flow" or self-diffusion process at elevated temperatures after the metal was sputter-deposited. A multi-chamber, modular sputtering system was employed to deposit aluminum alloys and subsequently to anneal the deposited metal films under vacuum at high temperatures. The film were deposited on 200 mm wafers with planar, dc magnetron sputtering sources without anysubstrate bias. The basic process steps studied for the multistep metallization include an initial layer deposition at low temperatures less than $100^{\circ}C$, and an annealin gstep at elevated temperatures, between 450 and $550^{\circ}C$. The degree of planarization or step coverage was dependent strongly upon the temperature and time of the flow step and complete filling of the submicron contacts with aluminum alloys was achieved. Responsible mechanisms for the enhancement in step coverge and factros determining uniform and reproducible flow of aluminum alloys during the high temperauture step are discussed.discussed.

• Transactions on Electrical and Electronic Materials
• /
• v.5 no.3
• /
• pp.122-125
• /
• 2004

ITO films were deposited on polyethylene terephthalate substrate by a dc reactive magnetron sputtering using rf bias without substrate heater and post-deposition thermal treatment. The dependency of rf substrate bias on plasma sputter processing was investigated to control energetic particles and improve ITO film properties. The substrate was applied negative rf bias voltage from 0 to -80 V. The composition of indium, tin, and oxygen atoms is strongly depended on the rf substrate bias. Oxygen deficiency is the highest at rf bias of -20 V. The electrical and optical properties of ITO films also are dominated obviously by negative rf bias.

• The Korean Journal of Ceramics
• /
• v.4 no.1
• /
• pp.9-14
• /
• 1998

Diamond-like carbon(DLC) films were deposited on buffer-layered ZnS substrates by radio frequency plasma enhanced chemical vapor deposition(RF-PECVD) method. Ge and GeC buffer layera were used between DLC and ZnS substrates to promote the adhesion of DLC on ZnS substrates. Ge buffer layers were sputter deposited by RF magnetron sputtering and $GeC^1$ buffer layers were deposited by same method except using acetylene reactive gas. The relatinship between film properties and deposition conditions was investigated using gas pressure, RF power and dc bias voltage as PECVD parameters. The hardness of DLC films were measured by micro Vickers hardness test and the adhesion of DLC films on buffer-layered ZnS substrates were studied by Sebastian V stud pull tester. The optical properties of DLC films on butter-layered ZnS substrates were characterized by ellipsometer and FTIR spectroscopy.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.12
• /
• pp.115-121
• /
• 1995

A mask for x-ray lithography is fabricated with SiN membrane and WTi absorber. SiN membrane is deposited by plasma enhanced chemical vapor deposition, and the stress of SiN membrane is controlled to be less than 100 MPa by rapid thermal annealing. WTi absorber is reactively deposited by DC-magnetron type sputter, and the working gases are argon and nitrogen. Added nitrogen is contributed to the stress of WTi absorber. The stress of WTi absorber is controlled to be less than $\pm$ 100 MPa by controlling the deposition pressure. 10$\mu$m WTi pattern is delineated on SiN membrane by dry etching technique.

• Journal of Surface Science and Engineering
• /
• v.32 no.6
• /
• pp.671-676
• /
• 1999

ITO (indium tin oxide) thin films on PET (polyethylene terephthalate) substrate have been deposited by a dc reactive magnetron sputtering without heat treatments such as substrate heater and post heat treatment. Each sputtering parameter during the sputtering deposition is an important factor for the high quality of ITO thin films deposited on polymeric substrate. Particularly, the material, electrical and optical properties of as-deposited ITO oxide films are dominated by the ratio of oxygen partial pressure. As the experimental results, the excellent ITO films are prepared on PET substrate at the operating conditions as follows : operating pressure of 5 mTorr, target-substrate distance of 45mm, do power of 20~30W, and oxygen gas ratio of 10%. The optical transmittance is above 80% at 550 nm, and the sheet resistance and resistivity of films are 24 Ω/square and $1.5\times$10$^{-3}$ Ωcm, respectively.

• Journal of Magnetics
• /
• v.2 no.4
• /
• pp.138-142
• /
• 1997

The magnetic and magneto-optical properties of Ni/Pt multilayers exhibiting square Kerr hysterisis loops at room temperature were studied. Squared polar Kerr hysterisis loops at room temperature in Ni/Pt multilayer thin films were obtained for the samples prepared by sequential dc magnetron sputter deposition of nickel and platinum with tNi=13-21$\AA$ and tPt=3.5-7.5$\AA$. The coercivity of these multilayers was in the range of 400-1100 Oe. The saturation magnetization was found to show an inverse dependence on nickel sublyaer thickness. About a monolayer of Ni at interface was observed to behave less magnetically than the interior Ni atoms. The polar Kerr rotation exhibited an increasing trend with decreasing wavelength in the spectral range of 7000-4000 $\AA$. The maximum of polar Kerr rotation was found to shift to higher wavelengths with increase in nickel sublayer thickness.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.760-763
• /
• 2007

The properties of carbon nanotube obtained by thermal chemical vapor deposition (CVD) process were investigated as a function of ammonia $(NH_3)$ gas in hydrocarbon gas, Fe catalyst thickness, and growth temperature. Fe catalyst was prepared by DC magnetron sputter and pre-treated with ammonia gas. CNTs were then grown with ammonia-acetylene gas mixture by thermal CVD. The diameter of these CNTs shows a strong correlation with the gas rate, the catalyst film thickness and temperature. From our results, it was found that the factors of grown CNTs positively acted to improve CNT quality.