• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.311-311
• /
• 2010

본 논문은 직류전원에 펄스주파수를 인가함으로써 AZO 박막이 미치는 영향에 대해 알아보기 위해 기존과는 다른 형태인 원통형의 회전(Cylindrical rotatable)하는 방식을 가진 DC magnetron sputter를 이용하였다. 인가되는 전력과 압력, 온도 그리고 거리는 각각 고정하였고 펄스 주파수 가변을 통해 박막의 전기적, 광학적, 구조적 그리고 SEM등의 다양한 특성에 대해 확인하였다. 박막의 광학적 특성인 투과도를 알아보기 위해 UV-Vis를 이용하여 측정하였고 가변 범위에 관계없이 550 nm의 파장 길이에서 약 90%의 투과도를 보였다. 그리고 펄스주파수가 증가할수록 XRD의 Intensity는 오히려 감소되는 경향을 보였고, 홀 측정을 통해 비저항의 증가와 전자농도 증가, 감소된 홀 이동도를 통해 증가된 펄스 주파수가 박막의 구조적, 전기적 특성이 얼마나 많은 영향을 끼치는지 또한 알 수 있었다. 그리고 펄스주파수는 면저항과 홀 이동도의 감소 요인이며 이것은 XRD의 결과로 확인하였다. 펄스주파수가 향후 박막 태양전지 및 TFT와 NVM 등의 소자를 적용하는데 있어 중요한 요소 중의 하나로 판단할 수 있다.

• Journal of Magnetics
• /
• v.9 no.3
• /
• pp.79-82
• /
• 2004

The structure and magnetic properties of Fe-Ni-N/Cu multilayered films, prepared by the DC magnetron sputter, as a function of different thicknesses of Fe-Ni-N ($t_{FeNiN}$) and Cu ($t_Cu$) layers have been studied by the methods of x-ray diffraction and measurement of magnetic moment. It has been found that the enhancement of (200) orientation in Fe-Ni-N layers is observed at the ratio of layer thickness with about $t_{FeNiN}/t_{Cu}$ $\underline{\simeq}$ 3.75. The reduction of magnetization due to the formation of interdiffusion near the interface is explained by means of the dead layer model. The temperature dependence of magnetization exhibits the feature of Blochs $T^{\frac{2}{3}}$ law. The layer thickness dependence of Curie temperature has been discussed by critical temperature theory of Heisenberg model.

• Journal of the Korean Ceramic Society
• /
• v.41 no.6
• /
• pp.476-480
• /
• 2004

AZO (Al-doped ZnO) thin films were deposited on glass by pulsed magnetron sputtering method, and their structural, electrical and optical properties were investigated. XRD patterns showed that a highly c-axis preferred AZO film was grown in perpendicular to the substrate when pulse frequency of 30 ㎑ was applied to the target. Microstructure of thin films showed that the fibrous grain of tight dome shape was grown. The deposition rate decreased linearly with increase of pulse frequency, and the lowest resistivity was 8.67${\times}$10$\^$-4/ $\Omega$-cm for the film prepared at pulse frequency of 30 ㎑. The optical transmittance spectra of the films showed a very high transmittance of 85∼90%, within visible wavelength region and exhibited the absorption edge of about 350 nm. The characteristics of the low electrical resistivity and high optical transmittance of AXO films suggested a possibility for the application to transparent conducting oxides.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.389-389
• /
• 2012

Molybdenum is one of the most important materials used as a back ohmic contact for $Cu(In,Ga)(Se,S)_2$ (CIGS) solar cells because it has good electrical properties as an inert and mechanically durable substrate during the absorber film growth. Sputter deposition is the common deposition process for Mo thin films. Molybdenum thin films were deposited on soda lime glass (SLG) substrates using direct-current planar magnetron sputtering technique. The outdiffusion of Na from the SLG through the Mo film to the CIGS based solar cell, also plays an important role in enhancing the device electrical properties and its performance. The structure, surface morphology and electrical characteristics of Mo thin films are generally dependent on deposition parameters such as DC power, pressure, distance between target and substrate, and deposition temperature. The aim of the present study is to show the resistivity of Mo layers, their crystallinity and morphologies, which are influenced by the substrate temperature. The thickness of Mo films is measured by Tencor-P1 profiler. The crystal structures are analyzed using X-ray diffraction (XRD: X'Pert MPD PRO / Philips). The resistivity of Mo thin films was measured by Hall effect measurement system (HMS-3000/0.55T). The surface morphology and grain shape of the films were examined by field emission scanning electron microscopy (FESEM: Hitachi S-4300). The chemical composition of the films was obtained by the energy dispersive X-ray spectroscopy (EDX). Finally the optimum substrate temperature as well as deposition conditions for Mo thin films will be developed.

• Journal of the Korean Physical Society
• /
• v.81
• /
• pp.867-875
• /
• 2022

This paper explored the effect of deposition conditions on the characteristics of copper oxide (CuO_x) thin films prepared by direct current (DC) magnetron sputtering. X-ray diffraction exhibited that CuO with n-type conductivity was the main composition regardless of the DC magnetron sputtering power whereas the phase transition from n-type CuO to p-type Cu₂O was observed with decreasing the oxygen pressure (OP) from 40 to 20%. The optical band gap ranges of 1.6-1.9 eV, which are characteristic of n-type CuO, were determined for samples prepared with OPs of 30-40% while the optical band gap of 2.3 eV, which is characteristic of p-type Cu₂O, was measured for samples prepared with an OP of 20%. In addition, only Cu⁺ X-ray photoelectron spectroscopy (XPS) peak at the ~932.6 eV position exists in the films deposited with an OP of 20%, whereas only Cu²⁺ XPS peaks at ~934.2 eV and in the range of 940-945 eV are observed in the films deposited with an OP of 40%. Furthermore, as a result of XPS depth profile analysis, it was confirmed that the composition ratio of the sample prepared at an OP of 20% was Cu₂O, whereas the composition ratio of the sample prepared at an OP of 40% was CuO. These suggest that the CuO_x thin films could be constantly converted from n-type CuO to p-type Cu₂O by decreasing the oxygen partial pressure. Thin film transistors with Cu₂O deposited at 20% OP revealed p-type characteristics such as onset voltage (V_ON) of -3 V, saturated hole mobility of 8 cm²/Vs at V_GS = -28 V, subthreshold swing of 0.86 V/decade at V_GS-V_ON = -0.5 V, and on/off ratio of 1.14 × 10³.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.725-728
• /
• 2001

We have fabricated thin films using the DC/RF magnetron sputtering of 74wt%Ni-l8wt%Cr-4wt%Al-4wt%Cu alloy target and studied the effect of the process parameters on the electrical properties for low TCR(Temperature Coefficient of Resistance) films. In sputtering process, pressure, power and substrate temperature, are varied as controllable parameter. The films are annealed to 400$^{\circ}C$ in air and nitrogen atmosphere. The sheet resistance, TCR of the films increases with increasing annealing temperature. It abruptly increased as annealing temperature increased over 300$^{\circ}C$ in air atmosphere. From XRD, it is found that these results are due to the existence of NiO on film surface formed by annealing. As a results of them, TCR can be controlled by variation of sputter process parameter and annealing of thin film.

• Journal of Surface Science and Engineering
• /
• v.40 no.5
• /
• pp.209-213
• /
• 2007

Change of the plasma volume by pulse frequency in a bipolar pulsed DC unbalanced magnetron sputtering was investigated. As increasing the frequency at off duty 10% and at a constant power, the plasma volume was lengthened in vertical direction from the AZO target. When there is an electrically floated substrate, the vertical length of the plasma area was not affected by the pulse frequency. Instead, the diameter of the plasma volume was increased. We found that the temperature rise of a substrate was affected by the pulse frequency, too. As increasing it, the maximum temperature rise of a glass substrate was decreased from $132^{\circ}C\;to\;108^{\circ}C$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.6
• /
• pp.1465-1468
• /
• 2010

The wet etching is a process using chemical solution and occurring chemical reaction on substrate surface. when we do wet etching process, we have to consider stoichiometry, etching time and temperature of etchant for good resolution. In this experiment, we used Cr, Al andIndium-tin-oxide (ITO) metal and we deposited them with DC sputtering machine. The Cr thin film metal thickness is about $1300{\AA}$, ITO films show a low electrical resistance and high transmittance in the visible range of an optical spectrum and Ai film is used for signal line. We measured and analysed wet etching properties on the metal thin films.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.795-797
• /
• 2010

습식 식각은 식각용액으로서 화학용액을 사용하는 공정으로 반응물이 기판표면에서 화학반응을 일으켜 표면을 식각하는 과정이며, 표면결합의 제거를 위한 식각연마와 폴리싱을 위한 식각, 그리고 구조적 형상 패턴등이 있다. 여기서 화학용액은 산화제 또는 환원제 역할을 하는 혼합용액으로 구성된다. 습식 식각 시 수${\mu}m$의 해상도를 얻기 위해서는 그 부식액의 조성이나, 에칭시간, 부식액의 온도 등을 고려하여야 한다. 또한 습식 식각 후 포토 레지스트를 제거하는 과정에서 포토 레지스트를 깨끗이 제거해야 하며, 제거공정 자체가 a-Si:H 박막을 부식 하지 않을 조건으로 행하여야 한다. 포토레지스트 제거 후 잔류 포토 레지스트를 제거하기 위해서 본 실험에서는 RCA-I 세척 기법을 사용한 후 D.I 로 린스 하였다. 본 실험에서 사용한 금속은 Cr, Al, ITO 로 모두 DC sputter 방법을 사용해서 증착하여 사용하였다. Cr박막은 $1300\AA$ 정도의 두께를 사용하였고, ITO (Indium Tin Oxide) 박막은 가시광 영역에서 투명하고 (80% 이상의 transmittance), 저저항 (Sheet Resistance : $50{\Omega}/sq$ 이하) 인 박막을 사용하였으며, 신호선으로 주로 사용되는 Al등의 증착조건에 따른 wet etching 특성을 조사하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.137.2-137.2
• /
• 2010

본 연구는 스테인리스 스틸(STS)을 직접메탄올 연료전지(DMFC)용 바이폴라 플레이트에 적용하기 위한 것이다. 약산성의 연료전지 환경에서 부식저항성을 향상시키고자 오스테나이트계 STS 316L과 페라이트계 STS 430에 UBM(unbalanced magnetron) DC sputter로 CrN 코팅막을 제작하였다. CrN이 코팅된 스테인리스 스틸은 부식특성, 접촉 저항 및 접촉각 등을 측정하여 무 코팅의 스테인리스 스틸과 특성을 비교하였다. 그리고 이들 재료의 연료전지(DMFC) 적용 가능성을 알아보기 위하여 단위전지로 제작하여 연료전지 성능 등을 측정하고 평가하였다. 무 코팅 스테인리스 스틸(STS 316L, STS 430)과 CrN 코팅 스테인리스 스틸의 부식저항 특성은 동전위와 정전위 실험으로 조사하였다. 동전위 부식 실험은 -0.4~1.0 V로 0.001 M의 황산용액 또는 메탄올을 첨가하여 질소 또는 공기의 환경에서 실험을 실시하였으며, 정전위 부식 실험은 0.4 V 또는 0.6 V에서 진행하였다. 연료전지의 단전지 측정은 실제 DMFC의 운전조건에서 실시하였다. 부식실험과 단전지 실험 전/후 메탈 바이폴라 플레이트의 조직 변화는 SEM을 통해 관찰하였고, 부식산화물의 화학적 조성과 메탈 바이폴라의 표면은 EDS를 이용하여 측정하였다.