• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.2051-2054
• /
• 2004

This paper proposes a more accurate task level energy measurement technique for high speed microprocessors. The technique is based on the relationship of the amount of current consumed by the microprocessor and the pulse width of the power supply controller chip, employed in the synchronous buck DC-DC converter in the microprocessor's power supply. The accuracy of the measurement is accomplished by measuring variation in pulse width in each power supply cycle. The major advantage of this technique is that its accuracy does not depend on the operating frequency of the microprocessor. To prove the proposed technique, we implemented the measurement unit of the microprocessor energy meter using an FPGA chip operating at 50 MHz. Both static and dynamic load measurement are tested in order to obtain some behaviours. Moreover, various commercially available mainboards which employ synchronous buck regulators at 200 KHz switching frequency, were measured. The results agree with previous works with better accuracy at higher operating frequency.

• 전기학회논문지P
• /
• 제59권4호
• /
• pp.372-376
• /
• 2010

Electrolytic capacitors have been widely used in power electronics system because of the features of large capacitance, small size, high-voltage, and low-cost. Electrolytic capacitors, which is most of the time affected by aging effect, plays a very important role for the power electronics system quality and reliability. Therefore it is important to estimate the parameter of an electrolytic capacitor to predict the failure. The estimation of the equivalent series resistance(ESR) is important parameter in life condition monitoring of electrolytic capacitor. This paper proposes a simple technique to measure the ESR of an electrolytic capacitor. This method uses a switching DC/DC boost converter to measure the DC Bus capacitor ESR of power converter. Main advantage of the proposed method is very simple in technique, consumes very little time and requires only simple instruments. Simulation results are shown to verify the performance of the proposed method.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.687-688
• /
• 2008

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2000년도 학술대회논문집
• /
• pp.99-104
• /
• 2000

This paper present the design, produce, circuit design and practical measurement for a Brushless DC Motor(BLDCM) with Ferrit-Magnet. It was used PI controller. The practical PI control has bin widely used for DC-Motor.

• 전기학회논문지
• /
• 제57권5호
• /
• pp.866-874
• /
• 2008

Motor frequency can be measured by a hall sensor. Among the many hall sensors, a linear type hall sensor is good at high accuracy frequency measuring problem. However, in general, this linear type hall sensor has DC offset which can vary along sensor's operating voltage change. Therefore, In motor frequency measurement problem using the linear hall sensor, it needs an estimator that can estimate frequency and DC offset simultaneously. In this paper, we propose the least mean square estimator to estimate motor frequency. To verify its performance, we compare the LMS estimator with a commercial analog tachometer. Experimental results shows the proposed LMS estimator works well in varying frequency and stationary DC offset.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 일렉트렛트 및 응용기술
• /
• pp.148-151
• /
• 2002

In order to prevent the failures of underground distribution power cables we need to measure insulation condition in the field. Until now we used DC high voltage as a power source for the cable diagnosis but it was not proper method to the XLPE insulation cables because DC high voltage can affect sound insulation and can't diagnose exactly insulation degradation. For these reasons we imported isothermal relaxation current measurement system called by KDA-1 from germany but it's reliability did not proved in our URD cables. DC voltage decay measurement system was developed by domestic company but they don't have field experience. In this paper we tried to prove reliability of these two systems in the field. Through the field diagnosis and Ac breakdown test the two systems showed similar results.

• 전자공학회논문지 IE
• /
• 제45권4호
• /
• pp.7-10
• /
• 2008

본 연구에서는 load-pull 장비를 이용하여 hot carrier 현상에 따른 RF 전력 성능 저하를 측정 분석하였다. 스트레스를 인가한 주에 RF 전력 지수들은 감소하였으며, 고정 전압 조건에서 관찰한 SOIl MOSFET의 DC 성능 지수들 또한 hot carrier stress로 인하여 감소함을 할 수 있었다. 또한 Hot carrier stress로 인한 DC 성능 저하로 인하여 RF 전력 성능 저하의 감소를 알 수 있었다.

• Journal of Power Electronics
• /
• 제10권6호
• /
• pp.635-642
• /
• 2010

The paper presents a multimedia educational program of DC servo drives for distant learning with a special emphasis on sliding mode control. The program contains of three parts: animation, simulation and internet based measurement. The animation program explains the operation of DC motors, gives its time- and frequency-domain equations, transfer functions and the theoretical background necessary for controller design for DC servo motors. The simulation model of the DC servo motor and the controller can be designed by the students based on the animation program. The students can also test their controllers through the internet based measurement, which is the most important part from engineering point of view. After the measurements are executed, the students can download the measured data and compare them to the simulation results.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.599-600
• /
• 2005

The measurement method of electrical conductivity of the metal use a generally DC technique. Traceability to national standards in many countries is achieved using DC measurement technique and recently it's interested in AC technique. As a results for AC technique, the properties of electrical conductivity of non-ferrous and ferrous metals is decreasing at low frequency level.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2014년도 추계학술대회 논문집
• /
• pp.66-67
• /
• 2014

Stabilization of the DC bus voltage is an important task in DC-AC microgrid system with renewable energy source such as solar system. A battery energy storage system (BESS) has become a general solution to stabilize the DC-bus voltage in DC-AC microgrid. This paper develops the analog BESS controller which requires neither computation nor dc-bus voltage measurement, so that the system can be implemented simply and easily. Even though others methods can stabilize and control the DC-bus voltage, it has complicated structure in control and low adaptive capability. The proposed topology is simple but is able to compensate the solar source variation and stabilize the DC-bus voltage under any loads and distributed generation (DG) conditions. In addition, the design of analog controller is presented to obtain a robust system. In order to verify the effectiveness of the proposed control strategy, simulation is carried out by using PSIM software.