• Journal of the Korea Convergence Society
• /
• v.9 no.4
• /
• pp.143-150
• /
• 2018

This work conducted the experimental analysis on ultrasonic acoustic matching in order to measure the accuracy of gaseous fuel level values. The experimental devices were used as 12V-DC supply, control T1 board, oscilloscope (DS01072B), ultrasonic probe and pattern table. The research models were designed by ceramic assay which can determine the transmitting and receiving energies. The result of the ringing area could verify the increased characteristics in the order of D (0.180m) < E (0.184m) < B (0.204m) < A (0.234m) < F (0.244m) < C (0.247m) models based on initial 2.9V of the maximum peak voltage. From the experimental results, the model designed by Ø21*3+2t of the matching layer was notable in that the most outstanding directivity energy could be created.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.3
• /
• pp.9-16
• /
• 1997

A 23GHz 1-stage LNA was designed by using new topology of coupled line type with EEsof softwares and modified by using MPIE numerical analysis. The parallel coupled filter-type matching sections give impedance matching and DC blocking simultaneously, and have small discontinuities. This matching scheme has simple structure in the design process and give small error. The EFT chip was directly attached to the ground metal. The designed LAN gives 6.2dB gain and 2.5dB noise figure without considering the loss of connectors. Through these results, it was verified that our design process, matching schemes and fabrication technologies was valied for developing 20GHz-band LNA.

• Journal of Satellite, Information and Communications
• /
• v.12 no.2
• /
• pp.89-93
• /
• 2017

This paper introduces an energy harvesting system that generates energy by collecting multi-band RF signals using buck-boost DC-DC converter. In an environment where the resistance of load using the collected electric energy is constantly changing, a buck-boost DC-DC converter is used in which the input resistance of the DC-DC converter does not change even if the load resistance changes. Since the frequency band of the input RF signal varies, the rectifier is designed for each band so that multiple bands can be processed, and a matching circuit is added to each band in front of the rectifier. For a rectifier to collect very small RF signals, a circuit is designed so that a constant voltage is obtained according to a very small input signal by devising a method of continuously accumulating the voltages collected and generated in each band. It is confirmed that the output efficiency can reach up to 20% even for the RF signal having the input of -20 dBm.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.6
• /
• pp.43-48
• /
• 2006

In this paper, the rectenna converting 2.45[GHz] microwave into DC power is designed and fabricated for wireless power transmission using microwave and the methode for impedance matching and tuning are proposed in order to maximize RF-DC conversion efficiency. The fabricated rectenna can be easily tuned by using a broad open stub and has the RF-DC conversion efficiency up to 59[%] when the 5[dBm] input power is applied. The 2.2[V], 1.5[mW] DC level, in the 1[m] distance between the transmitter and the receiver can be obtained and this value is avaliable in the small power digital system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.3C
• /
• pp.59-63
• /
• 2005

We propose non-DC-free generalized PRML (GPRML) that are suppressed DC contents for matching to the response of perpendicular magnetic recording channel with a ring-head. In addition, DC-free encoding is considered to prevent low-frequency disturbances. The SNR performance is obtained by combining the various PRML channels with DC-free and non-DC-free codes during the normalized recording density increases from 2.5 to 3.5. The GPRML detections without using DC-free code get SNR gains more than 1dB compared to the conventional PRML systems at 10/sup -5/BER. We confirmed that the rate 127/136 DC-free coded GPRML systems show good performances compared with the 16/17 non-DC-free coded GPRML systems. In results, DC-free coded GPRML detections get gains about 1.4dB and 2.0dB at the density of 3.3 and 3.5, respectively.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.3
• /
• pp.34-42
• /
• 1993

An analytic approach to wide-band amplification using simplified equivalent MESFET modeling has enabled an ultrabroad-band flat-gain amplifier from DC to microwave. The developed lossy-match ultrabroad-band amplifier operates as a RC coupled circuit in the low-frequency range and lossless impedance matching circuit in the microwave frequency range with gain compensation circuits. The reduced gain caused by external resistors is compensated using 2-stage cascade amplification, and the gain of designed unit is 12.5.+-.1dB from the vicinity of DC to 7GAz. The experimental gain characteristics are good agreement with computer simulated results. The input and output VSWRs are measured under 2:1 over the operating frequency range, and the gain goes down over 15dBrange with various gate bias voltages.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.1 s.92
• /
• pp.102-112
• /
• 2005

In this work, we developed fully integrated broadband MMIC chip set employing CSP(Chip Size Package) for K/Ka band applications. By utilizing an ACF for the RF-CSP, the fabrication process for the packaged amplifier MMIC could be simplified and made cost effective. $STO(SrTi_{3})$ capacitors were employed to integrate the DC biasing components on the MMIC, and LC parallel circuits were employed for DC feed and ESD protection. A pre-matching technique and RC parallel circuit were used to achieve a broadband matching and good stability fer the amplifier MMIC in K/Ka band. The amplifier CSP MMIC exhibited good RF performance over a wide frequency range in K/Ka band. This work is the first report of a fully integrated CSP amplifier MMIC successfully operating in the K/Ka band.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.4A
• /
• pp.458-465
• /
• 2004

To reaffirm the use of a mainstream CMOS process for designing passive-like attenuator structures, a linearly controlled variable attenuator is realized with 0.35${\mu}{\textrm}{m}$ 2-poly 4-metal CMOS process. It uses the П configuration for large attenuation range and suitable matching property. Compared to conventional passive-like CMOS attenuators, it is demonstrated that this work advances the frequency band from MHz to ㎓ (DC- l㎓), and reduces the size to 700${\mu}{\textrm}{m}$${\times}$300${\mu}{\textrm}{m}$.. Both simulation results and test results are provided. They show the improved linear relation between attenuation and control voltage. It is very useful in CDMA or GSM band, which uses under 1㎓ frequency band. An alternative topology, Bridged-T configuration, is proposed to get over the limit of applications by elevating operation bandwidth. The proposed topology covers over DC-2㎓ frequency band, which means that the proposed architecture can cover the tripleband (800MHz CDMA/GSM, 1.5㎓ GPS, 1.9㎓z PCS system) in applications as well. The simulation results are provided.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.279-284
• /
• 2005

We investigated the impedance matching characteristics of UHF-band RFID tag antenna and tag chip for increased reading range. A voltage multiplier designed using 0.4 $\mu$m zero-$V_T$ MOSFET showed that DC output voltage of about 2 V can be obtained using standard CMOS process. The input impedance of the voltage multiplier was examined to achieve impedance matching to the RFID tag antenna using analytical and numerical approaches. The input impedance of the voltage multiplier could be varied in a wide range by selecting the size of MOSFET and the number of multiplying stages, and thus can be impedance matched to a tag antenna in presence of other tag circuit blocks. A meander line inductively-coupled RFID tag antenna operating at UHF band also shows the feasibility of impedance matching to tile RFID tag chip.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.2
• /
• pp.569-575
• /
• 2014

A highly efficient class E power amplifier is demonstrated for application to wireless power transfer system. The amplifier is designed with an L-type matching at the output for harmonic rejection and output matching. The power loss and the effect of each component in the amplifier with the matching circuit are analyzed with the current ratio transmitted to the output load. Inductors with a quality factor of more than 120 are used in a dc feed and the matching circuit to improve transmission efficiency. The single-ended amplifier with 20 V supply voltage shows 7.7 W output power and 90.8% power added efficiency at 6.78 MHz. The wireless power transfer (WPT) system with the amplifier shows 5.4 W transmitted power and 82.3% overall efficiency. The analysis and measurements show that high-Q inductors are required for the amplifier design to realize highly efficient WPT system.