• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 추계학술대회 논문집 학회본부
• /
• pp.228-230
• /
• 1994

A Spotter ion Plating(SIP) system with a r. f. coil electrode and the Facing Target Sputter(FTS) source was designed for high-quality thin film formation. The rf discharge was combined with DC facing target sputtering in order to enhance ionization degree of a sputtered atoms. The discharge voltage-discharge characteristics curves of a FTS source could be characterized by the fern of $I{\propto}V^n$ with n in the range of $8{\sim}12$. The energy of ions incident on the substrate depended on the sheath potential of DC biased substrate. The mean impact ion energy increased with negative bias voltage and rf power. The adhesive force of the TiN film formed was in the range of $30{\sim}50N$, and markedly influenced by substrate bias voltage.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.309-312
• /
• 2002

Ferroelectric $Sr_{0.3}Ba_{0.7}Nb_{2}O_{6}$ (SBN30) thin films were deposited on Pt/Ti/$SiO_{2}$/Si(100) substrates by ion beam sputtering. During annealing treatment at $750^{\circ}C$, poling was attempted by applying dc voltage bias across polished surfaces. Phase relation, microstructure and crystallization behavior were examined using XRD and FE-SEM. Ferroelectric hysteresis characteristics were also determined where both remanent polarization and coercive values decreased with the increase of bias voltage. The measured remanent polarization and coercive field values at 5 V and 10 V bias were $36{\mu}C/cm^2$, $10{\mu}C/cm^2$ and 100kV /cm, 80kV /cm, respectively.

• Journal of Electrical Engineering and Technology
• /
• 제6권4호
• /
• pp.505-512
• /
• 2011

A novel passive boost power converter forsingle-phaseswitched reluctance motor is presented. A simple passive circuit is proposed comprisingthree diodes and one capacitor. The passive circuitis added in the front-end of a conventional asymmetric converter to obtain high negative bias. Based on this passive network, the terminal voltage of the converter side is a general DC-link voltage level in parallel mode up to a double DC-link voltage level in series mode. Thus,it can suppress the negative torque generation from the tail current and improve the output power. The results of the comparative simulation and experiments forthe conventional and proposed converter verify the performance of the proposed converter.

• Corrosion Science and Technology
• /
• 제9권6호
• /
• pp.276-280
• /
• 2010

Copper(Cu) as an interconnecting metal layer can replace aluminum (Al) in IC fabrication since Cu has low electrical resistivity, showing high immunity to electromigration compared to Al. However, it is very difficult for copper to be patterned by the dry etching processes. The chemical mechanical polishing (CMP) process has been introduced and widely used as the mainstream patterning technique for Cu in the fabrication of deep submicron integrated circuits in light of its capability to reduce surface roughness. But this process leaves a large amount of residues on the wafer surface, which must be removed by the post-CMP cleaning processes. Copper corrosion is one of the critical issues for the copper metallization process. Thus, in order to understand the copper corrosion problems in post-CMP cleaning solutions and study the effects of DC biases and post-CMP cleaning solution concentrations on the Cu film, a constant voltage was supplied at various concentrations, and then the output currents were measured and recorded with time. Most of the cases, the current was steadily decreased (i.e. resistance was increased by the oxidation). In the lowest concentration case only, the current was steadily increased with the scarce fluctuations. The higher the constant supplied DC voltage values, the higher the initial output current and the saturated current values. However the time to be taken for it to be saturated was almost the same for all the DC supplied voltage values. It was indicated that the oxide formation was not dependent on the supplied voltage values and 1 V was more than enough to form the oxide. With applied voltages lower than 3 V combined with any concentration, the perforation through the oxide film rarely took place due to the insufficient driving force (voltage) and the copper oxidation ceased. However, with the voltage higher than 3 V, the copper ions were started to diffuse out through the oxide film and thus made pores to be formed on the oxide surface, causing the current to increase and a part of the exposed copper film inside the pores gets back to be oxidized and the rest of it was remained without any further oxidation, causing the current back to decrease a little bit. With increasing the applied DC bias value, the shorter time to be taken for copper ions to be diffused out through the copper oxide film. From the discussions above, it could be concluded that the oxide film was formed and grown by the copper ion diffusion first and then the reaction with any oxidant in the post-CMP cleaning solution.

• 한국초전도ㆍ저온공학회논문지
• /
• 제6권2호
• /
• pp.29-34
• /
• 2004

The linear type flux pump aims to compensate a little bit decremental persistent current of the HTS magnet in NMR and MRI spectrometers. The flux pump mainly consists of DC bias coil, 3-phase AC coil and Nb foil. The persistent current in closed superconductive circuit can be easily adjusted by the 3-phase AC current, its frequency and the DC bias current. In the experiment, it has been investigated that the flux pump can effectively charge the current in the load coil of 543 mH for various frequencies in 18 minutes under the DC bias of 10 A and the AC of 5 $A_{rms}$. The maximum magnitudes of pumping current and load magnet voltage are 0.72 A/min and 20 ㎷, respectively. Based on simulation results by the FEM are proved to nearly agree with experimental ones.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.408-411
• /
• 2003

Al doped Zinc Oxide(ZnO:Al) films, which is widely used as a transparent conductor in optoelectronic devices such as solar cell, liquid crystal display, plasma display panel, thermal heater, and other sensors, were prepared by using the capacitively coupled DC magnetron sputtering method. The influence of the substrate temperature, working gas pressure, discharge power and doping amounts of Al on the electrical, optical and morphological properties were investigated experimentally. The effect of bias voltage on the electrical properties of ZnO thin film were also studied. Films with lowest resistivity of $5.4{\times}10^{-4}\;{\Omega}-cm$ have been achieved in case of films deposited at 1mtorr, $400^{\circ}C$ with a substrate bias of +10V for 840nm in film thickness.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 춘계학술대회 논문집
• /
• pp.55-58
• /
• 1996

A new type CuN/Cu/CuN thin film electrode material with high adhesion to glass was developed by the dc reactive planar magnetron sputtering system for the PDP(Plasma Display Panel). The adhesive force of the CuxN thin film was in the range of 20∼40(N) under the conditions of the N$_2$ partial pressure of 15%, discharge current of 70mA, discharge voltage of 450v and substrate bias voltage of -100V. The adhesive force was depended on the N$_2$ partial Pressure, discharge current and substrate bias voltage.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권9호
• /
• pp.527-532
• /
• 2000

The performance of ac plasma display panels (PDP) is influenced strongly by the surface glow discharge characteristics on the MgO thin films. This paper deals with the surface glow discharge characteristics and some physical properties of MgO thin films prepared by reactive RF planar unbalanced magnetron sputtering in connection with ac PDP. The samples prepared with dc bias voltage of -10V showed lower discharge voltage and lower erosion rate byion bombardment than those samples prepared by conventional magnetron sputtering or E-beam evaporation. The main factor that improves the discharge characteristics by bias voltage is considered to be due to the morphology changes or crystal structure of the MgO thin film by ion bombardement during deposition process.

• Journal of Electrical Engineering and Technology
• /
• 제12권6호
• /
• pp.2227-2236
• /
• 2017

In order to solve the neutral-point voltage fluctuation problem of three-phase three-level T-type inverters (TPTLTIs), the unbalance characteristics of capacitor voltages under different switching states and the mechanism of neutral-point voltage fluctuation are revealed. Based on the mathematical model of a TPTLTI, a feed-forward voltage balancing control strategy of DC-link capacitor voltages error is proposed. The strategy generates a DC bias voltage using a capacitor voltage loop with a proportional integral (PI) controller. The proposed strategy can suppress the neutral-point voltage fluctuation effectively and improve the quality of output currents. The correctness of the theoretical analysis is verified through simulations. An experimental prototype of a TPTLTI based on Digital Signal Processor (DSP) is built. The feasibility and effectiveness of the proposed strategy is verified through experiment. The results from simulations and experiment match very well.

• Korean Chemical Engineering Research
• /
• 제43권4호
• /
• pp.531-536
• /
• 2005

포토리지스트 마스크로 패턴된 CoTb 및 CoZrNb 자성 박막에 대한 유도 결합 플라즈마 반응성 이온 식각이 $Cl_2/Ar$와 $C_2F_6/Ar$ 가스를 이용하여 진행되었고 식각 속도와 식각 프로파일 측면에서 조사되었다. $Cl_2$와 $C_2F_6$ 가스의 농도가 증가함에 따라서 자성 박막들의 식각 속도는 감소하였고 식각 경사는 낮아졌다. 자성 박막들의 식각 가스로서 $Cl_2/Ar$이 빠른 식각 속도와 가파른 식각 경사를 얻는데 있어서 $C_2F_6/Ar$ 보다 더 효과적이었다. Coil rf power의 증가는 플라즈마 내의 Ar 이온과 라디칼의 밀도를 증가시키고 dc bias voltage의 증가는 기판으로 스퍼터되는 Ar 이온의 에너지를 증가시키기 때문에 coil rf power와 dc bias voltage가 증가할수록 식각 속도와 식각 경사는 증가하였지만 패턴의 측면에서 재증착이 일어났다. 자성 박막들의 적층으로 형성된 magnetic tunnel junction stack에 고밀도 플라즈마 반응성 이온 식각을 적용하여, 높은 식각 경사와 재증착이 없는 깨끗한 식각 프로파일을 얻었다.