• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.83-84
• /
• 2011

This paper presents an analysis and a novel strategy for a doubly fed induction generator (DFIG) based wind energy conversion system under unbalanced grid voltage and non-linear load conditions. A proportional-resonant (PR) current controller is applied in both grid side converter (GSC) and rotor side converter (RSC). The RSC is controlled to mitigate the stator active power and the rotor current oscillations at double supply frequency under unbalanced grid voltage while the GSC is controlled to mitigate ripples in the dc-link voltage and compensate harmonic components of the network current. Simulation results using Psim simulation program are presented for a 2 MW DFIG to confirm the effectiveness of the proposed control strategy.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.10
• /
• pp.1858-1864
• /
• 2011

This paper suggests a control technique of the sensorless brushless DC (BLDC) motor drive for a vehicle fuel pump application. The sensorless technique based on a comparator and a potential start-up method with high starting torque are proposed. The comparator is used to generate the commutation signals in phase with the three-phase back-EMFs. The rotor position is aligned at standstill for maximum starting torque without an additional sensor and any information of motor parameters. Also, the stator current can be easily adjusted by modulating the pulse width of the switching devices during alignment. Some experiments are implemented on a single chip 16-bit DSP controller to demonstrate the feasibility of the sensorless techniques.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.3
• /
• pp.232-238
• /
• 2015

A sensorless control algorithm of brushless DC (BLDC) motors with a model current based on 120 degree conduction mode is proposed in this paper. The rotor speed and position can be estimated using the current model of BLDC motor, which is a modified version of the conventional current model of permanent magnet synchronous motor. The rotor speed and position can be obtained using the difference of the actual current and the model current. The position error caused by the parameter errors of the model current is compensated using a PI controller and the feedback loop of the real current. The validity of the proposed sensorless control algorithm is verified through simulation.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.1
• /
• pp.1-6
• /
• 2014

A new sensorless control strategy for brushless DC (BLDC) motors is proposed in this paper. This technique builds a rotor position-related flux function, which is independent of the speed. By observing the flux function, the information of rotor position and commutation can be obtained. As the function is not speed-related, this control process can be used in a wider range of speed and improves the motor's performance during startup. An experimental test bad based on TMS320F2812 has been built, and the experimental result indicates that the motor achieves a smooth starting-up and stable phase commutation with the proposed control strategy.

• Journal of Power Electronics
• /
• v.9 no.1
• /
• pp.1-17
• /
• 2009

Permanent magnet brushless DC (PMBLDC) motors are the latest choice of researchers due to their high efficiency, silent operation, compact size, high reliability and low maintenance requirements. These motors are preferred for numerous applications; however, most of them require sensorless control of these motors. The operation of PMBLDC motors requires rotor-position sensing for controlling the winding currents. The sensorless control would need estimation of rotor position from the voltage and current signals, which are easily sensed. This paper presents state of the art PMBLDC motor drives with an emphasis on sensorless control of these motors.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.11
• /
• pp.1894-1899
• /
• 2016

In this paper, because the position sensor represents the important factor in BLDC (Brushless DC) motor drives, BLDC motor is necessary that the three Hall-sensors evenly be distributed around the stator circumference in case of the 3 phase motor. The Hall-sensor is set up in this motor to detect the main flux from the rotor. So the output signal from Hall-sensor is used to drive IGBT to control the stator winding current. However, in case of breakdown Hall sensor, we research that the estimation algorithm of Hall sensor signal to detect rotor position and for the speed feedback signals with BLDC motor whose six stator and two rotor designed. In addition, this paper presents a sensorless speed control of BLDC Motor using terminal voltage of the one phase. Rotor position information is extracted by indirectly sensing the back EMF from only one of the three terminal voltages for a three-phase BLDC motor.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.4
• /
• pp.567-573
• /
• 2012

Outer rotor type in-wheel Blushless DC Motor(BLDCM) for three-wheeled electric vehicle is researched. In-wheel system is to drive the electric vehicle without mechanical transmission, shaft, differential gears or other mechanical system. The motor is designed considering the performance requirements and drive modes of the vehicle. The determined dimensions as well as the slot and rotor pole are simulated by magnetic and thermal finite element analysis and ansys workbench to analyze the performance and heating of the motor. In order to verify the performance characteristics of the proposed motor, the experiment tests are executed and satisfy well the requirements.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.1
• /
• pp.1-9
• /
• 2001

In this paper, the general research on the analysis of the vibration due to magnetic exciting force in the small brushless DC(BLDC) motor, which is used in the Digital Versatile Disk(DVD) ROM driving system, is performed. The first part of the study is the analysis of the magnetic exciting force in the air gap region. As a verification of the exciting force by numerical analysis, the magnetic exciting force distribution in the air gap region is computed by using Reluctance Network Method(RNM). In addition, the effect of the eccentricity on the magnetic exciting force is discussed. The other part of the research is the structural analysis of the rotor structure of the BLDC motor. The matural mode analysis of the rotor structure is performed, and the vibration response due to magnetic exciting force is found. As a result of the procedures, the basic estimation of the effect of the magnetic exciting force on the vibration of BLDC motor is suggested.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.3
• /
• pp.40-46
• /
• 2009

Toroidally-wound brushless direct-current (BLOC) machines are compact, highly efficient, and can work across a large magnetic gap. For these reasons, they have been used in pumps, flywheel energy storage systems and left ventricular assist devices among others. The common feature of these systems is a spinning rotor supported by a set of (either mechanical or magnetic) bearings. From the view point of dynamics, it is desirable to increase the first critical speed of the rotor so that it can run at a higher operating speed. The first critical speed of the rotor is determined by the radial stiffnesses of the bearings and the rotor mass. The motor also affects the first critical speed if the rotor is displaced from the rotating center. In this paper, we analytically derive the flux density distribution in a toroidally-wound BLOC machine and also derive the negative stiffness of the motor, based on the assumption that the rotor displacement perturbs the flux density distribution linearly. The estimated negative stiffness is validated by finite element analyses.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.11 no.9
• /
• pp.454-461
• /
• 2001

Acoustic noise and vibration of a BLDC motor is a coupled phenomenon between mechanical characteristics and electromagnetic origins through the motor air-gap. When a relative misalignment of rotor in the air-gap center exists on the assemblage, it is considered to influence the motor system characteristics. In this paper, the back electro motive force(BEMF) is analyzed by Finite Element Method(FEM) and verified by experiments for the SPM and IPM type motors. For magnetic field analysis, a FEM is used to account for the magnetic saturation. Using these results, the FEM is made to determine the appropriate electromagnetic field analysis in BLDC motors with rotor eccentricity ratio. A radial magnetic imbalance force of BLDC motor with rotor eccentricity is analyzed. Results demonstrate that the imbalance force is increased according to the degree of misalignment. An IPM motor, mostly chosen to realize high-speed operation, shows a worse effect on magnetic unbalanced forces and dynamic responses compared with SPM motor due to magnetic saturation when the rotor eccentricity exists.