• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.04a
• /
• pp.89-92
• /
• 1993

This paper deals with the effect of siliceous slurry coatings on mortar microstructure under a damp environment. For estimation on effect of siliceous slurry coating, microstructure of coated mortar was observed through SEM. Crystal production in mivrosturcture of coated mortar was periodically increased, and more produced in mortar of high water-cement ratios. And they were generated mainly in mortar ranging from the surface to the inside about 2.5 or 3mm deep.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.04a
• /
• pp.257-262
• /
• 1996

The first purpose of this study investigates the influence of stiffening on the acoustic response of stiffened plates, which are often employed in steel structures. And the radiation efficiency is measured by average mean square velocity and sound intensity of stiffened plates. The second, it determines influence of mass, damp and stiffeness due to the partial adhesive visco-elastic material to reduce radiated sound power.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.8 no.2
• /
• pp.39-49
• /
• 2004

Model of the novel Surface motor (SFM) is briefly discussed, and two types of control method including two-order feedback circuit control, indirect acceleration feedback control are analyzed to solve unstable characteristic such as low damp and negative stiffness. The simulation results demonstrate that the system has plain amplitude and wide frequency band arranging from 0 to 8kHz with no resonant peak through indirect acceleration feedback control.

• Proceedings of the Zoological Society Korea Conference
• /
• 2001.10a
• /
• pp.256.1-256
• /
• 2001

No Abstract, See Full Text

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.7-11
• /
• 1991

The adaptive control of flexible joint manipulator is the focus of this paper. The full order flexible joint manipulator dynamic system does not allow the determination of a feedback linearization control as for rigid manipulators. This drawback is overcome by a model order reduction based on a singular perturbation strategy. The full order flexible joint manipulator dynamic model is adopted for derivation of the adaptive control law to damp out the elastic oscillations at the joints. It is shown that the joint position error will converge to zero asymptotically and that other signals remain bounded without precise knowledge of parameters of the manipulator and its joint flexibility.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.38 no.5
• /
• pp.337-342
• /
• 1989

Since the late 1960s, the selection of the parameters of power system stabilizer (PSS) to damp out sustained low frequency oscillation of power generators in the steady state has been an active research area. This paper presents a new approach to select the optimal PSS parameters using the sensitivity of the quadratic performance with respect to the PSS parameters. The proposed algorithm has been applied to Seo-Cheon fossil power plant.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10b
• /
• pp.946-951
• /
• 1998

In order to calculate the thermal stresses of massive concrete structures in non-steady state conditions the thermal properties of the materials have to be well known. Structural materials such as concrete, rock and soil are heterogeneous, damp and porous so that measurements of their thermal properties by conventional methods would result in large errors. In this study, thermal conductivity was measured by the device, QTM-D3 which is usually used in Japan. Variables are chosen as age, water content, temperature, aggregate content, S/A ratio and type of cementitious materials. Finally a model for thermal conductivity was proposed.

• Advances in aircraft and spacecraft science
• /
• v.3 no.2
• /
• pp.211-224
• /
• 2016

The present study aims to investigate the shimmy stability behavior of a single wheeled nose landing gear system. The system is supposed to be equipped with an electromechanical actuator capable to control the shimmy vibrations. A Proportional-Integrative-Derivative (PID) controller, tuned by using the Particle Swarm Optimization (PSO) procedure, is here proposed to actively damp the shimmy vibration. Time-history results for some test cases are reported and commented. Stochastic analysis is last presented to assess the robustness of the control system.

• The Journal of Korean Medicine Ophthalmology and Otolaryngology and Dermatology
• /
• v.16 no.1
• /
• pp.226-235
• /
• 2003

The relapsed patient who has diagnosed flat wart and treated with continuous immunotherapy in Western Dermatology come to Dongshin University Oriental Medical hospital OPD Ophthalmology and Otolaryngology from 23 December 2002 to 18 March 2003. We diagnosed as Gi(氣) deficiency and stagnation of damp. stagnation of Gi(氣) and blood stasis caused by insufficiency of Yang of the spleen treated with Gamiijungtang(加味理中湯) and Sodogeumgagam(消毒飮加減). As a result, we got the attentive effect and report on a paper.

• Journal of Welding and Joining
• /
• v.32 no.6
• /
• pp.75-81
• /
• 2014

Usage of heavy metal element (Pb, Hg and Cd etc.) in electronic devices have been restricted due to the environmental banning of the European Union, such as WEEE and RoHS. Therefore, it is needed to develop the Pb-free solder plated ribbon in photovoltaic (PV) module. This study described that degradation characteristics of PV module under damp heat (DH, $85^{\circ}C$ and 85% R.H.) condition test for 1,000 h. Solar cell ribbons were utilized to hot dipping plate with Pb-free solder alloys. Two types of Pb-free solder plated ribbons, Sn-3.0Ag-0.5Cu (SAC305) and Sn-48Bi-2Ag, and an electroless Sn-40Pb solder hot dipping plated ribbon as a reference sample were prepared to evaluate degradation characteristics. To detect the degradation of PV module with the eutectic and Pb-free solder plated ribbons, I-V curve, electro-luminescence (EL) and cross-sectional SEM analysis were carried out. DH test results show that the reason of maximum power (Pm) drop was mainly due to the decrease fill factor (FF). It was attributed to the crack or oxidation of interface between the cell and the ribbon. Among PV modules with the eutectic and Pb-free solder plated ribbon, the PV module with SAC305 ribbon relatively showed higher stability after DH test than the case of PV module with Sn-40Pb and Sn-48Bi-2Ag solder plated ribbons.