• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.87-87
• /
• 2007

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.138-141
• /
• 2004

Finite element method is very effective method to simulate the forming processes with good prediction of the deformation behaviour. For the finite element modeling of sheet mental forming the accurate tool model is required. Due to the geometrical complexity of real-size part stamping tools it is hard to make FE model for real-size auto-body stamping parts. In this paper, it was focussed on the drawability factors on auto-body panel stamping by AUTOFORM with using tool planing alloy to reduce law price as well as high precision from Design Optimization of die. According to this study, the results of simulation will give engineers good information to access the Design Optimization of die.

• Journal of Wetlands Research
• /
• v.25 no.2
• /
• pp.91-98
• /
• 2023

Some concrete wastewater generated during construction is in the form of non-point pollution sources that workers, managers, and users are unaware of, and it is not easy to manage as it flows through sewage pipes. Due to these characteristics, construction sludge is inflow into rivers and sewage pipes in the form of non-point pollution sources in an unmanaged state. This study applied the D.W.S method to the concrete retaining wall removal method installed on the road, and the resulting concrete wastewater was physically and chemically treated through a mobile sewage treatment facility, and it was examined whether it met the removal efficiency and wastewater discharge acceptance standards. Accordingly, it is intended to meet the standards for effluent concentration of wastewater during construction by removing 73.5% of BOD and 89.1% of SS through physical and chemical treatment through portable sewage treatment facilities during construction. In addition, we would like to review the adequacy and economic analysis of calculating environmental conservation costs for physicochemical treatment through portable sewage treatment facilities and sewage treatment generated during construction.

• Proceedings of the KIEE Conference
• /
• 2008.04b
• /
• pp.22-24
• /
• 2008

다도체 송전선로에서 전선 간격 유지 및 진동을 완화시켜주는 역할을 하는 스페이서댐퍼가 손상 받게 되면 즉시 유지보수 및 교체 작업을 하여야 한다. 그러나 이러한 작업은 송전선로 위에서 이루어지므로 전선의 장력과 작업자의 하중으로 인해 유지보수 및 교체작업이 매우 어렵고, 작업시간이 많이 소요되며, 전선표면손상, 스페이서댐퍼의 위치 변동 및 무리한 작업으로 인한 작업안전성 저하 등의 문제점이 있다. 따라서, 상기한 문제점을 해소하고 작업 효율의 상승을 위하여 작업시 각 전선의 간격을 쉽게 벌리고 좁힐 수 있는 작업용 공구인 스페이서지그(Spacer Jig)와 이를 이용한 송전선로의 스페이서댐퍼 유지보수 및 교체공법을 개발하여 교체작업시간 단축 및 작업안전성을 향상시킨 우수한 기술을 개발하였다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.1
• /
• pp.16-24
• /
• 2018

In this study, an experiment was conducted to analyze mortar based rheology for 3D printing method application. The tendency of rheological properties due to the change of W/B, binder type, replacement ratio, and super plasticizer which have a great influence on the flow characteristics of concrete was experimentally analyzed. Experiments were carried out by dividing into paste and mortar. In the paste experiment, rheology was analyzed by setting W/B, binder type, replacement ratio, and super plasticizer dosage as main variables. In the mortar experiment, the rheological properties of W/B and sand ratio were analyzed. As a result, as the W/B was increased, the viscosity decreased and the FA ratio to replace FA increased and the viscosity increased. In order to increase the fluidity, substitution of only 5% of SF reduces the shear stress and the viscosity is reduced by about 83%. Mortar rheological evaluation shows that there is a critical section where a large change occurs in the W/B 30 to 40% section. Also, in the same W/B, it is analyzed that there is a critical section where the shear stress increases more than twice in the sand ratio of 50~60%.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.206.2-206.2
• /
• 2005

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.1351-1352
• /
• 2011

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.285-286
• /
• 2006

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.32-35
• /
• 2004

The development of automotive rear chassis part using tube forming process has advantage of increase in part durability and decrease in its weight. We developed tubular type rear CTBA(Coupled Torsion Beam Axle) part with 60K high strength steel developed by POSCO in this project. The result was demonstrated that tubular type CTBA shows excellent durability performance and $10\%$ weight reduction compared with V-beam type CTBA in our work. Furthermore, we will adapt this technology to mass production and apply to the other chassis parts.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.155-157
• /
• 2006

송전전압이 점차 초고압화되면서 절연체의 유전특성을 개선하여 송전용량을 향상시키고, 절연내력을 높여 케이블 외경을 저감시키려는 시도에 따라 우수한 유전특성 및 절연내력을 갖는 폴리머 절연층과 기계적 특성, 절연유와의 적합성이 우수한 크라프트지의 장점을 혼합시킨 반합성지가 개발되어 전력케이블의 주절연재료로 사용되고 있다. 본 논문은 LS전선이 국내최초로 개발한 400 kV급 반합성지 전력케이블 및 접속함 개발과정 및 이와 관련된 요소기술에 대해 기술하였다. 송전시스템에서 요구되는 유전특성의 반합성지를 설계 제작하여, 기존 크라프트 절연지 대비 유전손실은 50% 수준, 절연내력은 125%이상의 반합성지를 개발하였고, 반합성지 고유의 특성인 팽윤율을 조절하여 케이블을 제조하였다. 반합성지 절연 케이블에 필요한 접속함에서는 보강절연재로 케이블과 동일한 반합성지를 사용하여 전체적인 3기를 감소시키고, 열저항성을 줄이고자 노력하였다. 또한, 접속함 조립공정에 필요한 저온연공법을 개발하여 반합성지에 열적 스트레스를 최소화하였다. 상기 관련기술의 개발 결과로, IEC 60141, AEIC CS2-97 및 NGTS 3.5.1에 근거하여 400 kV급 반합성지 OF 케이블 및 접속함에 대해 국제 공인기관인 KEMA의부터 Type Test을 인증받았다.