• Journal of Korea Water Resources Association
• /
• v.37 no.3
• /
• pp.219-231
• /
• 2004

The use of air diffuser system to ameliorate the reservoir by breaking stratification is now widespread. This study focuses on the hydrodynamic behavior of bubble plumes, which is the major mechanism of destratification and their combined effect of adjacent plumes on destratification efficiency. By introducing 2-phase Computational Fluid Dynamics(CFD) technique, we could suggest the optimal diffuser spacing having optimal destratification efficiency by simply analyzing the complex destratification procedures varying with the seasonal stratification intensity and bubble flow rate. Lab experiments were also carried out to verify CFD model in thermally stratified fresh water which quite differs from former researches using salts. This study showed that the mixing efficiency strongly depends on the spacing of neighboring plumes. When diffuser spacing is lower than 1.5 times the depth, the combined effect is stronger; as Plume Number(PN) is increased, the efficiency is strongly affected by spacing. If the distance is shorter than the depth of water, the efficiency increases linearly in proportion to PN. Otherwise, the efficiency increases non-linearly. These findings suggest that the combined effect should be more quantitatively taken into consideration for design and operation of air-diffuser destratification system, and recommend that the optimal destratification efficiency will be when plume number is 1000 and the spacing between neighboring diffusers is 1.5 times the depth.

• KIEE International Transaction on Systems and Control
• /
• v.2D no.2
• /
• pp.78-91
• /
• 2002

In the thermal power plant, there are six manipulated variables: main steam flow, feedwater flow, fuel flow, air flow, spray flow, and gas recirculation flow. There are five controlled variables: generator output, main steam pressure, main steam temperature, exhaust gas density, and reheater steam temperature. Therefore, the thermal power plant control system is a multinput and output system. In the control system, the main steam temperature is typically regulated by the fuel flow rate and the spray flow rate, and the reheater steam temperature is regulated by the gas recirculation flow rate. However, strict control of the steam temperature must be maintained to avoid thermal stress. Maintaining the steam temperature can be difficult due to heating value variation to the fuel source, time delay changes in the main steam temperature versus changes in fuel flow rate, difficulty of control of the main steam temperature control and the reheater steam temperature control system owing to the dynamic response characteristics of changes in steam temperature and the reheater steam temperature, and the fluctuation of inner fluid water and steam flow rates during the load-following operation. Up to the present time, the Proportional-Integral-Derivative Controller has been used to operate this system. However, it is very difficult to achieve an optimal PID gain with no experience, since the gain of the PID controller has to be manually tuned by trial and error. This paper focuses on the characteristic comparison of the PID controller and the modified 2-DOF PID Controller (Two-Degrees-Freedom Proportional-Integral-Derivative) on the DCS (Distributed Control System). The method is to design an optimal controller that can be operated on the thermal generating plant in Seoul, Korea. The modified 2-DOF PID controller is designed to enable parameters to fit into the thermal plant during disturbances. To attain an optimal control method, transfer function and operating data from start-up, running, and stop procedures of the thermal plant have been acquired. Through this research, the stable range of a 2-DOF parameter for only this system could be found for the start-up procedure and this parameter could be used for the tuning problem. Also, this paper addressed whether an intelligent tuning method based on immune network algorithms can be used effectively in tuning these controllers.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.7
• /
• pp.667-678
• /
• 2002

In this paper, a new radiating structure with a multi-layered two-dimensional metallic disk array was proposed for shaping the flat-topped element pattern. It is an infinite periodic planar array structure with metallic disks finitely stacked above the radiating circular waveguide apertures. The theoretical analysis was in detail performed using rigid full-wave analysis, and was based on modal representations for the fields in the partial regions of the array structure and for the currents on the metallic disks. The final system of linear algebraic equations was derived using the orthogonal property of vector wave functions, mode-matching method, boundary conditions and Galerkin's method, and also their unknown modal coefficients needed for calculation of the array characteristics were determined by Gauss elimination method. The application of the algorithm was demonstrated in an array design for shaping the flat-topped element patterns of $\pm$20$^{\circ}$ beam width in Ka-band. The optimal design parameters normalized by a wavelength for general applications are presented, which are obtained through optimization process on the basis of simulation and design experience. A Ka-band experimental breadboard with symmetric nineteen elements was fabricated to compare simulation results with experimental results. The metallic disks array structure stacked above the radiating circular waveguide apertures was realized using ion-beam deposition method on thin polymer films. It was shown that the calculated and measured element patterns of the breadboard were in very close agreement within the beam scanning range. The result analysis for side lobe and grating lobe was done, and also a blindness phenomenon was discussed, which may cause by multi-layered metallic disk structure at the broadside. Input VSWR of the breadboard was less than 1.14, and its gains measured at 29.0 GHz. 29.5 GHz and 30 GHz were 10.2 dB, 10.0 dB and 10.7 dB, respectively. The experimental and simulation results showed that the proposed multi-layered metallic disk array structure could shape the efficient flat-topped element pattern.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.9
• /
• pp.40-49
• /
• 2011

Integrating massive components and low-power policies have been actively investigated for system-on-chip designs. But in recent years, finding the optimal interconnection structure among heterogeneous components has emerged as a critical system design issue. Therefore, various simulation tools to model interconnection designs are being developed and performance evaluation of simulation is reflected in the real design. But most of the simulation environments employ traffic generation based on the mathematical probability functions, and such traffic generation cannot fully cover for various situations that may be occurred in the real system. Therefore, the demand for traffic pattern generation based on real applications is increasing. However, there have been few simulators that adopt application-specific traffic generators. This paper proposes a novel traffic generation method in simulating various interconnection structures for multi-processor system-on-chip design. The proposed traffic generation method can generate traffic patterns that can reflect the actual characteristics of the application and evaluate the performance of an interconnection structure under more realistic circumstance than traffic patterns using mathematical probability functions. By comparing the differences between the proposed method and the one based on mathematical probability functions, this paper shows advantages of the proposed traffic generation method.

• Asian-Australasian Journal of Animal Sciences
• /
• v.20 no.8
• /
• pp.1236-1242
• /
• 2007

Sixty healthy growing pigs ($Duroc{\times}Landrace{\times}Yorkshire$ with an average BW of 21.4 kg) were used to determine the true digestible phosphorus (TDP) requirement of growing pigs on the basis of growth performance and serum biochemical indices. Pigs were assigned randomly to one of five dietary treatments (12 pigs/diet), representing five levels of TDP (0.16%, 0.20%, 0.23%, 0.26% and 0.39%). There were three replications per treatment, with four pigs (2 barrows and 2 gilts) in each replication (2 pigs/pen) A randomized-block design was used, with pen as the experimental unit. Experimental diets were formulated to provide the 5 TDP levels with a total calcium (Ca) to TDP ratio of 2:1, and offered to pigs at 5% BW for 28 d. The total Ca contents of the five diets were 0.33, 0.38, 0.45, 0.51 and 0.79%, respectively. During the 28-d experimental period, the ADG of pigs was affected by dietary TDP levels as described by Equation 1: y = $-809,532x^4+788,079x^3-276,250x^2+42,114x-1$,759; ($R^2$ = 0.99; p<0.01; y = ADG, g/d; x = dietary TDP, %). The feed:gain ratio for pigs was affected by dietary TDP levels as described by Equation 2: y = $3,651.1x^4-3,480.4x^3+1,183.8x^2-172.5x+10.9$ ($R^2$ = 0.99; p<0.01; y = feed:gain ratio; x = dietary TDP, %). Total P concentrations in serum were affected by dietary TDP levels as described by Equation 3: y = $-3,311.7x^4+3,342.7x^3-1,224.6x^2+195.6x-8.7$ ($R^2$ = 0.99; p<0.01; y = total serum P concentration and x = dietary TDP, %). The highest ADG (782 g/d), the lowest feed:gain ratio (1.07), and the highest total serum P concentration (3.1 mmol/L) were obtained when dietary TDP level was 0.34%. Collectively, these results indicate that the optimal TDP requirement of growing pigs is 0.34% of the diet (e.g., 5.1 g/day for a 30-kg pig that consumed 1.5 kg feed daily) at a total Ca to TDP ratio of 2:1.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.18 no.4
• /
• pp.338-347
• /
• 2006

A small hydro-power plant using the seawater used as the cooling (circulated) water and discharged is under construction. The bigger size of the small hydro-power plant, the better in order to maximize the efficiency and the electric power. The optimal size, however, should be determined in the constraints of the channel un-disturbed range. The water level change should be checked in detail based on the hydraulic behaviour. In this study, the FLOW3D model, three-dimensional flow model, is setup using the flow measurement data in the effluent discharge channel and the flow pattern changes due to the small hydro-power plant construction are predicted by the model. The plant construction makes the increasing of the water level, and the water level in the upstream of the channel weir is increased 65 cm from 4.32 m to 4.97 m, in the condition of the design discharge $156m^3/s$ and the movable weir height of the hydro-power plant 3.8 m.

• Spatial Information Research
• /
• v.23 no.4
• /
• pp.13-22
• /
• 2015

There has been much interest in the VWorld open platform with the addition of a variety of contents or services such as 2D map, 3D terrain, 3D buildings, and thematic map since 2012. However, the VWorld system architecture was not stable for the system overload. For example, the system was stopped due to the rapidly increasing user accesses when the 3D terrain service of the North Korea and the Baekdu mountain was launched at September 2012 and September 2013, respectively. It was because the system architect has just extended the server system and the network bandwidth whenever the rapid increase of user accesses occurs or new service starts. Therefore, this study proposes a new VWorld system architecture that can reliably serve the huge volume of National Spatial Data by applying the new technologies such as CDN, visualization and clustering. Finally, it is expected that the results of this study can be used as a basis for the next VWorld system architecture being capable of a huge volume of spatial data and users.

• Journal of Bio-Environment Control
• /
• v.31 no.4
• /
• pp.485-496
• /
• 2022

Modern agriculture is being transformed into smart agriculture to maximize production efficiency along with changes in the 4th industrial revolution. However, rural areas in Korea are facing challenges of aging, low fertility, and population outflow, making it difficult to transition to smart agriculture. Among ICT technologies, simulation allows users to observe or experience the results of their choices through imitation or reproduction of reality. The combination of the three-dimension (3D) model and the greenhouse simulator enable a 3D experience by virtual greenhouse for fruits and vegetable cultivation. At the same time, it is possible to visualize the greenhouse under various cultivation or climate conditions. The objective of this study is to apply the greenhouse climate management model for simulation development that can visually see the state of the greenhouse environment under various micrometeorological properties. The numerical solution with the mathematical model provided a dynamic change in the greenhouse environment for a particular greenhouse design. Light intensity, crop transpiration, heating load, ventilation rate, the optimal amount of CO₂ enrichment, and daily light integral were calculated with the simulation. The results of this study are being built so that users can be linked through a web page, and software will be designed to reflect the characteristics of cladding materials and greenhouses, cultivation types, and the condition of environmental control facilities for customized environmental control. In addition, environmental information obtained from external meteorological data, as well as recommended standards and set points for each growth stage based on experiments and research, will be provided as optimal environmental factors. This simulation can help growers, students, and researchers to understand the ICT technologies and the changes in the greenhouse microclimate according to the growing conditions.

• Composites Research
• /
• v.34 no.4
• /
• pp.241-248
• /
• 2021

As the electric vehicle market grows, there is an issue of light weight vehicles to increase battery efficiency. Therefore, it is going to replace the battery module cover that protects the battery module of electric vehicles with high strength/high heat-resistant polymer composite material which has lighter weight from existing aluminum materials. It also aims to respond to the early electric vehicle market where technology changes quickly by combining 3D printing technology that is advantageous for small production of multiple varieties without restrictions on complex shapes. Based on the composite material mechanics, the critical length of glass fibers in short glass fiber (GF)/polycarbonate (PC) composite materials manufactured through extruder was derived as 453.87 ㎛, and the side feeding method was adopted to improve the residual fiber length from 365.87 ㎛ and to increase a dispersibility. Thus, the optimal properties of tensile strength 135 MPa and Young's modulus 7.8 MPa were implemented as GF/PC composite materials containing 30 wt% of GF. In addition, the filament extrusion conditions (temperature, extrusion speed) were optimized to meet the commercial filament specification of 1.75 mm thickness and 0.05 mm standard deviation. Through manufactured filaments, 3D printing process conditions (temperature, printing speed) were optimized by multi-optimization that minimize porosity, maximize tensile strength, and printing speed to increase the productivity. Through this procedure, tensile strength and elastic modulus were improved 11%, 56% respectively. Also, by post-processing, tensile strength and Young's modulus were improved 5%, 18% respectively. Lastly, using the FEA (finite element analysis) technique, the structure of the battery module cover was optimized to meet the mechanical shock test criteria of the electric vehicle battery module cover (ISO-12405), and it is satisfied the battery cover mechanical shock test while achieving 37% lighter weight compared to aluminum battery module cover. Based on this research, it is expected that 3D printing technology of polymer composite materials can be used in various fields in the future.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.5
• /
• pp.1-14
• /
• 2015

In case of a gas turbine engine for supersonic operation, the engine have a wide range of operating inlet mass flow rate and required high performance such as thrust and fuel consumption. Therefore, variable system and its optimal control logic are essentially needed. In this work, a method for performance prediction of a gas turbine engine with variable system compressor and its control scheme were developed. Conceptual design of compact acuation system for the operation of the variable system was also conducted. The performance of a low-bypass ratio mixed flow turbofan engine was analyzed, and it was observed that the surge margin of the engine is improved at off-design condition by applying the control scheme.