• 콘크리트학회지
• /
• 제7권1호
• /
• pp.117-125
• /
• 1995

철근과 콘크리트의 부착성능에 영향을 미치는 인자들을 평가하기 위하여 부착실험을 수행하였다. 주요변수로는 콘크리트의 압축강도($f_c$'=340, 460, 650, $904kg/cm^2$), 콘크리트의 피복두께(25, 38, 51, 105, 110mm), 철근의 직경(D13, D22)으로 하였으며 구속철근의 효과와 철근간격은 고려하지 않았다. 철근이 일축인장력을 받을 때 철근의 전 부착길이에 걸쳐 응력이 일정하다는 가정하에 32개의 실험체를 제작, 실험하였다. 각 실험체별로 파괴모드를 고찰하였고, 부착응력.변위관계를 통하여 변수의 영향을 평가하였으며, 실험결과에 다른 최대부착응력을 ACI 규준의 상한선($700kg/cm^2$)을 초과하여도 부착응력 및 최대 부착응력이 증가하는 것으로 나타나 콘크리트 압축강도 상한선을 초과하는 경우 정착길이 산정시 압축강도 증가에 따른 영향을 고려하여야 하는 것으로 나타났다.

• 한국자동차공학회논문집
• /
• 제21권3호
• /
• pp.82-87
• /
• 2013

In this work, the 1L grade integrated metal DOC/DPF filter that can install in engine manifold position was developed to investigate the effect of platinum-coating amount of filter on the improvement of filter activation temperature and reduction of particulate matter (PM). This filter was installed in 2.9L CI engine which meets the EURO-4 emission regulation. Tests for PM reduction efficiency of filter were conducted under ND-13 mode with full-load test condition. It was revealed that the time to reach the activation temperature of metal filter ($280^{\circ}C$) was shorter as the amount of platinum-coating increased. This short activation time can be helpful for the reduction of CO and HC emissions during cold start condition. At the same time, PM reduced as the coating amount increased. The reduction percentage of $DOC_{40}$, $DOC_{20}$, and $DOC_0$ were 96.7% (2.34 mg/kW'h), 95.1% (3.47 mg/kW'h), and 94.5% (3.69 mg/kW'h) compared to previous result (71.4 mg/kW'h), respectively.

• 한국기계가공학회지
• /
• 제16권5호
• /
• pp.13-18
• /
• 2017

In this work the augmented safety of Type 4 composite vessel in accordance with uniform-stress design has been demonstrated through a series of burst tests and structural analyses. For this end, three sample vessels were used: (1) designed as guided by the isotensoid dome theory (called iso-dome cylinder); (2) with dome longer compared to uniform-stress design (called prolate cylinder); and (3) with dome wider than uniform-stress design (called oblate cylinder). Structural analyses have been performed using ABAQUS finite element code based on the periodic symmetry to circumferential direction. As a result, the maximum stresses are induced around the bodies of all three cylinders. However, the analyses, with the assumption of possible defect demonstrate that the maximum stresses are induced around the dome knuckles for the prolate and the oblate cylinders. The results of the burst tests for the three cylinders show that the burst initiates from the cylinder body of the iso-dome cylinder and from the dome knuckles of the prolate and the oblate cylinders. Finally, it is recommended that, to comply with DOT CFFC 2007, the dome shape should be designed and fabricated as guided by the isotensoid dome theory.

• 한국분말재료학회지
• /
• 제14권1호
• /
• pp.13-18
• /
• 2007

The mother Ni-W (1-5 wt.%) alloy billets for coated conductor substrate were fabricated by powder metallurgy process. The tensile test results for the sintered Ni-W rods showed the increase of mechanical strength and decrease of ductility with increasing W content due to the solid solution hardening. All the fracture surfaces of the tested specimens showed the typical ductile fracture mode of dimple rupture due to the local necking. The Ni-W alloy billets were made into tape by cold rolling. After the appropriate heat treatment for recrystallization, the brass texture formed by the cold rolling was converted to the complete cube texture. The in-plane and out of plane texture of the tapes estimated by x-ray pole figure were smaller than 9 degree and 7 degree, respectively. The effect of the W addition on the texture development seems not to be significant.

• 한국자동차공학회논문집
• /
• 제13권2호
• /
• pp.108-113
• /
• 2005

The damageability and repairability of similar platform type vehicles could be very concerned with design optimization. In all the vehicles crash tested, small size passenger vehicles were weakness in aspect of damageability and repairability. The most critical area appears to be repair cost considering that parts cost is the largest portion of total repair cost segments. Besides repair cost, attaching method of front sidemember and subframe are placed special importance for impact energy absorption and damageability and repairability. So in order to improve damageability and repairability of vehicle structure and body component of the monocoque type passenger vehicles, the end of front side member and front back beam should be designed with optimum level and to supply the end of front side member as a partial condition approx 300mm. The effectiveness of design concept on the 40% offset frontal impact characteristics of the passenger vehicle structure is investigated and summarized.

• Steel and Composite Structures
• /
• 제11권6호
• /
• pp.469-488
• /
• 2011

This paper consists of two parts; the first part describes the laboratory work concerning the behavior of lightweight aggregate concrete filled steel tubes (LACFT). Based on eccentricity tests, fifty-four specimens with different slenderness ratios (L/D= 3, 7, and 14) were tested. The main parameters varied in the test are: load eccentricity; steel ratio; and slenderness ratio. The standard load-strain curves of LACFT columns under eccentric loading were summarized and significant parameters affecting LACFT column's bearing capacity, failure mechanism and failure mode such as confinement effect and bond strength were all studied and analyzed through the comparison with predicted strength of concrete filled steel tube columns (CFT) using the existing codes such as AISC-LRFD (1999), CHN DBJ 13-51-2003 (2003) and CHN CECS 28:90 (1990). The second part of this paper presents the results of parametric study and introduces a practical and accurate method for determination of the maximum compressive strength of confined concrete core ($f_{max}$), In addition to, the study of the effect of aspect-ratio and length-width ratio on the yield stress of steel tubes ( $f_{sy}$) under biaxial state of stress in CFT columns and the effect of these two factors on the ultimate load carrying capacity of axially loaded CFT/LACFT columns.

• Journal of Welding and Joining
• /
• 제33권4호
• /
• pp.37-43
• /
• 2015

Characteristics of dissimilar metal welds between STS 316L and carbon steel ASTM A516 Gr.70 made with GTAW have been evaluated in terms of microstructure, ferrite content, chemical analysis, hardness and corrosion resistance. Three heat inputs of 9.00, 11.25, 13.00kJ/cm were employed to make joints of dissimilar metals with ER309 wire. Based on microstructural examination, the amount of vermicular type of ${\delta}$-ferrite was increased with increasing heat input due to the increase of Creq/Nieq in the second layer of welds. Based on the EDX analysis of weld metals, Cr and Ni content in the 2nd layer increased while those content in the first layer of welds decreased with heat inputs. Cellular solidification mode in the 1st layer and dendritic solidification mode in the 2nd layer due to different cooling rates were prevailed, respectively. Heat affected zone which formed hard microstructure showed higher hardness than the weld metal. The salt spray test of dissimilar metals weld joints showed that the carbon steel surfaces only corroded. The weight loss rate due to corrosion increased up to 100hours but it decreased above 100 hours. There was little difference in the weight loss caused by corrosion regardless of heat inputs.

• 보건교육건강증진학회지
• /
• 제11권2호
• /
• pp.33-47
• /
• 1994

AIDS preventional efforts need to be guided by well trained health care personnel especially by school nurses for the adolescents. This study was designed to get basic data about AIDS educational program development for school nurses. The objectives of this study were to 1) identify AIDS knowledg of school nurses 2) identify AIDS attitudes of school nurses and 3) identify association between AIDS knowledge and sociodemographic characteristics. Data were collected from 173 subjects in Chonbuk province. Self-reporting questionnaire were administered during the period from 1st of June to 30th of June, 1994. AIDS related knowledge was measured by using 44 questions on cause(3 items), testing(3 items), mode of transmission(15 items), clinical manifestations(5 items), treatment(3 items), prevention(5 items), complication(4 items), infection control(3 items) and Using resources(3 items). AIDS related attitudes were measured by five point Likert scales using 13 questions on perceived threats from AIDS crisis (4 items), perceived severity to AIDS(2 items), perceived needs about psychosocial care for HIV infected patients(3 items) and perceived educational needs of AIDS(4 items). The collected data were analyzed by SPSS/PC/sup +/, using percentages, Mean and S.D. descriptive purpose and t-test or F for comparing the variables. The major findings were as follows: 1. Respondents ranged in knowledge of AIDS between 0 and 44 with the 33.79 mean score. Percentage of correctly answered respondents to each categories - mode of transmission : 87.0% - clinical manifestation : 85.0% - cause : 82.5% - prevention : 81.5% - treatment : 76.1% - infection control : 72.8% - testing of HIV infection 71.8% - using community resourses : 50.9% - complication : 45.8% 2. The respondents' attitudes of AIDS The majority(70%) showed higher perceived threat The majority(91.3%) showed higher perceived severity to AIDS crisis As a whole, perceived needs about psychosocial care for HIV infected patients negative The majority (over 96.5%) showed highly perceived educational needs of AIDS. 3. The relationship between AIDS knowledge and each of those general character. AIDS knowledge shows significant difference with age(F=3.50, p<.016), years of professional experience(F=4.14, p<.007) and received lecture about AIDS(F=4.54, p<.000). There was no significant difference between AIDS knowledge and job satisfaction.

• 전자공학회논문지
• /
• 제51권9호
• /
• pp.82-90
• /
• 2014

본 논문에서는 선형성을 가진 파노라믹 스캔 라이다(PSL) 시스템용의 4-채널 차동 트랜스임피던스 증폭기 어레이를 0.18-um CMOS 공정을 이용하여 구현하였다. PSL시스템을 위한 성능의 비교분석을 위하여 전류모드 및 전압모드의 두 종류 트랜스임피던스 어레이 칩을 각각 구현하였으며, 채널당 1.25-Gb/s 동작속도를 갖도록 설계하였다. 먼저 전류모드 칩의 경우, 각 채널 광 수신입력단은 전류미러 구조로 구현하였으며, 특히 로컬 피드백 입력구조로 개선하여 낮은 입력저항과 낮은 잡음지수를 가질 수 있도록 설계하였다. 칩 측정 결과, 채널 당 $69-dB{\Omega}$ 트랜스임피던스 이득, 2.2-GHz 대역폭, 21.5-pA/sqrt(Hz) 평균 잡음 전류 스펙트럼 밀도, -20.5-dBm 수신감도, 및 1.8-V 전원전압에서 4채널 총 147.6-mW 소모전력을 보이며, 1.25-Gb/s 동작속도에서 크고 깨끗한 eye-diagram을 보인다. 한편, 전압모드 칩의 경우, 각 채널 광 수신입력단은 인버터 입력구조로 구현하여 낮은 잡음지수를 갖도록 설계하였다. 칩 측정 결과, 채널 당 $73-dB{\Omega}$ 트랜스임피던스 이득, 1.1-GHz 대역폭, 13.2-pA/sqrt(Hz) 평균 잡음 전류 스펙트럼 밀도, -22.8-dBm수신감도, 및 4채널 총 138.4-mW 소모전력을 보이며, 1.25-Gb/s 동작속도에서 크고 깨끗한 eye-diagra을 보인다.

• 한국자동차공학회논문집
• /
• 제24권4호
• /
• pp.480-486
• /
• 2016

Manufacturers have been applying several technologies that can improve the fuel economy of their cars. The regulated voltage control(RVC) system, is one of those technologies being used in passenger cars. In RVC, the voltage of an alternator is controlled depending on the electrical load demand or battery SOC, although each manufacturer differs from another in terms of detail. RVC can reduce the load of an alternator by consuming the stored energy of a battery and simultaneously generate energy. In this paper, a diesel passenger car equipped with an RVC system was tested under FTP-75 and HWFET modes to evaluate fuel economy as their initial battery SOC(100, 90, 80 and 60 %). The test results showed that the initial SOC affects fuel economy only under the FTP-75 mode. FTP-75 fuel economy of the 60% SOC was 13.2 % lower than the 100 % SOC. Also, the simultaneous consumption of the two energy sources did not appear in 60 % SOC.