• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1509_1510
• /
• 2009

This paper presents the design and simulation results of ohmic contact RF MEMS silicon switch with a high isolation at high frequencies along with the position of a contact part, initial off-state and intermediate off-state including the state where a contact part is placed right over a signal line of coplanar waveguide (CPW). The ohmic contact part is connected with comb drives made of high resistivity single crystalline silicon. The released contact part is $30{\mu}m$ apart from the edge of signal line on the glass substrate along the lateral direction (x-direction) at initial off-state. The electrostatic force of the comb electrode creates the x-directional movement thus initial state is converted to the intermediate off-state. The initial off-state of the switch results in isolations of -31 dB, -24 dB and reflections of -0.45 dB, -0.67 dB at 50 GHz and 110 GHz, respectively. It shows the isolation degradation when the contact part moves right over the signal line of CPW like an initial off-state of a conventional MEMS switch. The isolations and reflections are -31 dB, -24 dB and -0.50 dB, -1.31 dB at 50 GHz and 110 GHz, respectively at the intermediate off-state.

• Journal of Advanced Navigation Technology
• /
• v.4 no.2
• /
• pp.182-190
• /
• 2000

In this paper, interference effects between NGSO and HAPS in the feeder link have been simulated and analyzed by means of calculating excess time percent and duration below the ell protection ratio. As the results, in the case of HAPS interference into NGSO, it can be obtained that the lowest C/I values are 20.42dB in 50km and 12.73dB in 20km of HAPS altitudes, respectively. And in the case of NGSO interference into HAPS, it can be obtained that the lowest ell values are 13.94dB and 10.42dB respectively. HAPS system has more interference reception from other systems or effects more interference into other systems as its altitude is lower. Also, the lowest ell values are appeared at difference time with its altitude.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.7
• /
• pp.1-14
• /
• 1996

Effects of the external optical feedback on the optical transmission characteristics were evaluated for 3 kinds of commercialized DFB-LD modules for 2.5Gbps optical communication systems. As a result, intensity noise induced by external optical feedback via generating the external cavity modes deteriorated the transmission performances of sthe DFB-LD modules as much as 1.5dB, 1.2dB, and 1.0dB for the maximum feedback ratio of -8.8dB which corresponds to the worst reflection along the fiber transmission line. Additional penalty of 0.5dB was occurrred when state of polarization of feedback light was adjusted. From the experiments evaluating the isolation ratio of the single polarization optical isolator, decrease of the polarization dependent isolation ratio as much as 10dB from that of specification and the effective isolation ratio as much as 20dB from that of specification was mjor cause of high sensitivity of DFB-LD modules to external feedback. It was suggested that polarization independent optical isolator or single polarization optical isolator with isolation ratio specification of more than 40dB is required for 2.5Gbps DFB-LD modules with complete suppression of external feedback effects.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.3
• /
• pp.68-73
• /
• 2011

In this paper, a compact-narrow open stub band-pass filter with parasitic-signal of low frequency range and second harmonics rejected using the parallel coupled line and FLCLM(Frquency Locked Controlled Length Method) is proposed. The characteristic of the parallel coupled line can be rejection for parasitic-signal of low frequency range and second harmonics. In last filter of experimental results show that insertion loss is 1.2 dB and return loss is 14.8 dB, and the fractional bandwidth is 10 % at the center frequency of 5.8 GHz. In additional, the rejection for parasitic-signal of low frequency range and second harmonics are 28.9 dB and 28.8 dB, respectively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.282-285
• /
• 2006

This study is to examine bond strength of beam reinforced with GFRP rebar under 4-point bending test by adopting BRITISH STANDARD. The variables were made to have bonding length of 5times$(5d_b)$, 10times$(10d_b)$ and 15times$(15d_b)$ of the nominal diameter of GFRP rebar and were done to analyze the relationship between the bonding strength and the slip. In the result of the test, pull-out failure was dominant in the $5d_b$ and $10d_b$ specimen, both patterns of the pull-out failure and concrete splitting failure appeared in the $10d_b$. On the other hand, the $15d_b$ specimen showed only concrete splitting failure at the end of bonding length. Therefore, it was prove that available bonding length of the GFRP rebar under bending condition on static test is over $15d_b$ then farther research such as fatigue bending test, development of bonding model, FEM parameter study should be performed.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.9
• /
• pp.651-657
• /
• 2003

We have demonstrated an in-line polarization splitter based on a side-polished fiber coupler including a thin metal intermediate layer. The experimental results revealed that the metal layer with proper thickness prevents TE polarization component from optical coupling between two contacted side-polished fibers, whereas it allows TM polarization component to the coupling. The design and fabrication techniques about the polarization splitter exploiting the side-polished fibers have been presented. The fabricated polarization splitter exhibited 18dB and 23dB of isolation ratio for TE polarization and TM polarization, respectively. The measured insertion loss for TE and TM polarization was 0.7dB and 1.3dB, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.2 s.93
• /
• pp.167-173
• /
• 2005

The isolation of the series PIN diode switch is restricted by the parallel capacitance of PIN diode and the switch driver circuit limits switching speed of PIN diode switch. To overcome these problems, a high isolation and high switching speed Pin diode switch is proposed adapting the parallel resonant inductance and TTL compatible switch driver circuit. The measurement results of the 3 GHz PM diode switch show 1 GHz frequency band, less than 1.5 dB insertion loss, 65 dB isolation, more than 15 dB return loss and less than 30 ns switching speed. In particular the 3 GHz PIN diode switch using the parallel resonant inductance exhibits the improvement of isolation by 15 dB.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.34-38
• /
• 2000

In this paper, interference effects between NGSO and HAPS in the feeder link have been simulated and analyzed by means of calculating excess time percent and duration below the C/I protection ratio. As the results, in the case of HAPS interference into NGSO, it can be obtained that the lowest C/I values are 27.42dB in 50km and 12.73dB in 20Km of HAPS altitudes, respectively. And in the case of NGSO interference into HAPS, it can be obtained that the lowest C/I values are 13.94dB and 10.42dB respectively. HAPS system has more interference reception from other systems or effects more interference into other systems as its altitude is lower. Also, the lowest C/I values are appeared at difference time with its altitude.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.3
• /
• pp.74-78
• /
• 2011

In this paper, the bandpass filter for ITS system of 5.8 GHz is proposed by using the dual-mode resonator with the radial stub. As alternating the open stub with the radial stub, the size of the dual mode resonator can be reduced about 39.6% and the out-of-band characteristics of the bandpass filter using dual mode resonator can be enhanced from 19.4 dB to 29.1 dB by using the stub of $6.9{\Omega}$ i.e. realized by parallel two radial stubs with $60^{\circ}$ angle. The fabricated bnadpass filter using the dual mode resonator has the center frequency of 5.72 GHz with the fractional bandwidth of 4.1%. Also, the filter has the insertion loss and return loss of 1.79 dB and 19.4 dB, respectively.

• Journal of the Korea Society of Computer and Information
• /
• v.16 no.10
• /
• pp.131-136
• /
• 2011

In this paper, we fabricate multi channel receiver for radar system. This receiver at X-band can be received 8 signal of an identical characteristic, dynamic range has more than 80[dB]. To process direct received signals, this system has the built-in two digital de-modulators which offer the minimum loss on the receiving signal path and has high stability by adding Built-In Test. The gain, noise figure, difference of amplitude and phase on the signal path is respectively 20${\pm}$2[dB], 19[dB], ${\pm}$2[dB], $10^{\circ}$ and below.