• Tribology and Lubricants
• /
• v.34 no.4
• /
• pp.146-159
• /
• 2018

This paper presents a wear analysis procedure for calculating the wear of journal bearings of a four-strokes and four-cylinder engine operating at a constant angular crank shaft speed during firing conditions. To decide whether the lubrication state of a journal bearing is in the possible region of wear scar, we utilize the concept of the centerline average surface roughness to define the most oil film thickness scarring wear (MOFTSW) on two rough surfaces. The wear volume is calculated from the wear depth and wear angle, determined by the magnitude of each film thickness on a set of oil films with thicknesses lower than the MOFTSW at every crank angle. To calculate the wear volume at one contact, the wear range ratio during one cycle is used. The total wear volume is then determined by accumulating the wear volume at every contact. The fractional film defect coefficient, asperity load sharing factor, and modified specific wear rate for the application of the mixed-elasto-hydrodynamic lubrication regime are used. The results of this study show that wear occurs only at the connecting-rod big-end bearing. Thus, simulation results of only the big-end bearing are illustrated and analyzed. It is shown that the wear volume of each wear scar group occurs consecutively as the crank angle changes, resulting in the total accumulated wear volume.

• Nuclear Engineering and Technology
• /
• v.25 no.1
• /
• pp.166-177
• /
• 1993

A simplified thermal analysis method to evaluate the maximum temperature of the CANDU 37-element fuel bundle within a fuel basket in a given spent fuel dry storage canister has been presented along with the results of sample analyses performed to examine the parametric effects of the ambient conditions on the maximum fuel temperature within a canister. To solve the multi-dimensional heat transfer problem of the complex geometry of rod bundles within a canister where three modes of heat transfer are superimposed, the CANDU spent fuel bundles stored in the dry storage canister are first replaced by equivalent concentric fuel cylinders. The simplified axi-symmetric two-dimensional multi-mode heat transfer problem of the equivalent fuel cylinders is then analyzed with an existing computer code, HEATING5, using additional input data and heat transfer correlations. A comparison between the predicted temperature profile and the mock-up test results shows that the agreement is quite satisfactory.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.5 s.66
• /
• pp.16-25
• /
• 2005

The effect of vertical riser support system on the dynamic behaviour of a classical spar platform is investigated. Spar platform generally uses buoyancy-can riser support system, but as water depth gets deeper the alternative riser support system is required due to safety and cost issues. The alternative riser support system is to hang risers off the spar platform using pneumatic cylinders rather than the buoyancy-can. The existing numerical model for hull/mooring/riser coupled dynamics analysis treats riser as an elastic rod truncated at the keel (truncated riser model), thus, in this model, the effect of riser support system can not be modeled correctly. Due to this reason, the truncated riser model tends to overestimate the spar pitch and heave motion. To evaluate more realistic global spar motion, mechanical coupling among risers, guide frames and support cylinders inside of spar moon-pool should be modeled. In the newly developed model, the risers are extended through the moon-pool by using nonlinear finite element methods with realistic boundary condition at multiple guide frames. In the simulation, the vertical tension from pneumatic cylinders is modeled by using ideal-gas equation and the vertical tension from buoyancy-cans is modeled as constant top tension. The different dynamic characteristics between buoyancy-can riser support system and pneumatic riser support system are extensively studied. The alternative riser support system tends to increase spar heave motion and needs damper system to reduce the spar heave motion.

• Publications of The Korean Astronomical Society
• /
• v.36 no.3
• /
• pp.65-78
• /
• 2021

Jagyeokru, an automatic striking water clock described in the Sejong Sillok (Veritable Records of King Sejong) is essentially composed of a water quantity control device and a time-signal device, with the former controlling the amount or the flow rate of water and the latter automatically informing the time based on the former. What connects these two parts is a signal generating device or a power transmission device called the 'Jujeon' system, which includes a copper rod on the float and ball-racked scheduled plates. The copper products excavated under Gongpyeong-dong in Seoul include a lot of broken plate pieces and cylinder-like devices. If some plate pieces are put together, a large square plate with circular holes located in a zigzag can be completed, and at the upper right of it is carved 'the first scheduled plate (一箭).' Cylinder-like devices generally 3.8 cm in diameter are able to release a ball, and have a ginkgo leaf-like screen fixed on the inner axis and a bird-shaped hook of which the leg fixes another axis and the beak attaches to the leaf side. The lateral view of this cylinder-like device appears like a trapezoid and mounts an iron ball. The function of releasing a ball agrees with the description of Borugak Pavilion, where Jagyeokru was installed, written by Kim Don (1385 ~ 1440). The other accounts of Borugak Pavilion's and Heumgyeonggak Pavilion's water clocks describe these copper plates and ball releasing devices as the 'Jujeon' system. According to the description of Borugak Pavilion, a square wooden column has copper plates on the left and right sides the same height as the column, and the left copper plate has 12 drilled holes to keep the time of a 12 double-hours. Meanwhile, the right plate has 25 holes which represent seasonal night 5-hours (Kyeong) and their 5-subhours (Jeom), not 12 hours. There are 11 scheduled plates for seasonal night 5-hours made with copper, which are made to be attached or detached as the season. In accordance with Nujutongui (manual for the operation of the yardstick for the clepsydra), the first scheduled plate for the night is used from the winter solstice (冬至) to 2 days after Daehan (大寒), and from 4 days before Soseol (小雪) to a day before the winter solstice. Besides the first scheduled plate, we confirm discovering a third scheduled plate and a sixth scheduled plate among the excavated copper materials based on the spacing between holes. On the other hand, the width of the scheduled plate is different for these artifacts, measured as 144 mm compared to the description of the Borugak Pavilion, which is recorded as 51 mm. From this perspective, they may be the scheduled plates for the Heumgyeonggak Ongru made in 1438 (or 1554) or for the new Fortress Pavilion installed in Changdeokgung palace completed in 1536 (the 31^st year of the reign of King Jungjong) in the early Joseon dynasty. This study presents the concept of the scheduled plates described in the literature, including their new operating mechanism. In addition, a detailed model of 11 scheduled plates is designed from the records and on the excavated relics. It is expected that this study will aid in efforts to restore and reconstruct the automatic water clocks of the early Joseon dynasty.

• 대한공업교육학회지
• /
• v.32 no.2
• /
• pp.87-103
• /
• 2007

The purpose of this study was to develop of the smoke flow visualization device of learning wind tunnel, teaching-learning materials in order to demonstrate air-flow around the fluid-flow field qualitatively and understand the resistance concepts of fluid-flow in secondary school. The contents of this study were consisted of the development and experiment of smoke flow visualization for learning wind tunnel. The main results of this study were as follows: First, this developed teaching-learning material here will help students understand the fundamental physical phenomena related with the resistance of fluid and the various patterns of air-flow in the field of transportation technology. Second, flow visualization has shown the same tendency in both of theoretical and experimental patterns. Third, the airfoil model has the smallest wake region meaning resistance against air-flow of circular cylinder and square rod model. Forth, flow separation point at leading edge and wide wake region began to show under the angle of attack of airfoil model ${\alpha}$ is $20^{\circ}$. Fifth, the wake width of the flow field behind a golf ball with dimple became slightly narrower than that without dimple. Sixth, the developed device was made to apply the teaching and learning materials for the experiment and practice in order to increase students' interest and attitude.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.2
• /
• pp.98-106
• /
• 2003

Nondestructive test (NDT) provides much information on concrete without damage of structural functions. Of NDT methods, elastic wave propagation methods, such as ultrasonic pulse velocity (UPV) method and impact-echo (IE) method, have been successfully used to estimate the strength, elastic modulus, and Poisson's ratio of concrete as well as to detect the internal microstructural change and defects. In this study, the concretes with water-binder ratio ranging from 0.27 to 0.50 and fly ash content of 20% were made and then their longitudinal wave velocities were measured by UPV and IE method, respectively. Test results showed that the UPV is greater than the longitudinal wave velocity measured by the If method, i.e., rod-wave velocity obtained from the same concrete cylinder. It was found that the difference between the two types of velocities decreased with increasing the ages of concrete and strength level. Moreover, for the empirical formula, the dynamic Poisson's ratio, static and dynamic moduli of elasticity, and velocity-strength relationship were determined. It was observed that the Poisson's ratio and the modulus of elasticity determined by the dynamic method are greater than those determined by the static test. Consequently, for the more accurate estimation of concrete properties using the elastic wave velocities, the characteristics of these velocities should be understood.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.282-288
• /
• 2002

본 연구는 상업용 규모의 쇄미선별공정에 사용할 수 있는 파이로트 규모 원통형 홈 선별기 시작기의 설계 및 제작에 필요한 기초 연구로서, 실험실용 원통형 홈 선별기를 이용하여 쇄미선별 실험을 실시하였다. 원통 회전속도, trough각도, indent 크기와 형상, 공급량을 요인으로 하여 완전립의 수거율과 순도, 쇄립의 수거율과 순도 및 선별효율을 조사하였다. 수행한 연구결과를 요약하면 다음과 같다. 1. 선별효율에 대한 원통 회전속도와 trough각도의 단독효과 및 교호작용은 1% 수준에서 유의성이 인정되었다. 원통 회전속도가 커지면trough각도 역시 그에 따라 적절히 증가시켜야만 선별효율의 저하가 방지되는 것으로 나타났다. 2. 최고 선별효율 값은 홈의 모양과 크기, 그리고 공급량에 관계없이 낮은 회전속도 (17rpm)와 중간 trough각도 (37.5$^{\circ}$또는 60$^{\circ}$)가 조합된 처리에서 나타났으며, 60~70% 범위의 높은 값을 보였다. 선별효율에 관한 원통 회전속도와 trough각도의 최적 조합은 17rpm, 37.5$^{\circ}$라고 판단된다. 3. 말발굽형 홈과 반구형 홈 간 선별효율의 차이는 없었다. 따라서, 실제 상업용 규모의 원통형 홈 쇄미선별기 개발에 있어서는 제작이 쉽고 유지.보수가 간편한 반구형 홈을 채택하는 것이 바람직할 것으로 생각된다. 길이 2.5mm이하의 미립인 쇄미의 선별에 사용할 홈의 크기는 2.5mm 보다는 약간 큰 3.0mm 정도가 되어야만 할 것으로 판단된다. 4. 공급량에 따른 선별효율의 차이는 1% 수준에서 유의성이 인정되었으며, 공급량이 작았을 때 전반적으로 선별효율이 높았다.타리 시프터를 채택, 사용하고 있었으며, 로타리시프터 사용상의 문제는 회전몸체를 지지하는 rod spring의 파손 등 구조와 관련된 것이었다. 로타리 시프터에 의한 쇄립의 선별과 제거정도는 만족할 만한 수준은 아니었다. 4. 국내 유통백미 완전립의 길이, 폭, 두께는 각각 5.02mm, 2.93mm, 2.03mm이었으며, 산물밀도와 천립중은 각각 745.3kg/m3 및 20.46g이었다. 5. RPC 백미제품의 품질경쟁력 향상을 유도하고자 현행 쇄미의 정의와 기준을 보다 강화하여 다음과 같은 쇄미 기준과 계급을 설정, 제시하였다. "완전립" - 길이가 3.75mm이상인 미립 "준완전립" - 길이가 2.5∼3.75mm인 미립 "쇄미" - 길이가 1.75∼2.5 mm인 미립 "이물" - 길이가 1.75mm이하인 미립.볼 때 상토 종자혼합비 6 : 1, 성형롤 회전속도 약 7 rpm으로 판단되며, 이 때 제조능력은 시간당 약 65 Kg(펠렛종자 약 39,000 개), 성형률 약 87 %, 종자손실률은 약 30 %, 펠렛종자 내 평균 종자수는 약 5.5 개, 완전 벼 종자 3개 이상 포함 펠렛종자 비율은 약 100 %가 될 것으로 보인다. 세포의 Androgen 생성을 촉진시키는 역할이 있는 것으로 보여진다 따라서 옻나무 유래 F는 포유동물의 생식기능에 중요하게 작용하는 것으로 사료된다.된다.정량 분석한 결과이다. 시편의 조성은 33.6 at% U, 66.4 at% O의 결과를 얻었다. 산화물 핵연료의 표면 관찰 및 정량 분석 시험시 시편 표면을 전도성 물질로 증착시키지 않고, Silver Paint 에 시편을 접착하는 방법으로도 만족한 시험 결과를 얻을 수 있었다.째, 회복기 중에 일어나는 입자들의 유입은 자기폭풍의 지속시간