• 한국해양공학회지
• /
• 제6권1호
• /
• pp.78-86
• /
• 1992

The creep behaviors of 1%Cr-Mo-V and 12%Cr steam turbine rotor steels under static or cyclic load were examined at 600 and $700^{\circ}C$. The relationship between these two kinds of phenomena was studied and the experimental results were summarized as follows: 1) It is confirmed that the cyclic creep strain dependent on time is more available for creep, behavior analysis according to frequency change than that dependent on number of cycles, and the static creep, the special case of cyclic creep with stress ratio of 1 can be also more effectively analyzed by time-dependence. 2) The steady cyclic creep rate vs. the steady static creep rate, increases according to the increase of stress ratio, and this phenomena may occur on occasion of the decrease of the internal stress. 3) The initial strain affects on all the creep properties of the transient region, the steady state region and the rupture time in cyclic creep as well as static creep, and the quantitative relationships among them exist.

• 한국안전학회지
• /
• 제15권4호
• /
• pp.35-40
• /
• 2000

The influence of cyclic loading history on the creep behavior of the 30 vol% hot-pressed $SiC_f/Si_3N_4copmposite was experimentally investigated at $1200^{\circ}C$. The duration of loading/unloading had great effects on the creep behaviors. The short term duration cyclic loading history test results showed significant reduction in the primary and steady-state creep rates. For example, 300sec loading/300sec unloading history resulted in 70% lower steady-state creep rate than that of the continuous loading. However the long term duration cyclic loading history test results showed little change in creep rates compared to those of the continuous one. The reason for the significant change in the short term duration cycles was estimated due to the change in the stress redistribution between the fiber and matrix during the creep recovery in the primary stage.

• 대한화학회지
• /
• 제51권4호
• /
• pp.305-311
• /
• 2007

정류상태(steady state)와 과도상태(transient state)의 Tafel 기울기, 순환 전압-전류 곡선, 임피던스 측정자료에 기초하여 인공해수에서 구리의 부식과 부동화에 대한 반응 메커니즘을 제안하였다. 구리의 산화환원 반응은 인공해수에서의 산소농도와 전극전위에 의존함을 알 수 있었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.252-257
• /
• 2000

An efficient method is developed for mold thermal cycle analysis in repeated forming process, which is well suited to the analysis in TV glass production. plunger, which is a mold to press-form the glass, undergoes temperature fluctuation during a cycle due to the repeated contact and separation from the glass, which attains a cyclic steady state in the end. If analyzed straightforwardly of this problem, it leads to more than 80 cycles to get reasonable solution, and it is yet hard to setup stopping creteria due to extremely slow convergence. An exponential fitting method is proposed to solve the problem, where an exponential function is found to best approximate temperature values of 3 consecutive cycles, and new cycle is restarted with the function value at infinite time. From numerical implementation, it is found that the method reduces the number of cycles dramatically to only $6{\sim}15$ cycles to reach accurate solution within $1^{\circ}$ error. A system for the analysis is contructed, in which the thermal analysis is performed by commercial software ANSYS, and the fitting of the result is done by IMSL library.

• 열처리공학회지
• /
• 제18권3호
• /
• pp.177-182
• /
• 2005

The steady state cyclic mechanism, and the behaviour of Nicoseal(Fe-29Ni-17Co) have been examined under the condition of square wave stress cyclic tension creep test at the temperature, stress and frequency range of $430{\sim}470^{\circ}C$($0.41{\sim}0.43T_m$), 353~383 MPa, and 3 cpm, respectively. Also, the relationship between cyclic creep and static creep have been examined. The stress exponents(n) for the static creep deformation of this alloy were 11.6, 10.0, 8.4 and 7.9 at the temperature of 430, 445, 460 and $470^{\circ}C$, respectively. The apparent activation energies (Q) for the static creep deformation were 54.2, 51.8, 49.7 and 46.8 kcal/mole for the stress of 353, 363, 373 and 383 MPa, From the above results, it could be considered that the cyclic creep accelaration phenomena was obtained and that the cyclic deformation for Nicoseal seemed to be controlled by dislocation climb over the range of experimental conditions. Nicoseal alloy under the cyclic creep conditions was obtained as P=(T+460)(logt+17). The failure plane observed by SEM showed up transgranular fracture at all range.

• International Journal of Fluid Machinery and Systems
• /
• 제4권1호
• /
• pp.161-171
• /
• 2011

The availability of a high quality open source CFD simulation platform like OpenFOAM offers new R&D opportunities by providing direct access to models and solver implementation details. Efforts have been made by Hydro-Qu$\'{e}$bec to adapt OpenFOAM to hydroturbines for the development of steady-state capabilities. This paper describes the developments that have been made to implement new turbomachinery related capabilities: multiple frames of reference solver, domain coupling interfaces (GGI, cyclicGGI and mixing plane) and specialized boundary conditions. Practical use of the new turbomachinery capabilities are demonstrated for the analysis of a 195-MW Francis turbine.

• Steel and Composite Structures
• /
• 제21권4호
• /
• pp.703-753
• /
• 2016

The ratcheting behavior was studied experimentally for Z2CND18.12N elbow piping under cyclic bending and steady internal pressure. Dozens of cyclic plasticity models for structural ratcheting responses simulations were used in the paper. The four models, namely, Bilinear (BKH), Multilinear (MKIN/KINH), Chaboche (CH3), were already available in the ANSYS finite element package. Advanced cyclic plasticity models, such as, modified Chaboche (CH4), Ohno-Wang, modified Ohno-Wang, Abdel Karim-Ohno and modified Abdel Karim-Ohno, were implemented into ANSYS for simulating the experimental responses. Results from the experimental and simulation studies were presented in order to demonstrate the state of structural ratcheting response simulation by these models. None of the models evaluated perform satisfactorily in simulating circumferential strain ratcheting response. Further, improvement in cyclic plasticity modeling and incorporation of material and structural features, like time-dependent, temperature-dependent, non-proportional, dynamic strain aging, residual stresses and anisotropy of materials in the analysis would be essential for advancement of low-cycle fatigue simulations of structures.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.194-199
• /
• 2000

The creep rate is affected by the temperature and in fact. if the temperature above $T_M/2(T_M:melting\;point)$. The aim of the present investigation is to study the relationship of static creep and cyclic creep behavior of pure copper and the formulation of these phenomena with the special attention to the instantaneous strain. strain rate from time and number of cycles have the same inclination Steady state creep rate depend upon maximum stress and can be expressed as linear function according to Power law creep equations Creep rupture time has relation with creep rate. and it make a group represented as the same direct line regardless of max stress, stress ratio and the temperature. Initial strain effect on continuous creep deformation. and have guantitative relationship between elastic and Plastic strain. LMP have similar tendency than OSDP and MHP according to temperature

• Computers and Concrete
• /
• 제8권3호
• /
• pp.343-355
• /
• 2011

This paper presented the model to predict the chloride diffusion coefficient in tension zone of plain concrete under flexural cyclic load. The fictitious crack based analytical model was used together with the stress degradation law in cracked zone to predict crack growth of plain concrete beams under flexural cyclic load. Then, under cyclic load, the chloride diffusion, in the steady state and one dimensional regime, through the tension zone of the plain concrete beam, in which microcracks were formed by a large number of cycles, was simulated with assumptions of continuously straight crack and uniform-size crack. The numerical analysis in terms of the chloride diffusion coefficient, $D_{tot}$, normalized $D_{tot}$, crack width and crack length was issued as a function of the load cycle, N, and load level, SR. The nonlinear model as regarding with the chloride diffusion coefficient in tension zone and the load level was proposed. According to this model, the chloride diffusion increases with increasing load level. The predictions using model fit well with experimental data when we adopted suitable crack density and tortuosity parameter.

• 대한기계학회논문집B
• /
• 제24권9호
• /
• pp.1219-1226
• /
• 2000

An efficient method is developed for plunger thermal cycle analysis in repeated forming process of the TV glass. The plunger undergoes temperature fluctuation during a cycle due to the repeated contact and separation from the glass, which attains a cyclic steady state having same temperature history at every cycle. Straightforward analysis of this problem brings about more than 80 cycles to get reasonable solution, and yet hard to setup stopping criteria due to extremely slow convergence. An exponential fitting method is proposed to overcome the difficulty, which finds exponential function to best approximate temperature values of 3 consecutive cycles, and new cycle is restarted with the fitted value at infinite time. Numerical implementation shows that it reduces the number of cycles dramatically to only 6-18 cycles to reach convergence within 10 accuracy. A system for the analysis is constructed, in which the thermal analysis is performed by commercial software ANSYS, and the fitting of the result is done by IMSL library. From the parametric studies, one reveals some important facts that although the plunger cooling or the glass thickness is increased, its counter part in contact is not much affected, duo to the low thermal conductance of the glass.