• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.2
• /
• pp.221-229
• /
• 1996

The engine speed fluctuation at idle operation mainly comes from cyclic variation of combustion in SI engine. In the present study, engineering model that is representing the cyclic variation of combustion was proposed for the sub-model of the engine cycle simulation. From the observed behaviors of the mass burn rates, probability density functions for the parameters of Wiebe function were defined. The mass burn rate of each cycle is obtained by Monte Cralo perturbation method with the probability function. The simulation results shows that trends of cylinder pressure variation and imep distribution follow up with those of experimental results at idle condition.

• The Korean Journal of Ceramics
• /
• v.7 no.2
• /
• pp.63-69
• /
• 2001

We investigated strength degradations from cyclic contact fatigue in self-toughened glass-ceramics. Hertzian indentation was used to induce cyclic contact load. Dynamic fatigue was also performed with changing stress rates from 0.01 to 10000 MPa/sec. After that, strength data and fracture origins were analysed. As the number of contact cycles increased or stressing rate decreased, severe strength degradation occurred by as much as 50% because of radial cracks developed from microcrack coalescence.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.12
• /
• pp.44-55
• /
• 1994

This study is to apply the theory of fatigue fracture to solder joints under thermal cyclic loading and predict life of solder joint to failure. A 62Sn-36Pb-2Ag solder was used in this study. Tensile tests were preformed at temperatures of 15.dec. C, 50.dec. C and 85.dec. C in order to find terms of crack length "a". plastic strain range ""${\Delta}{\varepsilon}_p$" and temperature "T". Solder joint under thermal cyclic loading was analyzed by FEM. this FEM analysis together with the crack growth rate will provide the capability of the fatigue life prediction of solder joints and enhance the reliability od solder joint.

• Journal of Electrochemical Science and Technology
• /
• v.11 no.2
• /
• pp.140-147
• /
• 2020

This paper presents a hypothesis and its experimental validation that ∆E (E_sec,corr - E_corr) of cyclic polarization curve of an Al-Zn-Mg-Cu alloy decreases firstly and then increases with the increasing of corrosion rate or corroded fraction F_corr of alloy surface. The minimum value of ∆E is obtained when F_corr ≈ 50%. In addition, a proportional relationship between ∆E and |50% - F_corr| was found. This non-monotonic relation between ∆E and extent of localized corrosion indicates that additional attention should be paid on using ∆E to assess localized corrosion behaviour of Al-Zn-Mg-Cu alloys.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.5
• /
• pp.213-217
• /
• 2012

Carbon coils could be synthesized on nickel catalyst layer-deposited silicon oxide substrate using $C_2H_2$ and $H_2$ as source gases under thermal chemical vapor deposition system. By the incorporation of $SF_6$ additive in cyclic modulation manner, the dominant formation of the nanosized carbon coils could be achieved with maintaining the minimized sulfur additive amount. The geometry variation of the as-grown carbon coils, such as linear type, microsized coil type, wavelike nanosized coil type, and nanosized coil type, were investigated according to the different cyclic modulation manner of $SF_6$ flow. $SF_6$ gas incorporation develops the coil-type geometry. Furthermore, the higher flow rate of $SF_6$ gas increased the amount of the nanosized carbon coils. The slightly increased etching ability by $SF_6$ addition seems to be the cause for these results.

• Asian-Australasian Journal of Animal Sciences
• /
• v.17 no.5
• /
• pp.608-611
• /
• 2004

The 15 buffaloes were divided into three groups, viz. group 1: normal cyclic buffaloes; group 2: postpartum anoestrus buffaloes and group 3: post partum anoestrus buffaloes supplemented with intramuscular injections of Vit. E.-care Se containing 500 mg $\alpha$-tocopheryl acetate and 15 mg selenium at weekly intervals for two months. The postpartum anoestrus buffaloes had significantly higher levels of erythrocytic lipid peroxidation, superoxide dismutase and glucose-6 phosphate dehydrogenase activities but lower glutathione peroxidase activity as compared to normal cyclic buffaloes. The supplementation of vitamin E and selenium lowered the level of erythrocytic lipid peroxidation, superoxide dismutase and glucose-6 phosphate dehydrogenase activities but it had no effect on whole blood selenium and erythrocytic gluathione peroxidase activity. All the animals in group 3 became cyclic and showed 60% conception rate.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.12
• /
• pp.1745-1747
• /
• 2016

In this paper, we propose a construction method of irregular quasi-cyclic low-density parity-check codes based on perfect difference families with various block sizes. The proposed codes have advantages in that they support various values with respect to code rate, length, and degree distribution. Also, this construction enables very short lengths which are usually difficult to be achieved by a random construction. We verify via simulations the error-correcting performance of the proposed codes.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.3
• /
• pp.107-110
• /
• 2006

We fabricated the monolayers onto QCM by self-assembly using viologen, which has been widely used as electron acceptor. A gold electrode of the QCM was cleaned by piranha solution and prepared the ethanol-acetonitrile(1:1) solution with 2 m mol/l viololgen compounding of pure hi gas. We determined the time dependence to resonant frequency shift during self-assembly process and the electrochemical behavior of the self-assembled viologen monolayers by cyclic voltammetry. With increasing scan rate, the redox peak current of the viologen increased linearly. This was signified that the redox reaction was reversible. The EQCM measurements revealed the anions transfer during redox reactions, respectively. From the EQCM data, the well-defined shape peaks were nearly equal charges by cyclic voltammetry.

• Journal of Korea Society of Industrial Information Systems
• /
• v.1 no.1
• /
• pp.29-62
• /
• 1996

In this paper, the problem of determining cyclic schedules for a material handling hoist in the printed-circuit-board(PCB) electroplating line is considered. The objective of this research is to determine an optimal simple-cycle schedule of the hoist which in turn maximizes the line throughput rate. Previous approaches to the cyclic hoist scheduling problem are all mathematical programming-based approaches to develop cyclic schedules(Mixed Integer Programming, Linear Programming based Branch and Bound, Branch and Bound Search Method and so on). In this paper, a genetic algorithm-based approach for a single hoist scheduling in the PCB electroplating line is described. Through some experiments for the well known example data and randomly generated data, the proposed algorithm is shown to be more efficient than the previous mathematical programming-based algorithm.

• Journal of the Korean Applied Science and Technology
• /
• v.27 no.4
• /
• pp.531-538
• /
• 2010

The electrochemistry characterization of metal is important in many industrial applications. In this study, we investigated the C-V diagrams related to the electrochemistry characterization of nickel. We determined electrochemical measurement by using cyclic voltammetry with a three electrode system. A measuring range was reduced from initial potential to -1350mV, continuously oxidized to 1650mV and measured to the initial point. The scan rate were 100, 150, 200 and 200mV/s. As a result, the C-V characterization of nickel using ethanolamine and ethylethanolamine inhibitor appeared irreversible process caused by the oxidation current from the cyclic voltammogram. After adding ethanolamine compound additive, adsorption film constituted, and the passive phenomena happened. According to the results by cyclic voltammetry method, it was revealed that the effect of the electrochemistry characterization of nickel depends on ethanolamine structure interaction to adsorption complex.