• Journal of Advanced Marine Engineering and Technology
• /
• 제33권8호
• /
• pp.1100-1106
• /
• 2009

최근, 디젤기관의 고효율달성을 위한 방법으로 밀러방식의 고팽창사이클에 대한 연구가 관심이 높다. 본 연구에서는 고팽창 디젤사이클을 구성하여 열역학적으로 해석하고, 몇몇 인자에 의한 사이클 특성을 분석하였다. 이론해석 결과 흡기밸브 닫힘시기가 지각될수록 유효압축비의 감소로 상대적인 팽창비의 효과는 커져 팽창-압축비의 비는 기대할 수 있었으나, 압축압력 및 흡입공기의 역류로 인해 평균유효 압력과 출력의 감고를 수반하였다. 따라서 이에 대한 대책이 있어야 진정한 의미의 고팽창 디젤사이클이 실현되고 열효율향상 가능성이 있음이 확인되었다. 위와 같은 사이클을 실제기관으로부터 구현하기 위해 흡기밸브 닫힘시기를 늦게 하는 제어시스템을 구축하고, 시험을 위해서 S/B가 약 3인 저속 단기통 디젤기관에 가변밸브타이밍(VVT)시스템을 적용하여 성능을 평가하였다. 그 결과 시험기관의 밸브제어에는 큰 문제없는 것으로 평가되었다.

• 오토저널
• /
• 제13권2호
• /
• pp.67-87
• /
• 1991

The computer program which predicts the gas exchange process of multi-cylinder 4-Stroke cycle spark-ignition engine, can be great assistance for the design and development of new engine. In this study, the computer program was developed to predict the gas exchange process of multi-cylinder four stroke cycle spark ignition engine including intake and exhaust systems. When gas exchange process is to be calculated, the evaluation of the variation of the thermo-dynamic properties with time and position in the intake and exhaust systems is required. For the purpose, the application of the generalized method of characteristics to the gas exchange process is known as one of the method. The simulation model developed was investigated to the analysis of the branch system of multi-cylinder. The models used were the 2-zone expansion model and single zone model for in cylinder calculation and the generalized method of characteristic including area change, friction, heat transfer and entropy gradients for pipe flow calculation. The empirical constants reduced to least number as possible were determined through the comparison with the experimented indicator diagram of one particular operation condition and these constants were applied to other operating condition. The predicted pressures in cylinder were compared with the experimental results over the wide range of equivalence ratio and ignition timing. The predicted values have shown good agreement with the experimental results. The thermodynamic properties in the intake and exhaust system were predicted over the wide range of equivalence ratio and ignition timing. The obtained results can be summarized as follows. 1. Pressures in the exhaust manifold have a little influence on the equivalence ratio, a great influence on the ignition timing. 2. Pressures in the inlet manifold are nearly unchanged by the equivalence ratio and the ignition timing. 3. In this study, the behaviors of the exhaust temperature, gas in the exhaust manifold were ascertained.

• 한국해양공학회지
• /
• 제4권2호
• /
• pp.250-250
• /
• 1990

In this paper, fatigue tests were carried out at stress test levels of 461 MPa, 441 MPa, and 431 MPa by using smooth specimen of$2_{1/4}$ Cr-1 Mo steel with the stress ratio(R) of 0.05. The initiation, growth and coalescense process of the major cracks and sub-cracks among the fatigue cracks on the smooth specimen are investigated and measured under each stress level at a constant cycle ratio by the replica technique with optical microscope. Some of the important results are as follows: In spite of the difference of stress levels, the major crack data gather into a small band in the curve of surface crack length and crack depth against cycle ratio N/Nf. The sub-crack data, however, deviate from the band of the major crack. The growth rates, da/dN, of major and sub-crack plotted against the stress intensity factor range, ${\Delta}K$, have the tendency to be compressed on a relatively small band. But it is more effective to predict fatigue life through major cracks. The propagation behavior of surface microcracks on the smooth specimens coincides with that of the specimen having an artificial small surface defect or through crack.

• 한국수소및신에너지학회논문집
• /
• 제19권5호
• /
• pp.386-393
• /
• 2008

The Sulfur-iodine(SI) thermochemical cycle is one of the most promising methods for massive hydrogen production. For the purpose of continuous operation of SI cycle, phase separation characteristics into two liquid phases ($H_2SO_4$-rich phase and $HI_x$-rich phase) were directly investigated via Bunsen reaction. The experiments for Bunsen reaction were carried out in the temperature range, from 298 to 333 K, and in the $I_2/H_2O$ molar ratio of $0.109{\sim}0.297$ under a continuous flow of $SO_2$ gas. As the results, solubility of $SO_2$, decreased with increasing the temperature, had considerable influence on the global composition in the Bunsen reaction system. The amounts of impurity in each phase(HI and $I_2$ in $H_2SO_4$-rich phase and $H_2SO_4$ in $HI_x$-rich phase) were decreased with increasing $H_2SO_4$ molar ratio and temperature. To control the amounts of impurity in $HI_x$-rich phase, temperature is a factor more important than $I_2/H2_O$ molar ratio. On the other hand, the affinity between $HI_x$ and $H_2O$ was increased with increasing $I_2/H2_O$molar ratio.

• 한국전문물리치료학회지
• /
• 제13권2호
• /
• pp.61-69
• /
• 2006

The purpose of this study was to compare the electromyography (EMG) activities of the lumbar extensor muscles during motion of trunk flexion-extension and compare range of motion (ROM) with a 3-dimensional motion analysis system of the lumbar region between subjects with chronic low back pain (CLBP) and healthy subjects during the trunk flexion-extension, trunk rotation and trunk lateral flexion cycle. Thirty CLBP subjects and thirty healthy subjects were included. We measured the root mean square (RMS) value of the lumbar extensor muscles from resting, standing, lumbar flexion and return position. The RMS ratio was normalized from maximal EMG activity of the lumbar extensor muscles during trunk motion. The results of this study showed that the RMS ratio of the lumbar extensor was significantly higher in CLBP subjects than healthy subjects during all of trunk motion (p<.05). The ratio of the highest RMS value during flexion and extension was higher in CLBP subjects than in healthy subjects (p<.05). The ROM of the lumbar region was significantly lower in CLBP subjects than healthy subjects during trunk flexion-extension, trunk rotation and lateral flexion cycle. The relationship between the RMS ratio for full lumbar flexion and the ROM of lumbar flexion was not correlated significantly. CLBP subjects have both decreased ROM of the lumbar region and higher muscle activities of the lumbar extensor muscle than healthy subjects.

• Journal of Power Electronics
• /
• 제11권2호
• /
• pp.156-162
• /
• 2011

The control loop time delay caused by sampling, the zero-order-holder effect and calculations is inevitable in the digital control of dc-dc switching converters. The time delay will limit the bandwidth of the control loop and therefore degrade the transient performance of digital systems. In this paper, the quantization time delay effects with different time delay values based on a generic second-order system are analyzed. The conclusion that the bandwidth of digital control is reduced by about 20% with a one cycle delay and by 50% with two cycles of delay in comparison with no time delay is obtained. To compensate the time delay and to increase the control loop bandwidth, a duty ratio predictive control scheme based on linear extrapolation is proposed. The compensation effect and a comparison of the load variation transient response characteristics with analogy control, conventional digital control and duty ratio predictive control with different time delay values are performed on a point-of-load Buck converter by simulations and experiments. It is shown that, using the proposed technique, the control loop bandwidth can be increased by 50% for a one cycle delay and 48.2% for two cycles of delay when compared to conventional digital control. Simulations and experimental results prove the validity of the conclusion of the quantization effects of the time delay and the proposed control scheme.

• 한국수소및신에너지학회논문집
• /
• 제7권2호
• /
• pp.165-171
• /
• 1996

The effect of rolling on the charge-discharge property was studied for metal hydride negative electrode. $(LM)Ni_{3.6}Al_{0.4}Co_{0.7}Mn_{0.3}$(pleateau pressure : below 1 atm at room temperature, volume expansion : 9%, entalpy : $8.7kcal/molH_2$) alloy was prepared by arc melting, and then it was coated with various copper weight percent. The copper coated alloys were then rolled with the different reduction ratio. From the results, it was found that the maximum discharge capacity increased with increasing reduction ratio, and 15wt% copper coated sample shows the highest discharge capacity, 324mAh/g, after rolling with 30% reduction ratio. In view of cycle life for the negative electrode, the 15wt% copper coated electrode which was rolled with 13% reduction ratio showed the longest cycle life compared with other electrodes.

• 지질공학
• /
• 제26권4호
• /
• pp.485-495
• /
• 2016

본 연구에서는 방파제 하부지반을 저치환율 재료로 보강 및 개량하기 위한 치환율과 재하중 방치기간을 확률론적 최적화 기법을 이용하여 분석하였다. 해석에 필요한 확률변수의 불확실성을 최소화하기 위하여 사전자료를 활용한 베이지안 갱신결과 최대 39.8% 포인트까지 불확실성이 감소하였고, 특히 사전함수의 표본수가 더 많은 구간의 감소폭이 컸다. 치환율 결정을 위하여 저치환율 단면 중 15~40% 범위에서 일계신뢰도법 및 몬테카를로 시뮬레이션 방법에 의해 해석한 결과 목표파괴확률을 만족하는 치환율은 심층고결처리 및 쇄석다짐말뚝 구간에서 각각 20% 및 25% 이상으로 나타났다. 치환율에 대한 최적화를 위하여 생애주기비용 분석을 실시한 결과 목표파괴확률을 만족하는 범위 내에서 최적 치환율이 산정되었으며, 두 구간에서 각각 20% 및 30%가 가장 경제적인 것으로 결정되었다. 재하중의 방치기간에 대한 확률론적 해석결과 3개월 이상인 경우 모두 목표파괴확률을 만족하는 것으로 나타났다.

• Nuclear Engineering and Technology
• /
• 제37권1호
• /
• pp.91-100
• /
• 2005

Kyung-hee Thorium Fuel (KTF), a heterogeneous thorium-based seed and blanket design concept for pressurized light water reactors, is being studied as an alternative to enhance proliferation resistance and fuel cycle economics of PWRs. The proliferation resistance characteristics of the KTF assembly design were evaluated through parametric studies using neutronic performance indices such as Bare Critical Mass (BCM), Spontaneous Neutron Source rate (SNS), Thermal Generation rate (TG), and Radio-Toxicity. Also, Fissile Economic Index (FEI), a new index for gauging fuel cycle economy, was suggested and applied to optimize the KTF design. A core loaded with optimized KTF assemblies with a seed-to-blanket ratio of 1: 1 was tested at the Korea Next Generation Reactor (KNGR), ARP-1400. Core design characteristics for cycle length, power distribution, and power peaking were evaluated by HELIOS and MASTER code systems for nine reload cycles. The core calculation results show that the KTF assembly design has nearly the same neutronic performance as those of a conventional $UO_2$ fuel assembly. However, the power peaking factor is relatively higher than that of conventional PWRs as the maximum Fq is 2.69 at the M$9^{th}$ equilibrium cycle while the design limit is 2.58. In order to assess the economic potential of a heterogeneous thorium fuel core, the front-end fuel cycle costs as well as the spent fuel disposal costs were compared with those of a reference PWR fueled with $UO_2$. In the case of comprising back-end fuel cycle cost, the fuel cycle cost of APR-1400 with a KTF assembly is 4.99 mills/KWe-yr, which is lower than that (5.23 mills/KWe-yr) of a conventional PWR. Proliferation resistance potential, BCM, SNS, and TG of a heterogeneous thorium-fueled core are much higher than those of the $UO_2$ core. The once-through fuel cycle application of heterogeneous thorium fuel assemblies demonstrated good competitiveness relative to $UO_2$ in terms of economics.

• 대한기계학회논문집
• /
• 제18권3호
• /
• pp.548-554
• /
• 1994

The high temperature fatigue crack growth behavior of SUS 304 stainless steel at $550^{\circ}C$ and $650^{\circ}C$ was investigated under various kinds of stress ratio and frequency in sinusoidal waveform on the basis of the non-linear fracture mechanics. The result arranging crack growth rate by modified J-integral J' showed influence of stress ratio and frequency. All the data obtained under the test at $550^{\circ}C$ were plotted within data band of da/dN-${\triangle}J_f$ relationship for cycle-dependent crack growth. On the basis of static creep and cycle-dependent data band; both time- and cycle-dependent crack growth behavior was observed under loading conditions at $650^{\circ}C$, but cycle-dependent crack growth behavior predominantly appeared and time-dependent crack growth behaviour was little observed under loading conditions at $550^{\circ}C$. Fractographic examinations for fracture surface indicated that the fracture mode was generally transgranular. The stripes were found on fracture surface and each stripe was accompanied by a crack tip blunting and an abrupt increase in the load-point displacement. The $J'_{an}$ had a validity in case of $650^{\circ}C, but scarcely had it in case of $550^{\circ}C$.