• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.4
• /
• pp.329-337
• /
• 2015

In this paper, a simulation based estimation method of energy consumption of the spindle and feed drives for the NC machine tool during the cutting process is proposed. To predict energy consumption of the feed drive system, position, velocity, acceleration and jerk of the table are analyzed based on NC data and then the power and energy are calculated considering friction force and mass of the stages. Energy consumption of the spindle is estimated based on models from acceleration motion of rotating parts, friction torque and power loss of motors. Moreover, simulation models of cutting power and energy for the material removal along the NC tool paths are proposed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.12
• /
• pp.2926-2935
• /
• 1993

Chip breaker selection analysis, only being possible through experimental process, was obtained by a applied equation which used an orthogonal cutting model and a basic chip deformation. This equation could present an analysis of the chip breaking phenomena without the use of an actual experimetal method, and it was applied to computer simulation and proved the validity of theory through actual experiments. From these results, an efficient method for finding the optimum conditions of chip breaking was found through an optimized theory being applied to basic program. A finite element model for simulating chip breaking in orthogonal cutting was developed and discussed. By simulation the animation of chip breaking is observed in process on the computer screen.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.5 no.2
• /
• pp.3-9
• /
• 2006

HSM(High-speed Machining) is widely used in rapid manufacturing of precision products and molds of various materials. Improvement in cutting efficiency is one of the important subjects in the HSM process. To analyse the dynamic behavior during a very short cutting time, the computational analysis code, LS-DYNA3D, was employed for the simulation of the mechanism of HSM for aluminium 7075. This cutting mechanism includes some difficult points in simulation, for example, material and geometrical non-linearity, high-speed dynamic impact, contact with friction, etc. In this paper, a finite element model considering the strain rate effect is proposed to predict the cutting phenomena such as chip deformation, strain and stress distributions, which will help us to design the HSM process.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1995.10a
• /
• pp.68-75
• /
• 1995

The milling process is one of the most important metal removal processes in industry. Due to the complexities inherent to the cutter insert geometry and the milling cutter kinematics, these processes leave an analytically difficult to predict texture on the machined surface's hills and valleys. The instantaneous uncut chip cross sectional area may be estimated by the relative position between the workpiece and the cutter inserts. furthermore, since the cutting forces are proportional to the instantaneous uncut chip cross sectional area, the cutting forces in face milling operations can not be estimated easily. A new simulation program which is based upon the numerical method has been proposed to estimate the cutting force components, with the ability to predict the machined surface texture left by the face milling operation.

• Geomechanics and Engineering
• /
• v.13 no.6
• /
• pp.977-995
• /
• 2017

It is well accepted that rock failure mechanism influence the cutting efficiency and determination of optimum cutting parameters. In this paper, an attempt was made to research the factors that affect the failure mechanism based on discrete element method (DEM). The influences of cutting depth, hydrostatic pressure, cutting velocity, back rake angle and joint set on failure mechanism in rock-cutting are researched by PFC2D. The results show that: the ductile failure occurs at shallow cutting depths, the brittle failure occurs as the depth of cut increases beyond a threshold value. The mean cutting forces have a linear related to the cutting depth if the cutting action is dominated by the ductile mode, however, the mean cutting forces are deviate from the linear relationship while the cutting action is dominated by the brittle mode. The failure mechanism changes from brittle mode with larger chips under atmospheric conditions, to ductile mode with crushed chips under hydrostatic conditions. As the cutting velocity increases, a grow number of micro-cracks are initiated around the cutter and the volume of the chipped fragmentation is decreasing correspondingly. The crack initiates and propagates parallel to the free surface with a smaller rake angle, but with the rake angle increases, the direction of crack initiation and propagation is changed to towards the intact rock. The existence of joint set have significant influence on crack initiation and propagation, it makes the crack prone to propagate along the joint.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.319-320
• /
• 2002

Numerical simulation of chip formation during high speed machining requires knowing the friction at tool/chip interface. This parameter is hardly identified and generally the loadings (temperature, force) during the identification are not similar to those encountered during machining. Thus, Coulomb friction identified with pin-on-disc device is often used to conduct numerical simulation. The used of this technique cannot leads to good numerical results of chip formation compared to the experimental tests especially in the case of low uncut chip thickness. In this contribution, we propose a new method to evaluate the friction at tool/chip interface. In fact several Coulomb friction parameters are identified corresponding to several parts of the cutting tool. Experimental tests have been conducted allowed us to determinate both the level and the distribution of the Coulomb friction. Experimental results are also compared to the results of orthogonal cutting simulation. We show that this technique allows predicting accuracy results of chip formation.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.19-25
• /
• 2001

In metal cutting, chatter is an unstable cutting phenomenon which is due to the interaction of the dynamics of the chip removal process and the structural dynamics of machine tool. When chatter occurs, it reduces tool life and results in poor surface roughness and low productivity of the machining process. In this study, the experiments have been conducted to investigate phenomenon of the chatter in CNC lathe without cutting fluid. In the experiments, two accelerometers were attached at the tail stock and tool holder and the signals were caught. In order to observe the effect of chatter on the surface roughness profiles, surface roughness profiles were generated under the ideal condition and the occurrence of the chatter based on the surface simulation model using surface-shaping system. Finally, the result of experiment and simulation have been compared.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.37-41
• /
• 2002

This study has been focused on the development of an open architecture CNC system and integration of core application technology for machine tool such as a remote monitoring/diagnosis system, NURBS interpolation, and cutting process simulation. To do this, we have developed a comprehensive CNC software including the basic HMI, screen editor, ASF, and visual builder. As a control hardware system for machine tool, the universal I/O module and CNC main unit have been developed. Then the remote monitoring/diagnosis system and NURBS interpolation have been implemented in the CNC software. The cutting simulation software will be used for enhancing the productivity of machine tools. Through a simulator and test bed, the whole technology has been verified.

• Korean Journal of Computational Design and Engineering
• /
• v.4 no.3
• /
• pp.247-258
• /
• 1999

With the contemporary CAD/CAM system, where the tool path is generated and verified purely based on the geometric operation, geometric accuracy of the machined surface cannot be guaranteed dut to the cutting mechanics, meaning that the cutting mechanics should be incorporated in some fashion. In this paper, we incorporate the instantaneous cutting force and the tool deflection phenomena in predicting the machined surface for the finish-cut and milling operation. For the given NC dat including cutting conditions, the developed algorithm computes cutting force and deflection amount along the tool trajectory, and outputs the 3D graphic model of the machined surface together with error analysis. The validity and accuracy of the presented method has been tested by the actual cutting experiments. Experimental results and accuracy enhancement method together with implementing architecture of the VMCS (Virtual Machining CAM System) are discussed in the paper.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.9
• /
• pp.960-966
• /
• 2007

High-efficient machining, which means to machine a part in the least amount of time, is the most effective tool to improve productivity. In this study, a new feed optimization method based on virtual manufacturing was proposed to realize the high-efficient machining in turning process through the cutting power regulation. The cutting area was evaluated by using the Boolean intersection operation between the cutting tool and workpiece. And the cutting force and power were predicted from the cutting parameters such as feed, depth of cut, spindle speed, specific cutting force, and so on. Especially, the reliability of the proposed optimization method was validated by comparing the predicted and measured cutting forces. The simulation results showed that the proposed optimization method could effectively enhance the productivity in turning process.