• Korean Journal of Computational Design and Engineering
• /
• v.21 no.2
• /
• pp.196-203
• /
• 2016

In this paper, we propose a virtual surgical planning system specialized to mandible reconstruction surgery. Mandible reconstruction surgery is one of the most difficult surgeries, even for experienced surgeons. Compared to the traditional surgical procedures, virtual surgical planning can reduce the operation time in operating room while expecting better surgical outcome with optimized planning. However, with existing software systems, it requires much time and manual operations in virtual surgical planning. To reduce preparation time and improve accuracy of virtual surgical planning, we have developed optimized functions for virtual surgical simulation of mandible reconstruction with user-friendly interface. We found that the proposed system shortened the preparation time by half compared to the existing system from the experiments. The proposed system supports surgeons to make accurate plan faster and easier. The virtually planned results are used to make surgical cutting guide by 3D printing, and this will enhance surgical performance in operating room.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.5 no.3
• /
• pp.23-30
• /
• 2002

In recently, using of steel reinforcements by reinforcing materials of the reinforced earth, micro-pile and root-pile etc,. is wide-spreading in the stabilizing control of cutting and embankment slopes, but the failure mechanism of reinforced earth as well as the effect of insert angles or types of reinforcement and others are not defined clearly. In this study, therefore heavy-duty direct shear tests were exercised on the reinforced soil and the non-reinforced soil, which was executed for research on the interaction of soil-reinforcement and theirs behavior. The hardness and softness and the standard sands were used for modeling of reinforced soil, the material constants for the computer simulation were estimated from the results of CD-Test. The effects of reinforcing and of friction increasing on the softness, area ratio of reinforcements is equal, were the better than them of the hardness, as well the reinforcing effects of shear strength without regard to the area ratio is much the same at $10^{\circ}$, insert angle of reinforced bar, differ from them of the existing study. Then, the results of numerical analysis showed that the behavior of reinforcements displayed bending resistance and shear resistance at $15^{\circ}$ and $30^{\circ}$, respectively. Also, the state of strain transfer was observed and the behavior of resistance mechanism on reinforcements presented almost the same them of landslides stabilizing pile.

• Journal of Korean Society of Transportation
• /
• v.22 no.7 s.78
• /
• pp.61-67
• /
• 2004

It is needed for one to design the better models estimating emission and then with the real time data, make the monitoring system simulating emission rate because of having built the basement of accepting real-time traffic information in ITS projects. The objective of the study is to develop the monitoring system visualizing air pollution to a certain place. It is based on the estimated emission from the patterns of individual vehicles and the changes of traffic flow. For constructing simulator, we loaded referring algorithm in actuality program and simulates the traffic flow movement in a microscopic viewpoint. The simulator is able to express not only the movement of each car but also to visualize processing the emission and diffusion of the air pollutant by computer program. Not only expresses the simulation process the angle of vision but it also cutting down environment expenses and improving the traffic impact assessment and the traffic impact assessment.

• Journal of Navigation and Port Research
• /
• v.38 no.6
• /
• pp.623-627
• /
• 2014

In recent years, wireless communication technologies in human body have received an increasing attention and the research on an antenna that can be worn also has been actively conducted. In this paper, an wearable antenna that can receive GPS signal frequency is proposed. The antenna was manufactured by using a copper polyester fabric with thickness of 0.08mm as a radiator and a ground plate, and a goatskin with thickness of 0.7mm as dielectric substrate. Cutting edges placed in diagonal direction of square patch in order to obtain a circular polarization characteristic, and the conductive cloth and leather was laminated by using a conductive epoxy. First, goatskin dielectric constant was obtained through the simulation and measurement of resonance frequency of the three square patch antennas with different size. On the basis of the results, an antenna operating in the GPS band was designed and the performance of the antenna was validated by making the experiment. The change of the characteristic of the antenna that is located on the shoulder parts of the clothing and wearing person were measured. And it was confirmed that the reception sensitivity has a similar level as compared to the commercially produced ceramic GPS antenna.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.340-343
• /
• 2007

OFDM (Orthogonal Frequency Division Multiplexing) system is robust to frequency selective fading and narrowband interference in high-speed data communications. However, an OFDM signal consists of a number of independently modulated subcarriers, which can give a large PAPR (peak-to-Average Power Ratio) when added up coherently. In this paper, we propose a new PAPR reduction method using Adaptive Sine Soft Clipping (ASS Clipping) to solve the PAPR problem. The proposed method reduce the PAPR and out-of-band spectrum by cutting down high frequency components. From computer simulation results, we analyze the PSD (Power Spectral Density) and BER (Bit Error Rate) performance as well as PAPR reduction performance when the ASS Clipping method is applied to OFDM system.

• Journal of Mechanical Science and Technology
• /
• v.19 no.5
• /
• pp.1158-1168
• /
• 2005

A shunt from the left ventricle to the left anterior descending artery is being developed for coronary artery occlusive disease, in which the shunt or conduit connects the the left ventricle (LV) with the diseased artery directly at a point distal to the obstruction. To aid in assessing and optimizing its benefit, a computational model of the cardiovascular system was developed and used to explore various design conditions. Computational fluid dynamic analysis for the shunt hemodynamics was also done using a commercial finite element package. Simulation results indicate that in complete left anterior descending artery (LAD) occlusion, flow can be returned to approximately 65% of normal, if the conduit resistance is equal for forward and reverse flow. The net coronary flow can increase to 80% when the backflow resistance is infinite. The increases in flow rate produced by asymmetric flow resistance are enhanced considerably for a partial LAD obstruction, since the primary effect of resistance asymmetry is to prevent leakage back into the ventricle during diastole. Increased arterial compliance has little effect on net flow with a symmetric shunt, but considerably augments it when the resistance is asymmetric. The computational results suggest that an LV-LAD conduit will be beneficial when the resistance due to artery stenosis exceeds 27 PRU, if the resistance is symmetric. Fluid dynamic simulations for the shunt flow show that a recirculating region generated near the junction of the coronary artery with the bypass shunt. The secondary flow is induced at the cutting plane perpendicular to the axis direction and it is in the attenuated of coronary artery.

• Korean Journal of Optics and Photonics
• /
• v.3 no.4
• /
• pp.227-233
• /
• 1992

The simulation code was developed for the development of the split-disk geometry glass amplifier, which could design the laser apparatus and analyze the properties of the laser system. The flashlamp emission energy at the short wavelength region must be reduced, while maintaining a current density between 2000 and 4000 A/$\textrm{cm}^{2}$, in order to reduce the thermal loading in the laser glass and to raise the coupling efficiency between the emission spectrum of the flashlamps and the absorption spectrum of the laser glass. By cutting the laser glass into three equal pieces, the temperature rise in the laser glass dropped by 70% due to the efficient removal of the heat in the laser glass. It was found that the $Nd^{3+}$ doping rate of each laser glass should be properly selected and the optimum value of the product of the absorption coefficient $\alpha$ and the thickness d of the laser glass is about 0.26 in the split-disk geometry.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.2
• /
• pp.257-262
• /
• 2017

In this paper, we proposed a rectangular planar monopole antenna with a double sleeve that applied to a half-cut and a discontinuous feed structure. A rectangular planar monopole antenna with a double sleeve was cut in half along the magnetic symmetry line, and impedance matching was achieved by a discontinuous structure was applied to a feeder and by adjusting the double sleeve gap. We used the HFSS simulator of ANSYS company to confirm the antenna parameter property, and the antenna size was $21{\times}40mm^2$. In the proposed antenna, the simulation frequency range with VSWR of 2 or less was 2.6GHz to 10.25GHz. The bandwidth was 7.65GHz. The frequency range of the fabricated antenna was 3.3GHz to 9.75GHz, and the bandwidth was 6.45GHz. The measured radiation pattern frequencies were 3.5GHz, 5.5GHz, 7.5GHz, and 9.5GHz. A radiation pattern similar to the dipole antenna pattern was obtained at all frequencies.

• Journal of the Korea Computer Graphics Society
• /
• v.26 no.3
• /
• pp.21-29
• /
• 2020

This study defines the pipeline for digital fashion contents production using CLO 3D, a 3D fashion design software that supports virtual clothing visualization as a cutting-edge simulation technology for fashion, and vuforia, a mobile platform augmented reality (AR) development kit for creating AR applications. The proposed production pipeline is organized in a method to produce a virtual clothing model through CLO 3D software through works of patterns, sewing lines, textures, etc., and AR contents based on computer vision techniques using the functions and properties of vuforia development kits in the Unity engine development environment. In addition, we present application method that can be practically utilized from the perspective of practical users, such as fashion designers and directors, by creating a new type of AR digital fashion contents directly as a flow of the defined production pipeline.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1996.06b
• /
• pp.285-309
• /
• 1996

Non oxide ceramics such as nitrides of transition metals have shown significant potential for future economic impact, in diverse applications in ceramic, aerospace and electronic industries, as refractory products, abrasives and cutting tools, aircraft components, and semi-conductor substrates amid others. Combustion synthesis has become an attractive alternative to the conventional furnace technology to produce these materials cheaply, faster and at a higher level of purity. However he process os highly exothermic and manifests complex dynamics due to its strongly non-linear nature. In order to develop an understanding of this process and to study the effect of operational parameters on the final outcome, numerical modeling is necessary, which would generated essential knowledge to help scale-up the process. the model is based on a system of parabolic-hyperbolic partial differential equations representing the heat, mass and momentum conservation relations. The model also takes into account structural change due to sintering and volumetric expansion, and their effect on the transport properties of the system. The solutions of these equations exhibit steep moving spatial gradients in the form of reaction fronts, propagating in space with variable velocity, which gives rise to varying time scales. To cope with the possibility of extremely abrupt changes in the values of the solution over very short distances, adaptive mesh techniques can be applied to resolve the high activity regions by ordering grid points in appropriate places. To avoid a control volume formulation of the solution of partial differential equations, a simple orthogonal, adaptive-mesh technique is employed. This involves separate adaptation in the x and y directions. Through simple analysis and numerical examples, the adaptive mesh is shown to give significant increase in accuracy in the computations.