• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2008년도 정기총회 및 학술발표대회
• /
• pp.577-580
• /
• 2008

The purpose of this study is the stability evaluation of soil slope according to inclination of upper natural slope. Upper natural slope breeds loss of slope by inflow in slope of surface water by rainfall and fluctuation of amount of materials in slope through method of cutting slope according to degree of inclination. Basis of standard inclination does not consider of inclination of upper natural slope and is presented uniformly. Therefore, in this study, analyzed stability of inclination of upper natural slope through limit equilibrium analysis.

• 한국지반환경공학회 논문집
• /
• 제5권4호
• /
• pp.73-79
• /
• 2004

도로주변 절토사면 상부에 설치되는 산마루측구는 강우시 상부로부터 흘러내려오는 지표수를 원활히 배수시켜, 절토면으로 유입되는 것을 방지하기 위해 설치한다. 그러나, 산마루측구 설치시 시공여건상 품질관리가 어려워, 절토면 배면으로부터의 지표수를 원활히 배수시키지 못하는 문제점을 안고 있다. 따라서, 본 논문에서는 비탈면 상부에 설치된 산마루측구의 기능을 지반 및 지형조건, 강우조건에 따라 비탈면 안정성에 미치는 영향을 평가함으로써, 현재 설계 시공되고 있는 산마루측구의 설치 적정성을 평가하였다. 평가결과 산마루측구는 평균적으로 강우시 약 3%의 안전율 증대효과가 있는 것으로 검토되었다.

• 한국산학기술학회논문지
• /
• 제12권2호
• /
• pp.852-857
• /
• 2011

조선업종은 숙련공의 감소와 노동력 부족을 해결하기 위해 자동화와 기계화가 필요하다. 특히 조선용 핸드레일 제조공정은 표준화된 타 분야와 달리 자동화가 낙후되어 있다. 본 연구에서는 조선용 핸드레일 제작에 사용할 수 있는 철의장 가공자동화시스템을 설계하고 개발하였다. 시스템의 기구부는 절단공정의 효율성, 생산성, 안정성 등을 고려하여 설계하였고, CATIA 와 ANSYS를 사용하여 구조물의 안정성을 확인하였다. 시스템 제어부는 개방성과 확장성을 제공하는 PCNC 콘트롤러를 사용하였고, 터치스크린 방식의 화면 조작을 통해 시스템의 제어 및 모니터링을 할 수 있도록 구축하였다. 개발된 철의장 가공자동화시스템은 수차의 구동테스트 및 가공테스트를 통해 성능의 우수성을 입증하여 실용단계에 있다.

• Structural Engineering and Mechanics
• /
• 제59권5호
• /
• pp.933-950
• /
• 2016

Decks, interior beams, edge beams and girders are the parts of a steel floor system. If the deck is optimized without considering beam optimization, finding best result is simple. However, a deck with higher cost may increase the composite action of the beams and decrease the beam cost reducing the total cost. Also different number of floor divisions can improve the total floor cost. Increasing beam capacity by using castellated beams is other efficient method to save the costs. In this study, floor optimization is performed and these three issues are discussed. Floor division number and deck sections are some of the variables. Also for each beam, profile section of the beam, beam cutting depth, cutting angle, spacing between holes and number of filled holes at the ends of castellated beams are other variables. Constraints include the application of stress, stability, deflection and vibration limitations according to the load and resistance factor (LRFD) design. Objective function is the total cost of the floor consisting of the steel profile cost, cutting and welding cost, concrete cost, steel deck cost, shear stud cost and construction costs. Optimization is performed by enhanced colliding body optimization (ECBO), Results show that using castellated beams, selecting a deck with higher price and considering different number of floor divisions can decrease the total cost of the floor.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2001년도 춘계학술발표회 초록집
• /
• pp.3-3
• /
• 2001

Recently TiN, TiAlN, CrN hardcoatings have adapted many industrial application such as die, mold and cutting tools because of good wear resistant and thermal stability. However, in terms of high speed process, general hard coatings have been limited by oxidation and thermal hardness drop. Especially in the case of PCB drill, high speed cutting and without lubricant process condition have not adapted these coatings until now. Therefore more recently, superhard nanocomposite coating which have superhard and good thermal stability have developed. In previous works, WC-TiAlN new nanocomposite film was investigated by cathodic arc ion plating system. Control of AI concentration, WC-TiAlN multi layer composite coating with controlled microstructure was carried out and provides additional enhancement of mechanical properties as well as oxidation resistance at elevated temperature. It is noted that microhardness ofWC-TiA1N multi layer composite coating increased up to 50 Gpa and got thermal stability about $900^{\circ}C$. In this study WC-TiAlN nanocomposite coating was deposited on PCB drill for enhancement of life time. The parameter was A1 concentration and plasma cleaning time for edge sharpness maintaining. The characteristic of WC-TiAlN film formation and wear behaviors are discussed with data from AlES, XRD, EDS and SEM analysis. Through field test, enhancement of life time for PCB drill was measured.

• 한국지반공학회논문집
• /
• 제24권8호
• /
• pp.81-88
• /
• 2008

본 연구에서는 절토사면 공법선정시 고려해야 할 영향인자와 일반적으로 시공되고 있는 사면보강공법에 대한 합리적 분석을 위해 많은 의사결정기법 중 가장 광범위하게 사용되는 AHP기법을 이용하였다. 공법선택시 고려해야할 항목에 대한 가중치 중 안정성 및 내구성이 가장 중요한 평가요소로 분석되었으며, 안정성 및 내구성, 환경성이 공법선 택시 전체 비중의 50%이상을 차지하는 것으로 나타났다. 안전율 증가법 위주로 조사된 절토사면 보강공법에 대한 선호도 조사에서 보강토옹벽, 콘크리트옹벽과 절토공법이 가장 선호도가 높은 공법으로 조사되었다. 또한 실제 현장사례에 대해 적용한 결과 4가지 대안 중 절토공법이 최적대안으로 선정되어 가중치가 높은 특정 평가요소의 우수성보다는 모든 평가요소에서 고른 우수성이 현실적인 공법 선정과정에서 중요한 요소임을 알 수 있었다.

• 한국농공학회지
• /
• 제17권4호
• /
• pp.3897-3920
• /
• 1975

Since the most of Korean dairy and cattle raising farms are too small to introduce western mechanized farming, it is necessary to develope small size equipments. This study has been carried to develop a rotary mower as on attachment of 8 to 10 horse powertiller which is widely spread in rural area. It will not ony be helpfull for the farmers to harvesting hay grass but also desirable to increase the power tiller utility. The protto type rotary mower designed through the fundamental investigations, has been modified and improved through the field trials, and a series of field tests has been carried to investigate its performance and economic feasibility comparing with existing vailable harvesting equipments. The results are as follows; 1. To increase the stability, two guide wheels are attached to both side of the protto type rotary mower. 2. To prevent the clinging of tall grasses, the vertical driving shafts are covered with cylindrical protectors. 3. The cutting height is adjustable in 8 steps from 2.5 to 20 centimeters by changing the length of guide wheel legs. 4. The practical Critical cutting speed were always higher than theoretical value in both case of single cutting blade and three when the cutting depth was 25 millimeter. 5. The peripheral speed of cutting blade was varied in response to the change of engine speed, mean while the peripheral speed was adequate as it was changhed from 25 to 35 meter per second when the power tiller is operated in proper working ground speed. 6. The time requirement to harvest 10 a were 88.7, 54.6 and 41.4 minutes for the first, second and third stage of ground speed respectively, and because of the difficulty of delivery, it was observed that operating with fourth stage of ground speed was not recomanendable when the grass height is taller than 90 centimeters. 7. The performance of rotary mower were 1.1-1.7, 1.4-4.0, 3.8-11.8 and 7.4-22.0 times of reciprocating mower, portable disc type cutter, hay scythe and ordinary sickle respectively. 8. When the slope exceeds, 20 degree the downward harvesting operation was impossible because of the excessive front end weight, while less than 5 degree of land slope did not effect in field operation. 9. Increased traveling spee caused higher cutting height and slight cutting failure, but seems not to effect to the gross yield, and the efficiency of cutting width were from 83 to 94 precent. 10. Tn rank of economy were rotary mower (3,2 stage operation), reciprocating mower, hay scythe, portable disc type cutter and sickle in order when the annul operation exdeeds 100 hours. From the above results, it is convinced that the protto type rotary mower is good enough to the livestock farmers as a hay harvesting equipment because of its economy, hardiness in operating and its out standing performance and hopefully it will contribute to the extension of Korean livestock farming.

• 한국공작기계학회논문집
• /
• 제10권4호
• /
• pp.97-103
• /
• 2001

The study on the high-speed machine tool is very important for the improvement of productivity since it can shortens cutting and non-cutting time. Especially, high speed of feed drive system is the major research field. In the industries of the advanced countries, the feed drive systems at the speed of 60 m/min have been already developed based on the high lead ball screws. In this study, a high speed feed drive system at the speed of 60 m/ min has been developed, and its movements characteris-tics are investigated. As the movement characteristics, positioning accuracy, angular accuracy, straightness and micro step-response are measured. Thermal characteristics of the system is also discussed. For measuring the movement characteris-tics, a laser interferometer, a memory-based Hi-coder and a cooling device are used. The experimental results confirm that the movement characteristics and the thermal behavior of the system are satisfactory in the aspect of accuracy and stability.

• Tribology and Lubricants
• /
• 제4권2호
• /
• pp.44-51
• /
• 1988

Titanium carbide(TiC), Titanium nitride(TiN), and Titanium carbonnitride(Ti(C,N)) films were deposited on $Si_3N_4$-TiC composite cutting tools by chemical vapor deposition(CVD) using $TiCl_4-CH_4-H_2$, $TiCl_4-N_2-H_2$, and $TiCl_4-CH_4-N_2-H_2$ gas mixtures, respectively. The experimental results indicate that TiC coatings compared with TiN coatings on $Si_3N_4$ -TiC ceramic have an improved microstructural property, good thermal shock resistance, and good interfacial bonding. However TiN coatings compared with TiC coatings have a low friction coefficient with steel and good chemical stability. It is found by cutting test that coated insert compared with $Si_3N_4$-TiC ceramic have a superior flank and crater wear resistance. And multilayer coating compared with monolayer coating shows a improved wear resistance.

• 한국정밀공학회지
• /
• 제12권1호
• /
• pp.15-21
• /
• 1995

Automatic monitoring of cutting process is one of the most important technologies for increasing the stability and the reliability of unmanned manufacturing system. In this study, the methods which use laser displacement signals and banded energy method are proposed to monitor chatter vibration in the turning process. From this method, the monitoring system of the chatter vibration was developed and investigated its practical possibility. As a result, it is shown by experiments that the chatter vibration can be detected accurately, and it can be widely used in most turning processes.