• 한국정밀공학회지
• /
• 제29권3호
• /
• pp.279-288
• /
• 2012

The material removal mechanism in machining is significantly affected by the cutting edge geometry. Its effect becomes even more substantial when the depth of cut is relatively small as compared to the characteristic length which represents the shape and size of the cutting edge. Conventionally, radius or focal length has been employed as the characteristic length with the assumption that the shape of cutting edge is round or parabolic. However, in reality, there could be various ways to determine the radius or focal length even for the same tool edge profile, depending on the region to be considered as cutting edge in the measured profile and the constraints to be set in constructing the best fitted circle or parabola. In this regard, the present study proposes various models to determine the characteristic length in terms of radius or focal length. Their physical compatibility are validated by carrying out 2D orthogonal cutting experiments using inserts with a wide range of characteristic length ($30{\sim}180\;{\mu}m$ in terms of radius) and then by investigating the correlation between the characteristic length and the cutting forces. Such validation is based on the common belief that the larger the characteristic length is, the blunter the cutting edge is and the higher the cutting forces are. Interestingly, the results showed that the correlation is higher for the radius or focal length obtained with a constraint that the center of best fitted circle or the focus of the best fitted parabola should be on the bisectional line of the wedge angle of tool.

• 대한산업공학회지
• /
• 제27권1호
• /
• pp.69-88
• /
• 2001

In the zigzag milling operation, an important issue is to design a machining strategy which minimizes the cutting time. An important variable for minimization of cutting time is the tool path length. The tool path is divided into cutting path and non-cutting path. Cutting path can be subdivided into tool path segment and step-over, and non-cutting path can be regarded as the tool retraction. We propose a new method to determine the cutting direction which minimizes the length of tool path in a convex or concave polygonal shape including islands. For the minimization of tool path length, we consider two factors such as step-over and tool retraction. Step-over is defined as the tool path length which is parallel to the boundary edges for machining area and the tool retraction is a non-cutting path for machining any remaining regions. In the determination of cutting direction, we propose a mathematical model and an algorithm which minimizes tool retraction length in complex shapes. With the proposed methods, we can generate a tool path for the minimization of cutting time in a convex or concave polygonal shapes including islands.

• 펄프종이기술
• /
• 제40권2호
• /
• pp.57-64
• /
• 2008

In general, the entire of paper mulberry bark, which is not cut into pieces with an appropriate length, have been used in the pulping. This kind of pulping method couldn't accomplish the improvement of beating and sheet forming efficiency. For this reason, we investigated the effects of the cutting length of paper mulberry bast fiber on pulping and Hanji (Korean traditional paper) properties, in order to develop high quality Hanji manufacturing process. The cutting length variation of paper mulberry white bast did not great effects on pulp yields. The pulp yields based on pulping methods were sulfomethylated pulping av. 57.4%, alkali-hydrogen peroxide pulping av. 55.4%, and alkaline pulping av. 53.5% respectively. The optical properties such as brightness, opacity, scattering coefficient, and absorption coefficient were slightly improved by the increase of paper mulberry white bast cutting length. The increase of paper mulberry white bast cutting length resulted in poor sheet formation. Physical properties such as breaking length, TEA, tear index, burst index, and folding endurance were slightly improved by the increase of cutting length. The modified pulping processes, which used sulfomethylated method and alkali-hydrogen peroxide method, showed better pulp and sheet properties than conventional alkaline pulping.

• 원예과학기술지
• /
• 제30권1호
• /
• pp.13-20
• /
• 2012

본 연구는 스탠다드 국화 '백마' 품종의 플러그 묘 생산에 있어서 삽수의 조건이 지상부 생육과 발근 및 정식 후의 절화 생육에 미치는 영향을 알아보고자 실시하였다. 삽수에 잎을 많이 부착할수록 삽목묘의 지상부 생육이 양호하였고, 잎을 4-6장 부착하여 삽목하는 것이 다른 처리에 비해 발근에 효과적이었다. 삽수길이에 따른 삽목묘의 지상부 생육은 큰 차이가 없었으며, 삽수길이를 5-7cm로 처리하는 것이 발근상태가 양호하였다. 삽수 굵기는 3.1mm 처리에 비해 3.6mm와 4.2mm 처리에서 삽목묘의 지상부 생육과 발근이 양호하였다. NAA 처리농도가 높을수록 삽목묘의 지상부 생육이 억제되었으며, 뿌리의 길이도 짧아졌다. NAA $100mg{\cdot}L^{-1}$를 1시간 처리하여 삽목하는 것이 삽목묘의 지상부 생육과 발근에 효과적이었다. 피트모스와 펄라이트를 2:2로 혼합한 배지에서 다른 처리에 비해 뿌리의 길이, 수 및 무게 등이 뿌리의 생육이 양호하였다. 잎이 적은 것보다 4-6개 부착된 삽수의 삽목묘를 정식했을 때, 절화장이 길고, 무게가 무거웠으며, 엽수도 많았다. 삽수길이에 있어서 7-9cm 처리가 절화장, 절화무게, 설상화 수 등 전반적인 절화의 생육에 효과적이었다. 따라서 '백마' 플러그 묘 생산시 7cm 길이에 3.6mm 굵기의 4-6장의 잎을 부착한 삽수를 삽목하는 것이 삽목묘의 지상부 생육과 발근 및 정식 후의 절화 생육을 위해 바람직하였다.

• 한국산업융합학회 논문집
• /
• 제5권3호
• /
• pp.201-208
• /
• 2002

The machine tool which operates by hand is replacing by CNC machine tool to improve the quality of the product and the productivity in modem mechanic industry. The precision of machine part is influenced greatly the surface roughness by cutting condition of machine tool. So this study was performed to examine the aluminium surface roughness of section according to change of strength rating, nose radius, cutting speed, using live center. The results of this study are as follows; 1. In the case of 56mm diameter of test piece(length is below triple of diameter), whether establish the live center or not, doesn't influence to the surface roughness, and it is possible to make product without the live center. 2. The average surface roughness of 42mm diameter(length is quadruple of diameter) is similar to the 56mm diameter in the cutting condition of nose radius 0.8mm and cutting speed 140mm/min, but there are increases and differences in other cutting conditions. 3. In the case of test piece length more 70m/min(140m/mm) and nose radius improved greatly using the live center. 4. In the case of test piece length is quintuple of diameter, the nose radius must choose big tool and increase the cutting speed in preference live center establishment availability to improve that is surface roughness. Conclusively, if aluminum test piece length is fewer than triple of diameter, can process without establishing live center. If aluminum test piece length is more than quintuple of diameter, cutting conditions to improve surface roughness are (1) cutting speed (2) nose radius (3) whether the live center uses or not.

• 오토저널
• /
• 제9권5호
• /
• pp.49-56
• /
• 1987

This paper is a study on the effect of the cutting speed on the tool wear in turning of the glass fiber reinforced plastics. The wear behavior of cutting tool is studied by means of turning, changing the cutting speed and feed in the wide range. Moreover, the theoretical model applicable to the cutting speed of wide range is analysed. The main results obtained are as follows: The relation between the tool wear and the cutting speed is divided into three range in case of the constant cutting distance. 1) At the low cutting speed, the tool wear is independent of the cutting speed, but dependent mainly on the contact length between tool and glass fiber(lst range). 2) At the high cutting speed, the tool wear is independent of the contact length, and dependent on the cutting speed only(2nd range). The tool wear increases in proportion to the cutting speed. 3) At the higher cutting speed than the speed in the 2nd range, the tool wear is independent both of the cutting speed and the contact length(3rd range). 4) In the 3rd range, tool flank wear is constant and is observed that only the wear of cutting edge increases.

• 한국생산제조학회지
• /
• 제9권2호
• /
• pp.72-79
• /
• 2000

A new optimal tool design model which can be minimized the resultant cutting forces under the constrains of variables was developed. The resultant cutting forces are used as the objective function and tool angles are used as the variables. Cutting experiments of tool wear and chip length using the new and conventional tools wee carried out. Tool life of optimized cutter are more increased than those of conventional cutter by 2.29 times and 2.52 times at light and at heavy cutting conditions respectively. Chip length of optimized cutter are more increased than those of conventional cutter It is considered that the decrease of the resultant cutting forces is the cause that an effective rake and shear angles by the shape of optimal cutter.

• 한국기계가공학회지
• /
• 제11권3호
• /
• pp.80-85
• /
• 2012

The ultrasonic cutting method is which cutting by applying high frequency vibrational energy into specific area at constant pressure. Ultrasonic cutting is consisted of power supply, transducer, booster and cutting tool. Precise designing is required since each part's shape, length and mass can affect driving frequency and vibration mode. This paper focused to cutting tool design, its length L was set by calculating vibration equation. And the value of the shape parameter a was diversified as the integral multiple and the result of 40,189Hz the analysis of Modal was shown in the length 30mm of the result of performance b in the 11th mode Also by performing harmonic response analysis, the frequency response result was 40,189Hz, which was similar to modal analysis result.

• 대한산업공학회지
• /
• 제28권2호
• /
• pp.128-138
• /
• 2002

In this paper, we address how to reduce the length of tool retraction in a zigzag pocket machining. Tool retraction, in a zigzag pocket machining, is a non-cutting operation in which the tool moves to any remaining regions for machining. We developed an algorithm of generating tool retraction length in convex or concave polygonal shapes including islands. In the algorithm, we consider concave areas of cutting direction in the polygonal shape. Considering concave areas of cutting direction, the polygonal shape is decomposed to subregions which do not need any tool retraction. Using the proposed algorithm, we calculated the shortest length of tool retraction in cutting direction. Examples are shown to verify the validity of the algorithm.

• 화훼연구
• /
• 제17권4호
• /
• pp.256-261
• /
• 2009

본 연구는 하국용으로 가장 많이 재배되고 있는 '백선' 품종의 플러그 묘 생산에 있어서 삽수의 조건이 묘의 지상부 생육과 발근 및 절화생육에 미치는 영향을 알아보고자 실시하였다. 삽수에 부착된 엽수가 많을수록 묘의 지상부 생육과 발근이 양호하였다. 삽수 길이에 따른 지상부 생육에는 큰 차이가 없었으나, 발근은 삽수 길이가 5cm 이상인 처리에서 양호하였다. 삽수의 굵기가 굵을수록 지상부의 생체중이 무거웠으며, 굵기가 5.5 mm 처리에서 형성된 뿌리수가 가장 많았다. 삽수에 부착된 엽수가 많을수록 절화장이 길었고, 절화무게도 무거웠다. 삽수의 길이가 7~11 cm 처리에서 절화장, 절화무게, 엽수, 설상화수 등 절화의 생육이 양호하였다. 삽수 굵기가 5.5 cm 처리에서 다른 처리에 비해 절화 생육이 우수하였다. 띠라서 '백선' 플러그 묘 생산시 굵기가 5.5 mm 정도의 7cm 길이의 삽수에 잎을 4장 부착하여 삽목하는 것이 묘의 생육 및 발근에 효과적이고, 정식 후 절화의 생육에도 적합하였다.