• 한국공작기계학회논문집
• /
• 제13권1호
• /
• pp.9-15
• /
• 2004

In this study, experiments were conducted with an ultra-precision machine, developed in domestic, to find the characteristics and the most suitable cutting conditions of ultra-precision machining. To maximize the performance of the machine, the machine was installed in a room that is protected from vibration and is maintained constant temperature and constant humidity. Selected work pieces are an aluminum-alloyed material, which has excellent corrosion resistance and has low deformation. The used tool is synthetic poly crystal diamond, which has excellent abrasion resistance and has low affinity. Four types of tool nose radius were used such as 0, 0.1, 0.2 and 0.4mm. Machining is performed with cutting speed of 500, 800 and 1000m/min., feed rate of 0.005, 0.008, 0.010mm/rev. and cutting depth of 0.0005, 0.0025 and 0.005mm respectively which can generally be used in the field as a cutting condition. As a method of evaluation, surface roughness was measured for each cutting condition, and reciprocal characteristics are computed for each tool nose radius, cutting speed, feed rate and cutting depth. As a result, the most suitable cutting condition and characteristics of ultra-precision machining were identified which can usefully be applied in the industrial field.

• International Journal of Precision Engineering and Manufacturing
• /
• 제4권4호
• /
• pp.19-24
• /
• 2003

In end milling process, which is characterized by the use of a rotating tool, the undeformed chip thickness varies periodically with phase change of the tool. Although many efforts have concentrated on the study of end milling process, the analysis of shear and chip-tool friction behaviors has not been reported. Recently, a model has been proposed to simulate the shear and friction characteristics of an up-end milling process in terms of the equivalent oblique cutting. In the current study, the varying undeformed chip thickness and the cutting forces in a down-end milling process are replaced with the equivalent ones of oblique cutting. Then it is possible to simulate the shear and the chip-tool friction characteristics of a down-end milling process. The proposed model has been verified through two sets of cutting tests i.e., down-end milling and the equivalent oblique cutting tests. The experimental results show that the proposed model is suitable to analyze the shear and chip-tool frictional characteristics of down-end milling process. The specific cutting energy decreases with increase in equivalent undeformed chip thickness in a down-end milling process.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.426-429
• /
• 2003

In this study, phase transformation characteristics of Nitinol shape memory alloy with 54.5wt%Ni-45.5wt%Ti were investigated by varying with annealing treatment and cutting conditions through DSC(differential scanning calorimetry). Annealing treatment conditions were considered as heat treated time of 5 min, 15 min, 30 min, and 45 min, heat treated temperature of 40$0^{\circ}C$, 50$0^{\circ}C$, 5$25^{\circ}C$, 55$0^{\circ}C$, 575$^{\circ}C$, $600^{\circ}C$, $700^{\circ}C$, 80$0^{\circ}C$, and 90$0^{\circ}C$, and environmental condition of heat treatment under vacuum or air. Cutting conditions were considered as no cutting, one side cutting, and two side cutting. Tensile test was also conducted on Nitinol shape memory alloy to investigate thermomechanical characteristics by varying with annealing heat treatment histories. According to the results, annealing treatment and cutting conditions were found to significantly affect on phase transformation and thermomechanical characteristics of Nitinol shape memory alloy.

• 산업경영시스템학회지
• /
• 제45권3호
• /
• pp.104-114
• /
• 2022

The purpose of using coolant in machining is both to increase a tool life and also to prevent product deformation and thus, stabilize the surface quality by lubricating and cooling the tool and the machining surface. However, a very small amount of cutting mist should be used because chlorine-based extreme pressure additives are used to generate environmental pollutants in the production process and cause occupational diseases of workers. In this study, medical titanium alloy (Ti-6Al-7Nb) was subjected to a processing experiment by selecting factors and levels affecting cutting power in the processing of the Aerosol Dry Lubrication (ADL) method using vegetable oil. The machining shape was a slot to sufficiently reflect the effect of the cutting depth. As for the measurement of cutting force, the trend of cutting characteristics was identified through complete factor analysis. The factors affecting the cutting force of ADL slot processing were identified using the reaction surface analysis method, and the characteristics of the cutting force according to the change in factor level were analyzed. As the cutting speed increased, the cutting force decreased and then increased again. The cutting force continued to increase as the feed speed increased. The increase in the cutting depth increased the cutting force more significantly than the increase in the cutting speed and the feed speed. Through the reaction surface analysis method, the regression equation for predicting cutting force was identified, and the optimal processing conditions were proposed. The cutting force was predicted from the secondary regression equation and compared with the experimental value.

• 한국공작기계학회논문집
• /
• 제14권1호
• /
• pp.8-14
• /
• 2005

The purposes of using cutting fluid during cutting have been cooling, lubricating, chip washing, and anti-corroding. However, the present manufacturing industry restricts the use of cutting fluid because cutting fluid contains poisonous substances which are harmful to the human body. Therefore dry cutting becomes an unavoidable assignment and a lot of researches have studied cutting methods without using cutting fluid. Because dry turning is a continuous work, tools life is reduced by continuous heat generation and surface gets rough due to reduced lubrication, so it is important to consider these situations. In this paper, the way of selecting the optimal machining condition by the minimum number of experiments and the effectiveness of using compressed air in high hardness materials through Taguchi method have been found. Dry cutting using compressed air showed better cutting characteristics than normal dry cutting with respect to by cutting force, tool wear, and surface roughness. Also, the optimal machining condition f3r dry cutting using compressed air could be selected through Taguchi method.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 추계학술대회 논문집
• /
• pp.192-197
• /
• 2002

In this study, examined the cutting characteristics of alumuminum alloy AC8A-T6 that is used to present car piston materials. And in been holding materials machining empirically escape as result that experiment comparison changing the cutting speed and feed on various condition to choose efficient machining condition. The following results can be summarized from this research. 1. As the cutting speed decreased, principal cutting force and thrust cutting force is increased, and reason that cutting force interacts greatly in the low cutting speed is thought by result by BUE's stabilization. 2. The feed speed and cutting speed increase, friction factor is decrescent and the cause appeared the thrust cutting force is fallen than cutting force relatively because chip flow according to increase of the feed rate is constraint. 3. Though specific cutting resistance grows cutting area and the feed rate are few, the cause was expose that shear angle decreases by rake face of tool gets into negative angle remarkably as wear of a cutting tool or defect part of workpiece is cut. 4. Cutting speed do greatly depth of cut is slow, surface roughness examined closely through an experiment that becomes bad, and know that it can get good surface that process cutting speed because do feed rate by 0.1mm/rev low more than 250m/min to get good surface roughness can.

• Journal of Biosystems Engineering
• /
• 제20권1호
• /
• pp.3-12
• /
• 1995

This study was conducted to investigate the cutting mechanism of the reciprocating knife of combine harvester. The cutting operation of reciprocating knife was demonstrated through the cutting pattern diagram which was drawn by computer graphics. Various kinds and dimensions of standard-type reciprocating knives were analyzed by the developed program. The results are summarized as follows : (1) For the 50mm standard reciprocating knife, the bunching area and the maximum stalk-deflection were decreased rapidly according to the increase of cutting velocity ratio by 1.0 and decreased very slowly over this ratio. But, the secondary cut was occurred at ratio of 1.0 and increased rapidly over this ratio. (2) The 76mm standard knife showed better cutting mechanism than the 50mm, in two respects : the larger cutting area per one stroke and the lower revolutional speed of crank shaft for the same cutting velocity. (3) In respect to the bunching area and the secondary cutting length, the adequate height of 50mm standard reciprocating knife was 45~50mm. (4) In order to maintain the proper cutting mechanism, the adequate cutting velocity at forward speed of 0.5㎧ to 1.2m/s was from 0.4m/s to 1.2m/s for the standard knife.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.1051-1054
• /
• 2002

Environmentally conscious machining and technology have been taking more and more important position in machining process. Since cutting fluid has some impact on environment, many researches are being carried out to minimize the use of cutting fluid. It can be Increased the environmental pollution through not using coolant any more or minimizing it. In this study, the cooling effects of cutting methods using the compressed cold air, dry cutting and cutting fluid will investigate in the blade machining. In order to examine the characteristics of cutting and tool in the environmentally conscious machining, this work investigates experimentally the degree of tool wear, cutting force and characteristics of surface roughness in relation to machining conditions and cooling methods.

• 한국정밀공학회지
• /
• 제25권2호
• /
• pp.28-34
• /
• 2008

Recently, with the development of high speed machining technology for difficult-cutting materials, to improve the cutting performance of cutting tool, fine surface finish of complex shape tools using magnetic polishing technology is in high demand. This study is, therefore, discussed and compared the cutting characteristics of polished tools by the adopted various magnetic polishing moving types a point of view the cutting forces and the tool life. Moreover, the practicality of magnetic polished tools in the wide range cutting conditions is investigated. From obtained results, It is confirmed that the CW(clockwise) revolution and oscillation type as the polishing moving type is proper and magnetic polished tool shows the excellence in high cutting speed range.

• 한국정밀공학회지
• /
• 제13권4호
• /
• pp.136-142
• /
• 1996

Automatic monitoring of cutting process is one of the most important technology in machining. AE sensing technology has been applied to monitoring process and proved to be effective in detecting tool abnor- malities such as tool wear and fracture. In this experimental study. AE signals were detected from the tool holder for continuous and interrupted cutting, which obtained from changing workpice material configuration, under control of constant cutting speed from CNC lathe. From statistical and frequency analysis, the AE signals were analyzed to obtaining the characteristics of continuous and interrupted cutting conditions and tool failure. The Kurtosis values decreased but RMS voltages increased as the cutting speed increased, in both continuous and interrupted cutting. RMS voltage is suddenly increased but Kurtosis value is suddenly decreased when tool failure condition. Power spectrum density of AE signals when tool failure reaches extreme value around 0.065 cycles/ .mu. m.