• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.202-208
• /
• 2003

This study carried out a cutting experiment on Duralumin A16061-76, which is light but strong and highly anticorrosive, so recently popular as a lightweight material, by changing cutting conditions and alternating 4 insert tips, and examined the effect of each insert tip on cutting force at certain cutting conditions, the measurements of the coarseness of processed surfaces roughness, and the chip workability. The 1311owing conclusions were drawn from the results. Cutting force for cutting tool is when insert tips were alternated at each cutting condition, the cutting force of cutting tools was highest then CBN tools were use(1 next by Ceramic tools, Cermet tools, and WC tools. Therefore, WC tools are considered most suitable for cutting Duralumin A16061-T6. Surface roughness as for the coarseness of surfaces according to insert tips applied to Duralumin A16061-T6 under the cutting condition of depth of cut below 1mm, feed rate below 0.24mm/rev and cutting speed over 100m/min the coarseness of material surface roghness appeared to be finest when WC tools were used, next by Ceramic tools, Cermet tools, and CBN tools.

• 한국정밀공학회지
• /
• 제3권2호
• /
• pp.62-75
• /
• 1986

An experimental investigation of the machining characteristics such as cutt- ing resistance, surface roughness and tool wear in turning the test pieces of SM45C steel with both coated and uncoated carbide tool tips under various cutting conditions was conducted. Also a specially designed simple vibration damping device was experimentally evaluated for its effectiveness on machined surface roughness and a vibration test was conducted to confirm its ability to reduce the amplitude. Based on these tests finding, the following conclusions are made; 1. The cutting resistance($\textrm{p}_{1}$) increases as the depth of cut(d) increases at fixed feed rate(f) over the cutting speed(v) range of 43-226 m/min and p decreses about 18% average when V is increased for fixed d and f. At V= 226m/min, $\textrm{p}_{1}$/for A, C tips are about the same level but $\textrm{p}_{1}$ for B tip is 15% less than A, C tips. 2. The specific cutting resistance(Ks) at V=226 m/min was derived for A, B, C tips respectively and the value of Ks for B rip is about 20% less than A, C tips. 3. The surface roughness(Ra) improves significantly as the cutting speed(V) is increased and this effect was greater when V>100 m/min. On the other hand, Ra deteriorates as the feed rate(f) is increased and this trend was accelerated when f>0.3 mm/rev. With regard to the difference of Ra values among A, B, C tips, at V=226m/min, d=0.4mm, and f=0.31-0.61mm/rev, Ra values for B.C tips are about 17% less than tip A. 4. The experimental tool wear equations were derived for A, B, C tips and from these equations, the tool life($\textrm{T}_{\textrm{L}}$) baced on the I.S.O. criteria was calculated to be $\textrm{T}_{\textrm{L}}$<$\textrm{T}_{\textrm{LB}}$<$\textrm{T}_{\textrm{LC}}$ for both flank wear($\textrm{V}_{\textrm{B}}$) and boundary wear($\textrm{V}_{\textrm{N}}$). Hence, the coated tips are superior to the uncoated tip and tip C is considered to be the best. 5. The cutting resistance may be slightly reduced and the surface rounghness improved when the damper is used especially when V>100 m/min. Therefore this damping device is considered to be effective and practical. The experimental surface roughness equations were also derived. Based on the vibration test, it is established that the surface roughness improvement was the result of amplitude reduction made possible by the damper.

• Restorative Dentistry and Endodontics
• /
• 제39권4호
• /
• pp.276-281
• /
• 2014

Objectives: The purpose of this study was to compare the cutting efficiency of a newly developed microprojection tip and a diamond-coated tip under two different engine powers. Materials and Methods: The apical 3 mm of each root was resected, and root-end preparation was performed with upward and downward pressure using one of the ultrasonic tips, KIS-1D (Obtura Spartan) or JT-5B (B&L Biotech Ltd.). The ultrasonic engine was set to power-1 or -4. Forty teeth were randomly divided into four groups: K1 (KIS-1D / Power-1), J1 (JT-5B / Power-1), K4 (KIS-1D / Power-4), and J4 (JT-5B / Power-4). The total time required for root-end preparation was recorded. All teeth were resected and the apical parts were evaluated for the number and length of cracks using a confocal scanning micrscope. The size of the root-end cavity and the width of the remaining dentin were recorded. The data were statistically analyzed using two-way analysis of variance and a Mann-Whitney test. Results: There was no significant difference in the time required between the instrument groups, but the power-4 groups showed reduced preparation time for both instrument groups (p < 0.05). The K4 and J4 groups with a power-4 showed a significantly higher crack formation and a longer crack irrespective of the instruments. There was no significant difference in the remaining dentin thickness or any of the parameters after preparation. Conclusions: Ultrasonic tips with microprojections would be an option to substitute for the conventional ultrasonic tips with a diamond coating with the same clinical efficiency.

• 대한기계학회논문집A
• /
• 제20권12호
• /
• pp.3899-3908
• /
• 1996

In order to clarify the effects of nonmetallic inclusion contents insteels (SM45C & SCM440) on the tool life, cutting experiment was performed under various cutting conditions. Tool life, cutting force, roughness of machined surface and cutting mechanism are examined on these two kinds of steel. The following conclusions were obtained from the analysis (1) Cutting force of the steels was not affected by chemical component and nonmetallic inclusion. (2) If the rate of amount, Ca/S has a value grater than about 0.2 and addition of less amount of Al, Mn, tool wear of tips decreasesinturning. (3) It is also proved that higher contents of nonmetallic inclusion improve roughness of the surface. (4) Less amount of Ca, higher amount of S, Mn and Al improve the chip breakability.

• Advances in materials Research
• /
• 제7권2호
• /
• pp.137-148
• /
• 2018

The present paper is a contribution in characterising end milling process of AISI 52100 ball bearing steel through statistical analyses of variance (ANOVA). The latter has been performed to identify the effect of the cutting parameters on the machined surface roughness and the cutting tool life. Wear measurements have been carried on multilayer coated carbide inserts and the respective surface roughness has been recorded. Taguchi's technique has been adapted to conduct the design experiments in terms of orthogonal arrays according to the cutting parameters (cutting speed, feed rate and depth of cut), the type of coating (TiN, TiCN, TiAlN) and lubricating condition. Regression analyses have conducted to the development of simplified empirical models that can be effectively used to predict surface roughness and tool wear in the present milling process.

• 한국터널지하공간학회 논문집
• /
• 제14권5호
• /
• pp.517-528
• /
• 2012

연마재 워터젯을 이용하여 암반을 굴착하기 위해서는 노즐이 삽입되고 절삭하는 연속적 공정이 요구된다. 본 연구에서는 노즐이 삽입되기 위한 충분한 절삭 폭을 확보하기 위해 한 쌍의 연마재 워터젯 노즐을 이용하여 암석 절삭실험을 실시하였다. 한 쌍의 노즐형태와 위치에 따른 기하학적 변수에 따라 암석 절삭형상과 절삭 폭이 달라지는 것을 확인하였다. 정의된 기하학적 변수에 따라 절삭 깊이 및 폭을 측정하여 암반에 형성되는 절삭단면 형상을 분석하였다. 그 중 노즐 삽입이 가능한 기하학적 변수를 제시하고 현장적용 가능성에 대해 검증하였다.

• 한국터널지하공간학회 논문집
• /
• 제26권3호
• /
• pp.169-189
• /
• 2024

본 연구에서는 Shield TBM 터널 근접 시공으로 인한 기 존재하는 단독말뚝 및 군말뚝의 공학적 거동을 파악하기 위해 다양한 보강조건을 고려한 3차원 유한요소해석을 수행하였다. 수치해석에서는 말뚝 절단, 지반보강 및 기초판 보강을 고려하여 말뚝의 거동을 분석하였으며, 터널굴착으로 유발되는 지반침하, 말뚝두부 침하, 말뚝의 축력 및 말뚝-지반 사이 경계면에서 발생하는 전단응력을 고찰하였다. 말뚝선단이 풍화암에 지지되는 모든 말뚝에서는 전단응력의 분포가 비슷한 경향을 보였으며, 말뚝선단이 절단되는 말뚝의 경우 말뚝의 상대적 위치에 따라 인장력 혹은 압축력이 동시에 발생하는 것으로 나타났다. 또한, 말뚝선단이 풍화암에 지지된 경우 약 70%가 주면마찰력에 지지되며, 나머지 약 30%가 말뚝선단에 지지되는 것으로 분석되었다. 추가적으로 보강을 고려하지 않은 말뚝의 경우 그라우팅 보강을 실시한 말뚝에 비해 최종침하가 약 70% 크게 발생하였다. 말뚝선단 절단 및 보강조건 유무에 따라 지반 침하와 말뚝 침하가 큰 영향을 받는 것으로 조사되었으며, 본 연구를 통해 말뚝절단, 지반보강 및 기초판 보강 조건에 따른 단독말뚝 및 군말뚝의 거동에 영향을 미치는 주요인자를 심도있게 고찰하였다.

• 동력기계공학회지
• /
• 제12권3호
• /
• pp.66-71
• /
• 2008

Diamond-like-carbon (DLC) coatings could be good candidates as solid lubricants for cutting tools in dry machining of aluminum alloy. In this work, DLC thin films were produced as a friction reduction coating for WC-Co insert tip using the plasma immersion ion beam deposition (PIIED) technique. DLC coatings were also coated on $Al_2O_3$ specimens and high temperature wear tested up to $400^{\circ}C$ in dry air to observe the survivability of the DLC coating in simulated severe cutting conditions using a pin-on-disc tribotester with Hertzian contact stress of 1.3GPa. It showed reduced friction coefficients of minimum 0.02 up to $400^{\circ}C$. And cutting performance of DLC coated WC-Co insert tips to Al 6061 alloy were conducted in a high speed machining center. The main problems of built-up edge formation in aluminum machining are drastically reduced with improved surface roughness. The improvements were mainly related to the low friction coefficient of DLC to Al alloy and the anti-adhesion of Al alloy to WE due to the inertness of DLC.

• 한국기계가공학회지
• /
• 제8권4호
• /
• pp.76-82
• /
• 2009

A worm screw is widely used in a geared motor unit for motion conversion from rotation to linear motion. For mass production of a high quality worm, the current roll forming process is substituted with the milling cutter process. Since the milling cutter process enables the integration of all machining operations of worm manufacturing on a CNC(Computer Numerical Control) lathe, productivity can be remarkably improved. The tooling system for side milling cutter on the CNC lathe to improve machinability is developed. However, the runout of spindle and cutting tips are important factors to be considered for producing high quality worms because the tooling system has multiple tips. In this study, surface roughness variations accuracy according to runout was investigated in side milling cutter for worm screw. The result shows by simulation and experiment.

• 대한전자공학회논문지TE
• /
• 제39권2호
• /
• pp.29-33
• /
• 2002

수소화된 p형 Si(100)표면에 대기중에서 작동하는 주사형 터널링 현미경(scanning tunneling microscopy-STM)을 이용하여 미세구조를 제작하였다. 시료의 표면처리는 HF 용액에 1분간 담가 수소화하였다. STM의 탐침은 백금합금을 역학적인 방법으로 45$^{\circ}$로 잘라서 사용하였다. STM의 바이어스 전압을 변화시켜가며 미세구조를 제작하였다. 최적의 미세구조 선폭은 30 nm이고 이 때의 바이어스 전압은 1.7V, 터널링 전류는 1nA였다.