• Journal of Biosystems Engineering
• /
• 제22권3호
• /
• pp.289-294
• /
• 1997

The chestnut is a well-known and important forest product in Korea. The annual production of chestnut is about 100, 000tons and its cultivating area is 80, 000ha. However, the peeling process of outer and inner skins of chestnut is very difficult due to hardness and adhesiveness of chestnut skin. The peeling process of chestnut was operated by manual work and the performance of chestnut peeling machine is very low. The purpose of this study is to develope the prototype of new chestnut peeling system. The hardness of chestnuts was tested with six different drying conditions and its range was from 949$g/mm^2$ to 2, 149$g/mm^2$. The hardness of chestnuts was decresed gradually during the drying process. The chestnut peeling Process includes sorting, storage, drying, outer skin cutting, flame peeling, continuous frictional skin peeling, and inner skin cutting operation. The developed chestnut peeling system consists of outer skin cutter, flame peeler, continuous frictional skin peeler and inner skin cutter. The system can peel domestic chestnuts at 150$kg/hr$ with peeling rate of 78%.

• 한국기계가공학회지
• /
• 제11권5호
• /
• pp.29-34
• /
• 2012

This study describes the selection of optimum machining conditions for a high-hardness resin by using a large 5-axis machine. The experiments were conducted to examine the main factors that affect the surface roughness, such as the spindle speed, axial and radial depths of the cut, and pattern of the cutter path. To analyze the experiment results, the factor with the biggest impact on machining was determined using the smaller-the-better characteristic of the Taguchi method; the effectiveness of the experiment was then confirmed by verifying the selected optimum machining condition.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.448-452
• /
• 2005

Punching/blanking/shearing is among the oldest and most frequently used sheet metal forming process. We have developed the shear device for burrless cutting using the micro wire. Since the burr minimization and fine shear plane, this paper is a study on the effect of the shear angle and clearance of the cutter-cutter. And, we confirm the tendency of the shear plane. It is impossible to completely remove the burr in the shearing process. In order to minimize the burr size and fine shear plane, we have accomplished the various experiment conditions such as the shear angle and clearance. Despite the quality of shear plane is not good enough yet, it is possible to make the burr minimization and fine shear plane by the optimization of process parameters.

• 한국정밀공학회지
• /
• 제17권1호
• /
• pp.171-178
• /
• 2000

In this study, an indirect method to estimate the setup runout of a ball-end mill from cutting force signal is proposed. This runout makes cutting forces of each tooth of the milling cutter unequal. By transforming the cutting force model from time domain to frequency domain through time-convolution theorem, the magnitude and phase angle of runout can be explicitly expressed with material constants, cutting conditions, and force signal. The static setup runout can be obtained by extrapolating estimated effective runout, which is independent of feedrate but decreases linearly with increase in axial depth of cut. The setup runout estimated by slot cutting experiments, shows good agreement with the measured one.

• 한국터널지하공간학회 논문집
• /
• 제16권2호
• /
• pp.237-248
• /
• 2014

TBM의 사양을 설계하고 굴진성능을 예측할 때 실대형 선형절삭시험을 통하여 설계변수를 획득하는 것이 매우 효과적인 방법인 것으로 알려져 있다. 하지만 선형절삭시험을 위해서는 대형 시편을 획득하고 큰 하중용량의 시험을 수행하는 과정에서 상당한 비용과 노력이 소모된다는 단점이 있다. 따라서 선형절삭시험을 대체하는 경험적 예측 모델, 즉 CSM모델과 NTNU모델을 사용하여 몇 가지 지수를 산정하고 이로부터 설계변수를 추정하는 경우가 많다. 본 연구에서는 압입시험 및 세르샤 마모시험을 이용하여 TBM의 사양(추력, 토크)과 굴착에 따라 소요되는 디스크 커터의 개수를 추정하는 방법에 대하여 고찰하였다. 압입시험과 세르샤 마모시험은 TBM의 설계 변수를 추정하기 위한 유용한 시험법이나 그 활용법이 연구 되고 있지 못한 실정이다. 이 연구에서는 압입시험과 세르샤 마모시험결과를 간단한 형태의 지수형태로 도출하고 이를 선형절삭시험 및 실제 굴진자료와 비교하여 상관관계를 도출하고 이로 부터 디스크 커터의 작용력 및 수명을 예측하였다. 또한 이 일련의 계산 과정을 프로그램화 하였으며, 터널의 연장 정보, TBM의 기계정보, 구간별 암석의 물성을 입력변수로 하여 구간별 굴진율과 TBM 사양 및 운영조건, 디스크 커터의 소모개수를 예측할 수 있었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.934-938
• /
• 2000

Built-up edge affects the surface integrity of the machined surface and tool wear. Tool geometry and cutting conditions are very important factors to remove BUE. In this paper, we optimized the geometry of the metal slitting saw .1nd cutting conditions to remove BUE by the experiment. In general, the metal slitting saw is plain milling cutter with thickness less of a 3/16 inch. This is used for cutting workpiece where high dimensional accuracy and surface finish are necessary. The experiment was planned with Taguchi method that is based on the orthogonal array of design factors(coating, rake angle, number of tooth, cutting speed, feed rate). Response table was made by the value of the surface roughness, the optimized tool geometry and cutting conditions through response table could be determined. In addition. the relative effect of factors were identified by the variance analysis. filially. coating and cutting speed turned out important factors.

• 터널과지하공간
• /
• 제33권5호
• /
• pp.425-434
• /
• 2023

TBM 디스크 커터의 마모량을 실시간 계측하기 위해서는 센서를 이용해 계측을 자동화하는 것뿐만 아니라, 계측된 데이터를 후방의 정보처리시스템에 안정적으로 전송하는 것도 중요하다. 본 연구에서는 TBM 커터헤드에 설치된 센서로부터 챔버 후방에 설치된 수신기로 데이터를 무선 전송할 때 저전력 블루투스(Bluetooth Low Energy, BLE) 기술의 활용 가능성을 검토하였다. 실험실 모사 실험을 통해 송신기의 신호강도, 송신기와 수신기 사이의 거리, 챔버 공간에 채워진 물질의 종류에 따라 변화하는 수신기의 신호 수신 강도(Received Signal Strength Index, RSSI)의 특성을 분석하였다. 송신기의 신호강도를 0 dBm 이상으로 설정하면 실험에서 고려한 모든 이격거리 조건과 챔버의 상태 조건에서 데이터를 무선 전송할 수 있었다.

• Journal of Biosystems Engineering
• /
• 제30권3호
• /
• pp.161-165
• /
• 2005

In this study, peeling test of the Altari radish on kimchi pre-processing system for mechanization was performed with the longitudinal plane peeling type with wider cutting blade than that of the peeled chip's. To determine the optimum cutter shape to match this plane peeling type, the peeling tests depending on variable cutting speed, rake angle and blade angle using the blade with thickness as 2 m and width as 50mm were performed, and the patterns of the peeled chips and peeling resistances were investigated. As the result of the tests, the rake angle of the blade with clean peeled surface of the Altari radish was over $45^{\circ}$, and the blade angle and rake angle with the minimum peeling resistance was $20^{\circ}\;and\;60^{\circ}$, respectively. The optimum peeling conditions were; the peeling speed 0.2m/s, blade angle $20^{\circ}$ and the rake angle $60^{\circ}$, and the peeling resistance of each blade was 15 N.

• 한국공작기계학회논문집
• /
• 제11권6호
• /
• pp.1-9
• /
• 2002

This study describes the geometric characteristics and the 5-axis machining method in order to make end mill cutter coming with insert tips. End mill geometry is consisted of flute part and insert tip part. Flute part modeled by using ruled surfaces with constant helix angle, and insert tip part modeled by rectangular planes containing tapped hole of specified direction in its center. In this study, the modeled insert tip part considered both of a radial rake angle and a axial rake angle, because they were important cutting conditions. In order to machining the virtual end mill defined from geometric characteristics, we programmed a special software to machining the end mill considered in this study. This software can generate NC-codes about following processes, end milling or ball end milling of flute part end milling of rectangular plane, centering of hole, drilling of hole, and tapping of hole. Ant sampled end mills were modeled and machined on 5-axis CNC machining center with two index tables. Since machined end mills were very agreeable to designed end mills, we saw that the method proposed in this study can be very useful for manufacturing of end mill body with insert tip.

• 한국공작기계학회논문집
• /
• 제17권1호
• /
• pp.144-149
• /
• 2008

This study presents the selection of cutting conditions in high speed pipe cutting machine for the better quality. A high speed pipe cutting machine which uses a rotary knife can make good quality products in short time. But, the machine is much sensitive by cutting conditions because of the complicated mechanism. In this reason, many experiments for cutting condition selection are necessary to improve quality of production. This study carried out cutting experiments with the three factors that are cutting RPM, cutting force and pooling force. 2-dimensional profile measuring instrument is used to measure which is represented by ${\Delta}h$, a sum of burr and collapse height. The effects of factors are analyzed by using MINITAB, the commercial software.