• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.1369-1375
• /
• 2006

This study analyzes stability and the reason of slope failure about cut slope on stony mountain in Acheondong, Guri and suggests the reasonal reinforce method. Based on the results of the subsurface exploration, laboratory tests, and the numerical analysis of finite element method, the potentials of plane and wedge failure are highly estimated. The safety factor was 1.2 under dry and 1.06 wet condition. The most proper reinforce method to raise the safety factor more than 1.5 was the way to control displacement by using step retaining wall, earth anchor, wire mesh, and rock anchor.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.33 no.1
• /
• pp.9-16
• /
• 1984

This paper describes the minimum cost expansion planning which is based on the economical aspect under the various conditions on the power system expansion planning. It presents not only linear cost characteristics analysis but also stepwise cost characteristics analysis which satisfies practical condition in the power system. The latter analysis must be handled by integer programming (IP), because the relation between the cost and the capacity has stepwise characteristics. In order to proceed the latter analysis, the solving procedure is illustrated in detais by using branch and bound method which includes the network flow theory and maximum flow-minimum cut theorem.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.6_3
• /
• pp.1197-1204
• /
• 2023

Ti-alloy, a high-strength alloy material among the materials used in aircraft that are trending toward lighter weight, is classified as a difficult-to-cut material that requires a lot of energy for cutting. Cutting in a high-temperature environment is considered one means of making this possible, and various studies have been conducted on it. In particular, research on LAM (Laser Assisted Machining (LAM)), which utilizes laser heating of the cutting area, is being actively conducted. Before processing of the milling cutter begins, the temperature is raised locally by the laser irradiated through the laser head carrier, and the resistance during milling is reduced. Therefore, in this paper, in order to derive such conditions, we performed heat transfer analysis according to transfer conditions and compared it with actually applied test data to use it to establish appropriate processing conditions.

• Journal of Korean Academy of Fundamentals of Nursing
• /
• v.13 no.2
• /
• pp.190-199
• /
• 2006

Purpose: To provide basic data and to identify the risk of pressure ulcers among neurological patients in ICU. Method: The participants in the study were on 78 neurological patients in the ICU of 3 hospitals. Data were collected every other day from 24 hours after admission, for up to 40 days or until discharge. The total period of data collection was 3 months. The risk assessment scales used for pressure ulcer were the Cubbin & Jackson(1991) scale and the National Pressure Ulcer Advisory Panel(1989) skin assessment tool. Results: There was a significant relationship between having a pressure ulcers and weight, skin condition, mental status, respiration, hygiene and hemodynamic status compared to not having a pressure ulcer. The incidence rate of the pressure ulcer was 28.2%(n=22). Of these patients the mean number of hospitalization days until pressure ulcer development was 5.2 days. The most common pressure ulcer site was the coccyx(39.3%). Based on a cut-off point of 24, 9 patients with risk scores <24 on admission also showed risk score for development of pressure ulcers, 10 patients with pressure ulcer scores ${\geq}24$ were older, hospitalized for a longer time, had low serum albumin, low hemoglobin, diabetes mellitus and surgery. Conclusion: In order to make the Cubbin & Jackson risk assessment scales more useful, there is a need to determine the reliability of the upper cut-off point 24. The result also showed a need to assess other risk factors and for early identification of at-risk patients in order to provide preventive care from admission to discharge.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.7
• /
• pp.94-100
• /
• 1999

This study adopted the ultra precision machining system which was composed of an air bearing spindle, a granite bed, air pad and a linear feeding mechanism. It also applied the cutting experiment on the aluminum alloy. To evaluate the safety of high speed machining, we examined the surface roughness according to the changes of cutting speed and obtained the speed limit. This paper also studied the effect of cutting condition such as feed rates and depths of cut on the surface roughness within the speed limit. This provided practical information regarding ultra precision machining.

• Journal of Chest Surgery
• /
• v.16 no.1
• /
• pp.34-39
• /
• 1983

The syndrome of anomalous muscle bundle dividing the right ventricle into two pressure chambers has been described by many authors. The malformation should not be confused with tetralogy of Fallot itself because the obstructive hypertrophic bands are usually proximal to the right ventricular infundibulum. One case [11 years old male] of double chambered right ventricle due to aberrant muscle bundle with intact ventricular septum is presented. The pressure gradient was 68 mmHg between inflow and outflow tracts of right ventricle on cardiac catheterization. On opening the right ventricle, there noted stenosis of outflow tract by infundibular membrane, hypertrophied anomalous muscle bundle, thickened moderator band & hypertrophied anterior papillary muscle. Open heart surgery was carried out with the aid of extracorporeal support, Anomalous muscle bundle [1.0 cm x 4.0 cm] and infundibular membrane were resected safely. The hypertrophied moderator band was cut at mid-portion and anterior papillary muscle was split vertically. The postoperative course was uneventful and discharged in good condition 2 weeks later.

• Wind and Structures
• /
• v.30 no.3
• /
• pp.245-260
• /
• 2020

Wind load and responses are the major factors which govern the design norms of tall buildings. Corner modification is one of the most commonly used minor shape modification measure which significantly reduces the wind load and responses. This study presents a comparison of wind load and pressure distribution on different corner modified (chamfered and rounded) Y plan shaped buildings. The numerical study is done by ANSYS CFX. Two turbulence models, k-epsilon and Shear Stress Transport (SST), are used in the simulation of the building and the data are compared with the previous experimental results in a similar flow condition. The variation of the flow patterns, distribution of pressure over the surfaces, force and moment coefficients are evaluated and the results are represented graphically to understand the extent of nonconformities due to corner modifications. Rounded corner shape is proving out to be more efficient in comparing to chamfered corner for wind load reduction. The maximum reduction in the maximum force and moment coefficient is about 21.1% and 19.2% for 50% rounded corner cut.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.6
• /
• pp.44-49
• /
• 2003

To obtain the surface roughness with range from 10nm to 1nm we need the study of ultra-precision machine, cutting condition, and materials. In this paper, the optimal cutting conditions for getting mirror surface of aluminum alloy have been examined experimentally by using ultra-precision turning machine and sing1e crystal diamond tool. In generally, the cutting conditions such as feed rate and depth of cut have effect on the surface roughness in ultra-precision turning. The result of surface roughness was measured by the ZYGO New View 200. Therefore, The surface roughness and cutting conditions has been clarified. The smooth surface of aluminum alloy less than 1nm RMS, 1nm Rmax can be obtained by the ultra-precision cutting.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.5
• /
• pp.35-43
• /
• 2007

Laser welding of metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research works is to investigate the influence of the process parameters, such as the welding for metals with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the butt welding, the welding quality of the cut section, stain-stress behavior and the hardness of the welded part are investigated. From the results of the investigation, it has been shown that the optimal welding condition without defects in the vicinity of the welded area and with a good welding quality is 1325W of the laser power, and 1.4m/min of laser welding speed.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.8
• /
• pp.100-105
• /
• 1999

This work analyses the effects of electrical conductivities of dielectric and cobalt amount on output parameters such as metal removal rate and the surface roughness value of cemented carbides cut by wire electrical discharge machining(W-EDM). Especially, the cracking behaviour of W-EDM machined surface and optimal machining condition of three kinds of cemented carbides, which have different chemical composition of tungsten carbide and cobalt are also tested. Experimental result shows that increases in cobalt content and electrical conductivity of the dielectric affect the metal removal rate and substantially worsen the final surface quality as a greater quantity of solidified metal deposits on the eroded surface.