• Journal of Forest and Environmental Science
• /
• v.30 no.1
• /
• pp.71-75
• /
• 2014

Forest roads failure is one of the most common problems caused by heavy rainfalls. This study investigated the characteristics on stabilization measures installed for cutting slopes failure of forest road resulted from heavy rainfalls. Three primary factors (slope length, slope gradient, soil type) affecting cutting slope failure were considered and stabilization measures were classified into two types (A type: wooden fence, vegetation sandbag, stone masonry; B type: wire cylinder, gabion, concrete retaining wall) through discriminant analysis based on their capacity of resistance to slope failure. Results showed that A type was mainly installed in such conditions as cut slope <8 m, cut slope gradient $30-40^{\circ}$ and soil type with soil while B type occurred in locational conditions as cut slope length >8 m, cut slope gradient < $30^{\circ}$ and > $30^{\circ}$, and soil type of gravelly soil and rock.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.722-726
• /
• 2010

Inventory survey is process collecting data about cut slope. It's different from inspection. It contains not only basic information about cut slope, especially location, GPS positioning, height, length, weathering, joint direction, water conditions but also level of danger and damage. Collected data are being used get at status about cut slope along national roads. And It helps judging about priority of detailed investigation. According to results of analysis, we found better method about maintenance of cut slope. Later on, if inventory research is finished, we will understand characteristics of collapse slopes.

• Asian-Australasian Journal of Animal Sciences
• /
• v.4 no.1
• /
• pp.7-14
• /
• 1991

An experiment was carried out to investigate the effect of change in length of hay offered on eating and rumination behaviour in sheep using three types of hay diets (L: long, M: 8.0-cm cut, S: 1.2-cm cut) and 3 Japanese Corriedale wethers, and the experiment was designed as $3{\times}3$ latine square. The time spent eating per 100 g hay was significantly shorter with long (L) hay (p < 0.05) than with chopped (M and S) hay, and therefore, the eating rate (g D.M./min.) was significantly higher in the former (p < 0.05) than in the latter. Rumination appearance (the lag time after eating) tended to be longer with long hay than with chopped hay, but not significantly (p > 0.05). Daily time spent ruminating, the actual chewing time and daily number of chews tended to be more in feeding long hay than in feeding chopped hay, but not significantly. Daily number of rumination periods was significantly more with long hay (p < 0.01) than with chopped hay. Cyclic rate tended to be longer with long hay than with chopped hay, in particular, the difference in values between long hay and 8.0-cm cut hay was significant statistically (p < 0.01). The rumination index (time spent ruminating/100 g D.M, eaten) tended to be higher with long hay than with chopped hay, and the difference in values between long hay and 1.2-cm cut hay was significant statistically (p < 0.05). Bolus time was significantly longer with long hay (p < 0.01) than that with 8.0-cm cut hay. The circadian pattern of ruminating time was not changed by the changes in length of hay eaten.

• Horticultural Science & Technology
• /
• v.30 no.1
• /
• pp.13-20
• /
• 2012

This study was carried out to examine the effect of cutting condition on the growth of rooted cuttings and their subsequent growth of cut flower in plug cutting of Dendranthema grandiflorum 'Baekma'. The more leaves were attached to the cutting, the higher shoot growth of rooted cutting was observed. Cutting with two to six leaves was effective in shoot growth and rooting than any other treatment. Shoot growth of rooted cutting was not affected by cutting length, but rooting was better in 5 to 7 cm long cutting. Shoot growth and rooting of rooted cutting was promoted by increasing the cutting diameter, and rooting was better in 3.6-4.2 mm thick cutting than 3.1 mm thick cutting. As the treating concentration of NAA increased, shoot growth was inhibited and root length shortened in rooted cutting. Soaking with $100mg{\cdot}L^{-1}$ ${\alpha}$-naphtalene acetic acid (NAA) for 1 h was effective in shoot growth and rooting. Root growth such as root number, root length, and root weight was better in rooting medium mixed with 2:2 of peatmoss:perlite than the other treatments. When rooted cutting produced from cutting with four or six leaves was planted, better length, weight, and leaf number of cut flower was observed. In rooted cutting produced with 7-9 cm long cutting, growth of cut flower such as length, weight, and ray flower number was more effective than the others. Therefore, it is recommended that the 7 cm long and 3.6 mm thick cutting with four to six leaves is used to improve their rooting and subsequent growth of cut flower in plug cutting of Dendranthema grandiflorum 'Baekma'.

• Geomechanics and Engineering
• /
• v.38 no.4
• /
• pp.421-437
• /
• 2024

The soil nailing method entails the utilisation of nails to reinforce and stabilise a zone of soil mass. This is widely used for various applications due to its effective performance under various loading conditions. The seismic response of 6m high vertical soil-nailed cut in various site classes under dynamic excitations has been investigated in this study considering various lengths and inclinations of nails. The influence of frequency content of dynamic excitation on the response of structure has been assessed through finite element analysis using time history data of three different earthquakes. The seismic stability of the nailed cut in retaining soil in various sites under El Centro, Kobe and Trinidad earthquake ground motion is evaluated based on maximum acceleration response, maximum horizontal deformation, earth pressure distribution on the wall and maximum axial force mobilised in nails. The optimum nail inclination is identified as 15° and a minimum nail length ratio of 0.7 is essential for a stable vertical cut under dynamic excitations.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.2
• /
• pp.143-150
• /
• 2000

In this paper, an optimum size for the inset cut feed of microstrip antennas has been determined by using the finite-difference time domain method. At first, the return losses of microstrip antennas having various shapes and types of the inset cut feeds have been computed numerically for a given frequency and a substrate. Then an optimum size of the inset cut feed has been determined by iterative computation procedure for a given condition. It was found that the optimum width of the inset cut feed is about 0.42 times of the width of 50Ω feed line and the optimum length of the inset cut feed is about 0.36 times of the length of the antenna patch. These results are proved by the experimental data obtained from the measurements of many fabricated antennas. It was also found that the optimum size of the inset cut feed is independent on the frequency, the height and the dielectric constant of the antennal substrate.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.11 no.4
• /
• pp.419-425
• /
• 2009

Recently, the number of shallow tunnel construction increases to improve the structural safety and environment-friendliness. In Semi-Cut and Cover Method, ground is excavated to the crown arch level and braced rib arch is set to backfill before the excavation of lower face. Semi-Cut and Cover Method is proposed to solve the problems occurred by the conventional Cut and Cover Method, such as unstability, high-cost and the large cutting slope to be reinforced. In this paper, the behaviors of Braced Rib Arch in shallow tunnel excavated by semi-cut and cover method was studied. Model tests in 1:10 Scale were performed in real construction sequences. The distance between supports of rib arch was 1.8 m and the length of spacer was 1.0 m. the size of test pit was 4.0 m (width)$\times$3.3 m (length) 4.0 m (height) in dimension. Tests results show that backfill load acting on arch was smaller than that in the conventional Open-Cut Method.

• International Journal of CAD/CAM
• /
• v.6 no.1
• /
• pp.167-172
• /
• 2006

Recently, wire-EDM became a necessity for many engineering applications, particularly in the dies making. No-Core cut process is helpful for operations in which falling slug can jam the machine or wire. In this paper a proposed CAM system (called NCPP) is introduced, to overcome the limitations of the existing CAM systems in the machining of No-Core cut. The proposed CAM system (NCPP) provides pocketing of No-core cut and optimal selection of the position of starting hole (wire threading point), to minimize toolpath length. It was written for data exchange between CAD-CAM-CNC machines. This data model will become part of the ISO (Data model for Computerized Numerical Controllers) international standard. The NCPP system has been implemented in Visual C++. Many examples are used to illustrate NCPP system. The results show that, NCPP saves the machining time by significant value. This value depends on the shape and complexity of the workpiece that is being cut.

• Journal of Korean Society of Forest Science
• /
• v.113 no.3
• /
• pp.361-371
• /
• 2024

This study was conducted to develop models of the xylem volume utilization rate and merchantable log utility rate of the Japanese larch (Larix kaempferi [Lamb.] Carrière), a major commercial species in South Korea. To develop these models, models were fitted together for the xylem volume utilization rate and merchantable log utility rate to the total stem volume. Data on the logs bucked by cut-to-length usage in the forestry field were used for modeling, and the tree diameter at breast height (DBH) and small-end diameter of the last log were used as major predictor variables. Considering the difference in the bucking rate between all logs and solely long-length logs, the models for merchantable log utility rate were classified into two types: short- and long-length logs as well as only long-length logs. Consequently, the models were significantly developed, and the predicted values showed high accuracy within the range of observed values. The tables for bucking rate by cut-to-length log usage were finally provided by applying the models of the xylem volume utilization rate and merchantable log utility rate. Because the bucking rate for all logs and long-length logs can be easily calculated with the easy-to-use DBH and the required small-end diameter of the last log, the developed models are highly expected to be applicable for predicting the timber assortment using the cut-to-length log usage.

• Transactions of Materials Processing
• /
• v.15 no.4 s.85
• /
• pp.311-318
• /
• 2006

One of the most important quality problems in flat plate leveled from hot rolled coils in cut-to-Iength lines is bowing and cambering when they are cut in small width parts. It is verified analytically and experimentally that residual stress remained in plate is th ε source of the problem. In order to produce low residual stress flat plate from hot rolled coils, the proper conditions of leveling are studied and two things are implemented. One is proper plastic deformation area ratio to reduce residual stress within customer requirement by applying suitable plastic deformation and maintain leveling load within structural strength limit of leveler. The other is maintaining uniform plastic deformation along the width of the plate during leveling. Customer requirement for residual stress is met by applying above 70% of plastic deformation area ratio and uniform deformation along width of coil by adjusting back up rolls according to deformation analysis of work roll and back up roll assembly and leveling tests.