• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.682-684
• /
• 2002

There is much room for consideration that the magnet design of UTM. When the vehicle runs 60mR curved line on test track, the ratio of cross section area changed to cross the magnet pole and rail. The ratio is reduced about 20% of the total magnet on one bogie. Therefor, magnet current is increased about 3.5A to maintain constant air gap. This paper suggest to margin of the magent design is 1.1 rather than rated levitation force.

• Journal of the Korean Society of Safety
• /
• v.32 no.5
• /
• pp.41-46
• /
• 2017

The coefficient of derailment and the rate of wheel load reduction were used as the index of train running safety that was directly affected the train derailment safety. In aspects of track, the train running safety depends on the complex interaction between wheel and rail, and the track-vehicle conditions (i.e., the curvature, cant, track system, vehicle speed and the operation conditions, etc). In this study, the relationship between the train running safety and the track curvature and vehicle speed for direct fixation concrete tracks currently employed in Korean light rapid transit was assessed by performing field tests using actual vehicles running along the service lines. The measured dynamic wheel load, lateral wheel load and lateral displacement of rail head were measured for same train running on four tested tracks under real conditions, which included curved and tangent tracks placed on the tunnel and bridge, thus increasing the train speed by approximately maximum design speed of each test site. Therefore, the measured dynamic track response was applied to the running safety analysis in order to evaluate the coefficient of derailment, the rate of wheel load reduction and the track gauge widening at each test site, and compare with the corresponding Korean train running safety standard. As the results, the lateral track response of direct fixation concrete track appeared to increase with the decreased track curvature; therefore, it was inferred that the track curvature directly affected the train running safety.

• Proceedings of the KSR Conference
• /
• 2006.05b
• /
• pp.388-399
• /
• 2006

• Journal of the Korean Society for Railway
• /
• v.11 no.1
• /
• pp.33-38
• /
• 2008

To reduce the cost and time of transport in Eurasian railroad networks such as TKR, TCR and TSR owing to the problem of different track gauges (narrow/standard/broad gauge), it is important to develop the gauge-adjustable wheelset system to adapt easily to these gauges. Moreover, freight trains having the gauge-adjustable wheelsets should be passing various curved tracks in railroad networks. Therefore, to assure the safety of the gauge-adjustment whellset system, it is necessary to evaluate integrity of locking parts in the system using stress analysis. This study is focused on analyzing contact stress of locking parts by using FEA(finite element analysis) simulation during the gauge changeover operation and freight trains' service in the curved track, respectively.

• The KIPS Transactions:PartB
• /
• v.13B no.3 s.106
• /
• pp.239-244
• /
• 2006

In this paper, we present a snake-based scheme for contour tracking of objects in stereo image sequences. We address the problem by managing the insertion of new points and deletion of unnecessary points to better describe and track the object's boundary. In particular, our method uses more points in highly curved parts of the contour, and fewer points in less curved parts. The proposed algorithm can successfully define the contour of the object, and can track the contour in complex images. Furthermore, we tested our algorithm in the presence of partial object occlusion. Performance of the proposed algorithm has been verified by simulation.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.7
• /
• pp.597-602
• /
• 2015

In this paper, we studied the steering performance of wheelset with primary suspension characteristics of railway vehicle. We carry out dynamic analysis and experimental study for the vehicle models which are different primary suspension characteristics. The steering angle of a vehicle model (Case 1) operating in domestic subway lines is insufficient compared with an objective steering angle for curved track. And the steering angle of a vehicle model (Case 2) with improved self-steering performance of wheelset is a little improved compare to previous vehicle model. But also Case 2 model is still insufficient compared with an objective steering angle and has its limit in steering performance. So to overcome this limit of steering performance of passive type railway vehicle, an active steering technology is being developed. In case of vehicle model with active steering system, the steering performance is improved remarkably compared to passive type vehicle model.

• International Journal of Railway
• /
• v.5 no.2
• /
• pp.93-101
• /
• 2012

Owing to the lightening of railway vehicles and increased operation speeds, the reduction of running safety in the presence of crosswind is becoming an important problem. In particular, the running safety tends to decrease when vehicles run on curved track. When a crosswind acts on a vehicle negotiating a curve from the outer side, flange climbing can occur. In this study, a full-vehicle model was constructed using the multi-body simulation software SIMPACK, and a simulation of a bogie vehicle with two-axle trucks negotiating a curve was carried out to examine the running safety under the condition where a crosswind acts on the vehicle from the outer side of the curve. As a result, it was verified that the derailment coefficient of the first wheelset becomes large in the exit transition curve and the coefficient of the third wheelset does in the entrance transition curve, and this trend becomes pronounced at low operation speeds in the presence of a stronger crosswind. It was also shown that the critical derailment coefficients obtained by modified Nadal's formula considering the effect of attack angle become close to the actual derailment coefficients at the timing that flange climbing occurs.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1546-1553
• /
• 2005

In this study, geotextiles was applied on the selected track-bed, which is relatively economical and efficient way to prevent the problem of mud-pumping and settlement. Field testing sections from Mock-haeng to Dong-ryang in the Chung-buk lines in Korea were selected to investigate the state of track and roadbed. And three places were chosen among 1,700 spots where mud-pumping was frequently occurred and maintenance required. At the curved section with radius of 500m between Mock-haeng and Dong-ryang, we divided this testing site into 5 section and 4 different types of geotextile were installed and left the last section with no reinforcement. Total length of the test site was 200m and individual length of each site was 40 m. In order to understand the state and the strength of prepared roadbed, stiffness and physical properties of the roadbed soil were evaluated and analyzed. Also, after the installation, mud-pumping, settlement of elastic or plastic sleeper, failure of track, wheel-loads, lateral force and earth pressures were investigated.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.1232-1240
• /
• 2001

In this study. a computer simulation of the Korean High Speed Prototype Test Train was performed to investigate the dynamic behavior(running stability. safety and comfort) in detail design process. The simulation model which was prepared by ADAMS/Rail V10.l consists of power car and middle car assembly (2 motorized cars ＋ 3 trailer cars). The nonlinear analysis takes into account the full vehicle model including wheel/rail contact and the influence of disturbed track. Throughout the dynamic calculation of KHST on the straight and the curved track. accelerations in car body. ride comforts and wheel rail forces were investigated.

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.82-90
• /
• 2003

The advance in technology of the CWR in Korea has led the establishment of the CWR on the sharp curve (i.e. less than R=600m). As thermit welding used in the sharp-curved construction site is carried out on the curve track, it is difficult to adjust a curve shape accurately and these difficulties have occurred in a number of cases. Therefore, in this study, the lateral buckling analysis of CWR track was carried out considering the actual ballast resistance force. In addition, the cant and vertical resistance force in ballast was considered in order to predict the initial behaviour of bucking in track under the more accurate method.