• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.11
• /
• pp.1706-1712
• /
• 2012

The Beta-ray absorption method (BAM) gives a good solution for measuring the mass concentration of atmospheric particles(PM10 and PM2.5). To determine particular matters (PM) concentration, a ratio of the number of detected beta-ray intensity passing through the clean filter and the dust-sampled filter is used. These intensity data measured in air pollution monitoring such as PM10 and PM2.5 usually contained the additive noise(thermal noise, power supply noise and etc.). Therefore, the estimation performance of mass concentration can be deteriorated by these noises. In this paper, we present a new noise reduction method that is essentially required to develope an automatic continuous PM monitoring system using beta-ray absorption method. By combining the block data averaging technique and curve fitting, in the proposed method, the additive noise can be reduced in the measured data. To evaluate the performance of the proposed method, computer simulations were performed with computer generated signals as the input.

• Journal of Biomedical Engineering Research
• /
• v.35 no.6
• /
• pp.227-233
• /
• 2014

In this paper, to quantitatively evaluate the degree of rehabilitation for the disabled of unilateral lower extremity, we compared the EMG pattern of normal and simulated abnormal gait. The EMG signal was measured at a rate of 1 kHz on the quadriceps and biceps femoris, the pressure sensor was attached to the sole in order to distinguish the gait cycle. Integrated EMG (IEMG) was obtained by the gait cycle, and classified four patterns that were the normal gait pattern, amplitude decrease pattern, reversed pattern, and irregular pattern. For comparison of the patterns, a curve fitting was performed using the trigonometric functions. The result of curve fitting, the method using a variable A that corresponds to the amplitude of the regression curve was able to distinguish the reverse pattern and remaining pattern. The coefficient of determination ($R^2$) representing coincidence of the pattern of the regression curve and EMG was confirmed the biggest value at the normal gait. Therefore, the degree of normal gait can be confirmed using the coefficient of determination. This results show that it is possible to quantitatively confirm the degree of unilateral lower extremity disabled rehabilitation, and it will be contributed to the study of efficient rehabilitation methods by objective analysis.

• International Journal of CAD/CAM
• /
• v.12 no.1
• /
• pp.9-19
• /
• 2012

Generation of optimum planar B-spline curve in terms of minimum deviation and required fairness to approximate a target shape defined by a strip-shaped unorganized 2D point cloud is studied. It is proposed to use the location of control points as variables within the geometric optimization framework of point distance minimization. An adaptive simulated annealing heuristic optimization algorithm is developed to iteratively update an initial approximate curve towards the target shape. The new implementation comprises an adaptive cooling procedure in which the temperature change is adaptively dependent on the objective function evolution. It is shown that the proposed method results in an improved convergence speed when compared to the standard simulated annealing method. A couple of examples are included to show the applicability of the proposed method in the surface model reconstruction directly from point cloud data.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.8 no.5
• /
• pp.45-50
• /
• 1998

This paper presents the process generating the 3-dimensional free f o r m hull form by using an ASMOD(Adaptive Spline Modeling of Observation Data) and a hybrid curve approximation. For example, we apply an ASMOD to the generation of a SAC(Sectiona1 Area Curve) in an initial hull form design. That is, we define SACS of real ships as B-spline curves by a hybrid curve approximation (which is the combination method of a B-spline fitting method and a genetic algorithm) and accumulate a database of control points. Then we let ASMOD learn from the correlation of principal dimensions with control points and make the ASMOD model for SAC generation. Identically, we apply an ASMOD to the generation of other hull form characteristic curves - design waterline curve, bottom tangent line, center profile line. Conclus~onally we can generate a design hull form from these hull form characteristic curves.

• Journal of Power Electronics
• /
• v.19 no.6
• /
• pp.1429-1439
• /
• 2019

Buck-Boost LLC (BBLLC) converters based on a PWM + phase control strategy are good candidates for high efficiency, high power density and wide input range applications. Nevertheless, they suffer from large computational complexity when it comes to calculating the optimal phase for ZVS of all the switches. In this paper, a method is proposed for a microcontroller unit (MCU) to calculate the optimal phase quickly and accurately. Firstly, a 2-D lookup table of the phase is established with an index of the input voltage and output current. Then, a bilinear interpolation method is applied to improve the accuracy. Meanwhile, simplification of the phase equation is presented to reduce the computational complexity. When compared with conventional curve-fitting and LUT methods, the proposed method makes the best tradeoff among the accuracy of the optimal phase, the computation time and the memory consumption of the MCU. Finally, A 350V-420V input, 24V/30A output experimental prototype is built to verify the proposed method. The efficiency can be improved by 1% when compared with the LUT method, and the computation time can be reduced by 13.5% when compared with the curve-fitting method.

• Korean Journal of Optics and Photonics
• /
• v.33 no.6
• /
• pp.310-316
• /
• 2022

In this paper, the difference in modulation transfer function (MTF) results according to the change in the angle of a slant target when measuring a presampled MTF was confirmed, and the difference was reduced by fitting the edge spread function graph obtained to reduce the error by the target's rotation. Due to the feature of the presampled MTF method, the spatial frequency changed due to the sensor's projected intensity being changed by the target's rotation, and it was confirmed that the difference in the MTF value occurred depending on the rotation angle of the target. In this paper, the MTF was calculated after fitting only one column of the acquired image. It was confirmed that the rotation error is smaller compared to the case of the presampled MTF method and this fitting method can be applied to a scene that contains various target angles, such as auto-focusing using the MTF.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.2 no.4
• /
• pp.17-27
• /
• 2003

This paper presents the channel estimation method with STBC applied to IEEE802.11a. Tenacious channel estimation method for OFDM system, that generally uses STTC, has been presented once and massive amount of calculation was needed However, regarding this paper, the amount of calculation can be reduced by using Curve Fitting, and channel tracking performance improvement can be achieved Based on the estimation method, computer simulation was done for the performance analysis and delay spread Doppler frequency and many other group sizes and numbers were considered As a result of the testing, we found out that Doppler frequency deviation effects equally as frequency offset. Also compared to the existing technique, channel estimated performance confirmed that have 0.9dB SNR improvement than old method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.6
• /
• pp.471-480
• /
• 2022

Inductive power transfer (IPT) is an attractive power transmission solution that is already used in many applications. In the IPT system, optimal coil design is essential to achieve high power efficiency, but the effective design method is yet to be investigated. The inductance formula and finite element method (FEM) are popular means to link the coil geometric parameters and circuit parameters; however, the former lacks generality and accuracy, and the latter consumes much computation time. This study proposes a novel coil design method to achieve speed and generality without much loss of accuracy. By introducing one-turn permeance simulation in each FEM phase combined with curve fitting and optimization by MATLAB in the efficiency calculation phase, the iteration number of FEM can be considerably reduced, and the generality can be retained. The proposed method is verified through a 100 W IPT system experiment.

• Journal of Computational Design and Engineering
• /
• v.2 no.4
• /
• pp.218-232
• /
• 2015

Piecewise linear (G01-based) tool paths generated by CAM systems lack $G_1$ and $G_2$ continuity. The discontinuity causes vibration and unnecessary hesitation during machining. To ensure efficient high-speed machining, a method to improve the continuity of the tool paths is required, such as B-spline fitting that approximates G01 paths with B-spline curves. Conventional B-spline fitting approaches cannot be directly used for tool path B-spline fitting, because they have shortages such as numerical instability, lack of chord error constraint, and lack of assurance of a usable result. Progressive and Iterative Approximation for Least Squares (LSPIA) is an efficient method for data fitting that solves the numerical instability problem. However, it does not consider chord errors and needs more work to ensure ironclad results for commercial applications. In this paper, we use LSPIA method incorporating Energy term (ELSPIA) to avoid the numerical instability, and lower chord errors by using stretching energy term. We implement several algorithm improvements, including (1) an improved technique for initial control point determination over Dominant Point Method, (2) an algorithm that updates foot point parameters as needed, (3) analysis of the degrees of freedom of control points to insert new control points only when needed, (4) chord error refinement using a similar ELSPIA method with the above enhancements. The proposed approach can generate a shape-preserving B-spline curve. Experiments with data analysis and machining tests are presented for verification of quality and efficiency. Comparisons with other known solutions are included to evaluate the worthiness of the proposed solution.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.9
• /
• pp.1232-1238
• /
• 2018

This paper proposes methods for improving mass spectral resolution for a gas chromatograph mass spectrometer. The slope signs of the 1st and 2nd fitting functions for the ion signal block of each mass index are obtained, and the unnecessary element signals in the ion signal block are removed. The spectrum can be obtained by obtaining the second-order fitting function of the reconstructed ion signal block using only the effective ion signals. In addition, the resolution of the mass spectrum can be improved by correcting the error caused by the shift of the spectral peak position. To verify the performance of the proposed methods, computer simulations were performed using the actual ion signals obtained from the GC-MS system under development. Simulation results show that the proposed method is valid.