• Journal of the Korea Furniture Society
• /
• v.10 no.2
• /
• pp.73-78
• /
• 1999

This paper describes the relationship between the bending strength properties of sloped finger-jointed woods and the acoustic emissions(AEs) generated during the test. Rhus verniciflua pieces were cut in sloped-finger types and glued with three kinds of adhesives(polyvinyl acetate, polyvinyl-acryl acetate and oilic urethane resin). The slope ratios of finger joints were 0, 1.0, 1.5, and 2.0. The AE cumulative event count and cumulative count were measured during the bending test. The results were as follows: The lower the bending strength(load) was, the generation time of AE event count got and the higher the increasing rate of AE event count became in the sloped finger-jointed specimens bonded with polyvinyl acetate, polyvinyl-acryl acetate oilic urethane resin adhesives. Therefore, the slope from load-AE cumulative event count was very steep. The patterns of AE event count and count were very similar. The relationship between the MOR and the AE parameter from load and AE cumulatve event count in the early stage of the sloped finger-jointed specimens bonded with polyvinyl acetate, polyvinyl-acryl and oilic urethane resin adhesives was much greater than that between the MOE and the MOR. Therefore, the AE signals obtained during bending test are useful for estimating the strength of sloped finger-jointed Rhus verniciflua specimens.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.1
• /
• pp.30-36
• /
• 1999

This paper describes the relationship between the bending strength properties of sloped finger-jointed woods and the acoustic emissions (AEs) generated during the test. Pinus densiflora pieces were cut in sloped-finger types and glued with four kinds of adhesives (polyvinyl acetate, polyvinyl-aeryl, oilic urethane and resorcinol-phenol resin). The results were as follows: The lower the bending strength(load) was, the earlier the generation time of AE event count got and the higher the increasing rate of AE event count became in the sloped finger-jointed specimens bonded with polyvinyl acetate and oilic urethane resin adhesives. Therefore, the slope from load-AE cumulative event count curve was very steep. The AE event count for resorcinol-phenol resin adhesive obtained even from low load level was abundant. The AE event count continuously increased as load increased and the event count was much more than one in the other conditions. The slope from load-AE cumulative event count curve was very gentle compared with other conditions. The patterns of AE event count and count were very similar. The relationship between the MOR and the AE parameter from load and AE cumulative event count in the early stage of the sloped finger-jointed specimens bonded with polyvinyl acetate, oilic urethane and resorcinol-phenol resin adhesives was much greater than that between the MOE and the MOR. Therefore, the AE signals obtained during bending test are useful for estimating the strength of sloped finger-jointed specimens.

• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.721-725
• /
• 2004

Multiple-count problem is occurred when rectangle objects span across several buckets. The Cumulative Density (CD) histogram is a technique which solves multiple-count problem by keeping four sub-histograms corresponding to the four points of rectangle. Although it provides exact results with constant response time, there is still a considerable issue. Since it is based on a query window which aligns with a given grid, a number of errors may be occurred when it is applied to real applications. In this paper, we proposed selectivity estimation techniques using the generalized cumulative density histogram based on two probabilistic models: (1) probabilistic model which considers the query window area ratio, (2) probabilistic model which considers intersection area between a given grid and objects. In order to evaluate the proposed methods, we experimented with real dataset and experimental results showed that the proposed technique was superior to the existing selectivity estimation techniques. The proposed techniques can be used to accurately quantify the selectivity of the spatial range query on rectangle objects.

• Communications for Statistical Applications and Methods
• /
• v.25 no.1
• /
• pp.29-42
• /
• 2018

We combine the integer-valued GARCH(1, 1) model with a generalized regime-switching model to propose a dynamic count time series model. Our model adopts Markov-chains with time-varying dependent transition probabilities to model dynamic count time series called the generalized regime-switching integer-valued GARCH(1, 1) (GRS-INGARCH(1, 1)) models. We derive a recursive formula of the conditional probability of the regime in the Markov-chain given the past information, in terms of transition probabilities of the Markov-chain and the Poisson parameters of the INGARCH(1, 1) process. In addition, we also study the forecasting of the Poisson parameter as well as the cumulative impulse response function of the model, which is a measure for the persistence of volatility. A Monte-Carlo simulation is conducted to see the performances of volatility forecasting and behaviors of cumulative impulse response coefficients as well as conditional maximum likelihood estimation; consequently, a real data application is given.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.9
• /
• pp.74-85
• /
• 1995

The purpose of this paper is to evaluate the grade of WA vitrified and resinoid bond grinding wheels by the sue of AE measuring system. When the manufactured 48 kinds of specimens were scratched by the method of OKOSHI'S grade test, the relationship between the amount of bit scratch depth of grinding wheel specimens and the character- istics of AE signals, and the relationship of AE counts and grade were considered as fololws; (1) The higher the grades are AE cumlulative event counts N and AE event count rate n, the smaller the values tend to be. But A $E_{rms}$is in reverse. (2) In the case of same grade, the smaller the grain size is, the higher the value of AE cumulative event counts N and A $E_{rms}$is results of comparison and observation. The grinding wheel with lower elasticity and with higher percentage of pore detected higher value of AE cumula- tive event counts N than with higher elasticity and lower percentage of pore. But A $E_{rms}$ is in reverse. (3) AE cumulative event counts N and bit scratch depth h have normally one to one correspondence. (4) It can be expected that quantitative evaluations of grade by using AE have been carried out by the wave observation of AE signal in line with the relationship between load speed of bit and AE cumulative event counts N & AE event count rate n.' AE event count rate n.ate n.

• Industrial Engineering and Management Systems
• /
• v.4 no.1
• /
• pp.75-81
• /
• 2005

Borror et al. discussed the EWMA(Exponentially Weighted Moving Average) chart to monitor the count of defects which follows the Poisson distribution, referred to the $EWMA_c$ chart, as an alternative Shewhart c chart. In the $EWMA_c$ chart, the Markov chain approach is used to calculate the ARL (Average Run Length). On the other hand, in order to monitor the process fraction defectives P in high-yield processes, Xie et al. presented the CCC(Cumulative Count of Conforming)-r chart of which quality characteristic is the cumulative count of conforming item inspected until observing $r({\geq}2)$ nonconforming items. Furthermore, Ohta and Kusukawa presented the $CS(Confirmation Sample)_{CCC-r}$ chart as an alternative of the CCC-r chart. As a more superior chart in high-yield processes, in this paper we present an $EWMA_{CCC-r}$ chart to detect more sensitively small or moderate shifts in P than the $CS_{CCC-r}$ chart. The proposed $EWMA_{CCC-r}$ chart can be constructed by applying the designing method of the $EWMA_C$ chart to the CCC-r chart. ANOS(Average Number of Observations to Signal) of the proposed chart is compared with that of the $CS_{CCC-r}$ chart through computer simulation. It is demonstrated from numerical examples that the performance of proposed chart is more superior to the $CS_{CCC-r}$ chart.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.2
• /
• pp.84-91
• /
• 2003

In this study, the three species (Populus euramericana, Pinus densiflora and Quercus variabilis) were cut to difference (0, 0.15, 0.3, 0.45 mm) between the size of tip and that of root of the finger (DSTR) and jointed with poly vinyl acetate (PVA) and resorcinol-phenol resin (RPR). We described the relationship between the bending strength properties of finger DSTR and the acoustic emission (AE) generated during the bending test. The results were as follows: The AE generation time of finger-jointed specimens with RPR adhesive was earlier than that with PVA adhesive. The AE cumulative event count of finger-jointed specimens with RPR adhesive continuously increased with increasing load and the event count was much more than that with PVA adhesive. Also, the AE cumulative event count for resorcinol-phenol resin adhesive obtained from low load level was abundant. The AE wave in finger-jointed specimens with RPR adhesive could be detected in the below proportional limit load. Therefore, AE signals from bending test are useful for the estimation of strength in finger DSTR specimens.

• Journal of Applied Reliability
• /
• v.13 no.2
• /
• pp.129-140
• /
• 2013

As a fundamental experimental study for reliability improvement of lithium ion secondary battery, degradation mechanism was investigated by microscopic observation and acoustic emission monitoring. Microstructural observation of the decomposed battery after cycle test revealed mechanical and chemical damages such as interface delamination, microcrack of the electrodes, and solid electrolyte interphase (SEI). Acoustic emission (AE) signal was detected during charge and discharge of lithium ion battery to investigate relationships among cumulative count, discharge capacity, and microdamages. With increasing number of cycle, discharge capacity was decreased and AE cumulative count was observed to increase. Observed damages were attributed to sources of the detected AE signals.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.2
• /
• pp.198-204
• /
• 2013

Acoustic emission(AE) signal was detected during charge and discharge of lithium ion battery to investigate relationships among cumulative count, discharge capacity, and microdamages. AE signal was received during accelerated charge/discharge cycle test of a coin-type commercial battery. A number of AE signals were successfully detected during charge and discharge, respectively. With increasing number of cycle, discharge capacity was decreased and AE cumulative count was observed to increase. Microstructural observation of the decomposed battery after cycle test revealed mechanical damages such as interface delamination and microcracking of the electrodes. These damages were attributed to sources of the detected AE signals. Based on a linear correlation between discharge capacity and cumulative count, feasibility of AE technique for evaluation of battery degradation was suggested.

• Journal of Ocean Engineering and Technology
• /
• v.26 no.5
• /
• pp.5-10
• /
• 2012

In this study, carbon steel (A53) is used as the material for the pipes in a marine plant and ship industry. Welds are necessary to join the carbon steel, and the effect of this welding on the properties of the carbon steel has been studied by many researchers. In this study, the dynamic behavior of welded carbon steel was studied using an acoustic emission (AE) technique, which is a nondestructive test. There are numerous AE parameters that can be used to analyze the damage behavior of carbon steel by external loading. The AE parameters of energy, cumulative count, amplitude, and AE event were used, and each parameter was differentiated according to the degree of damage to the carbon steel. The energy showed a high level at the elastic range of the load curve, while the amplitude had the highest value at the hardening region. The cumulative count showed a growth tendency similar to the loading curve. In addition, an ultrasonic technique and hardness test were applied to evaluate the mechanical properties according to the base zone, HAZ region, and weld zone of the weld specimen. The velocity and attenuation ratio showed little change between zones, and an evaluation of the ultrasonic waves on each zone of the specimen was found to be a useful method to clarify the mechanical properties of the carbon steel.