• 한국주조공학회지
• /
• 제36권1호
• /
• pp.24-31
• /
• 2016

CD4MCU duplex stainless steel with gadolinium was fabricated as a neutron absorbing material by the air induction melting method. The gadolinium formed intermetallic compounds of Cu-Gd-Fe. There were no significant differences in hardness or ultimate tensile strength between experimental alloys. With the addition of gadolinium the yield strength of the cast alloy significantly increased, from $478.8{\pm}11.6$ to $514.2{\pm}29.9MPa$, whereas elongation of the cast alloy decreased with the addition of gadolinium, from $26.0{\pm}7.1$ to $7.0{\pm}2.5%$ due to the formation of gadolinium based intermetallic compounds.

• 한국분말재료학회지
• /
• 제14권4호
• /
• pp.261-264
• /
• 2007

The electromagnetic wave (EM) absorption properties of various particle size have been investigated in a sheet-type absorber using the $Fe_{73}Si_{16}B_{7}Nb_{3}Cu_{1}$ alloy powder. With decreasing the average particle size, the complex permeability (${\mu}_{r}$) and permittivity (${\varepsilon}_{r}$) increased and the matching frequency is shifted toward lower frequency. The fabricated EM wave absorbers showed permeability $2{\sim}6$, permittivity $17{\sim}23$ for a $-325{\sim}+400$ mesh sample, and the calculated power absorption was as high as 80% in the frequency range over 2 GHz.

• 대한금속재료학회지
• /
• 제50권7호
• /
• pp.531-538
• /
• 2012

In this study, we evaluated the fluidity of the Al-Zn based alloys which exhibit excellent mechanical properties. We conducted computer simulations of fluid flow using the results of DSC, DTA analysis and Java-based Materials Properties software (J. Mat. Pro). Such computer simulations were then compared with the results obtained from experimental observations. The computer simulation results and the experimental results were very similar in fluidity length. It was found that the fluidity length of Al-Zn alloys is improved by increasing the Zn content while decreasing the solidus temperature of an alloy. In addition, we elucidate the effect of Zn addition on variations in different mechanical properties and the microstructure characteristics of (Al-xZn3Cu0.4Si0.3Fe) x=20, 30, 40, and 45 wt% alloys fabricated by gravity casting.

• 한국분말재료학회지
• /
• 제15권1호
• /
• pp.53-57
• /
• 2008

The amorphous $Fe_{73}Si_{16}B_7Nb_3Cu_1$(at%) alloy strip was pulverized using a jet mill and an attrition mill to get flake-shaped powder. The flake powder was mixed with dielectric $BaTiO_3$ powder and its dispersant to increase the permittivity. The powders covered with dielectric powders and its dispersant were mixed with a binder and a solvent and then tape-cast to form sheets. The absorbing properties of the sheets were measured to investigate the roles of the dielectric powder and its dispersant. The results showed that the addition of $BaTiO_3$ powders and its dispersant improved the absorbing properties of the sheets noticeably. The powder sheet mixed with 5 wt% of $BaTiO_3$ powder and 1 wt% of dispersant showed the best electromagnetic wave absorption rate because of the increase of the permittivity and the electrical resistance.

• 한국분말재료학회지
• /
• 제14권5호
• /
• pp.303-308
• /
• 2007

The oxidation of $Fe_{73}Si_{16}B_7Nb_3Cu_1$ nanocrystalline powder has been conducted to investigate its influence on the electromagnetic wave absorption characteristics of the soft magnetic material. Oxidation occurred primarily on the surface of nanocrystals. Oxidation reduced the real part of complex permeability due to the reduction of the relative volume of the powder, which otherwise contributes to the permeability. Oxidation reduced the absorption efficiency of the sheet at frequencies over 1GHz, indicating that the relative contribution of skin depth increments to the absorption was not significant. The pulverization and milling process lowered the optimum crystallization temperature of the material by $40{\sim}50^{\circ}C$ because of the internal energy accumulated during the fragmentation and powder thinning processes.

• Journal of Magnetics
• /
• 제9권2호
• /
• pp.65-68
• /
• 2004

Magnetically soft nanomaterials obtained by controlled crystallisation of metallic glasses are the newest group of materials for inductive components. In particular, research is carried out in the field of alloys for high temperature applications. This kind of materials must meet two basic requirements: good magnetic properties and stability of properties and structure. In the present work the magnetic properties and structure of Fe-Co-Hf-Zr-Cu-B (HIDTPERM-type) alloys were investigated, as well as their stability. Differential thermal analysis, (DTA), X-ray diffractometry (XRD), transmission electron microscopy (TEM), magnetometry (VSM) and quasistatic hysteresis loop recording were used to characterise structure and properties of the alloys investigated. Optimisation against properties and their stability was performed, resulting in formulation of chemical composition of the optimum alloy, as well as its heat treatment.

• 한국분말재료학회지
• /
• 제15권2호
• /
• pp.142-147
• /
• 2008

The hypereutectic Al-20 wt%Si powders including some amount of Cu, Fe, Mg, Mn were prepared by a gas atomization process. In order to get highly densified Al-Si bulk specimens, the as-atomized and sieved powders were extruded at $500^{\circ}C$, Microstructure and tensile properties of the extruded Al-Si alloys were investigated in this study. Relative density of the extruded samples was over 98%. Ultimate tensile strength (UTS) in stress-strain curves of the extruded powders increased after T6 heat treatments. Elongation of the samples was also increased from 1.4% to 3.2%. The fracture surfaces of the tested pieces showed a fine microstructure and the average grain size was about $1{\mu}m$.

• 보존과학회지
• /
• 제29권4호
• /
• pp.355-366
• /
• 2013

전세품인 청동기를 대상으로 ICP-AES, SEM-EDS와 두 종류의 P-XRF (Bench top type, Gun type)를 이용하여 성분분석과 미세조직 관찰을 실시하였다. 또한 전세품 청동기의 성분 함유량을 분석하는 과학적 분석을 이용하여 특이원소의 검출에 따른 청동기의 진위 판별에 대한 적용성 연구를 실시하였다. ICP-AES의 분석 결과 청동기는 3원 합금(Cu-Sn-Pb계)의 청동으로 Ag, As, Co, Fe 등의 미량 성분이 검출되었으며 특이 원소(Zn 등)는 검출되지 않았다. P-XRF 분석결과 ICP-AES 분석결과와 비교하였을 때 Cu의 함유량은 10~25% 낮고, Sn 함유량은 10~20% 높게 검출되었다. 이는 탈주석 현상으로 Sn의 함유량이 높은 산화주석($SnO_2$) 화합물이 청동기 표면에 존재하여 영향을 주는 것으로 판단되었다. 그리고 SEM-EDS 분석결과 Pb의 편석 현상을 확인할 수 있었다. 이러한 과학적 분석 방법을 이용하여 청동 소지층과 부식층(표면)의 성분 조성 관계가 서로 다르게 나타나는 것을 확인하였다. 청동유물은 미세조직 및 성분분석 결과만으로 진위판별에 대한 결과를 적용하기가 어려웠다. 따라서 매장 환경 및 유물의 보존 상태 등에 따라 부식생성물질이 서로 다른 양상을 보이는 것에 착안하여 부식생성물질에 대한 추가적인 연구와 고고미술사적인 비교연구를 통하여 진위여부를 확인할 수 있을 것으로 사료된다.

• 한국분말재료학회지
• /
• 제11권5호
• /
• pp.412-420
• /
• 2004

The purpose of the present study is to determine an optimum composition using cheaper powders keeping with high performance of hard rock cutting diamond saw blade. With 50Fe-20(Cu . Sn)-30Co specimen, a part of Co was replaced by Ni(5%, 10%, and 15%, respectively). These specimens were hot pressed and sintered for predetermined time at various temperature. Sintering is performed by two different methods of temperature controlled method and specimen dimension controlled method. In order to determine the property of the sintered diamond saw blade, 3 point bending tester, X-ray diffractometer, and SEM were used. As the Co in the bond alloy was replaced by Ni, the hardness of the specimen increased. Thus the 50Fe-20(CuㆍSn)-15Co-15Ni specimen showed the maximum hardness of 104(HRB). The results of 3 point bending test showed that flexure strength decreased along with increase in Ni content. This is attributed to the formation of intermetallic compound(Ni$_{x}$Sn) determined by X-ray diffraction. The fracture surface after 3 point bending test showed that diamond was fractured in the specimen containing 0%, 5%, and 10%Ni, and the fracture occurred at the interface between diamond and matrix in the specimen containing 15%Ni. The cutting ability test showed that the abrasive property was not changed in the specimen containing 0%, 5%, and 10%Ni. The optimum composition determined in this study is 50Fe-20(CuㆍSn)-20Co-10Ni.

• 대한금속재료학회지
• /
• 제48권6호
• /
• pp.523-532
• /
• 2010

Co-application of organic coating and cathodic protection has not provided enough durability to low-alloyed steels inseawater ballast tank (SBT) environments. An attempt has made to study the effect of alloy elements (Al, Cr, Cu, Mo, Ni, Si, W) on general and localized corrosion resistance of steels as basic research to develop new low-allowed steels resistive to corrosion in SBT environments. For this study, we measured the corrosion rate by the weigh loss method after periodic immersion in synthetic seawater at $60^{\circ}C$, evaluated the localized corrosion resistance by an immersion test in concentrated chloride solution with the critical pH depending on the alloy element (Fe, Cr, Al, Ni), determined the permeability of chloride ion across the rust layer by measuring the membrane potential, and finally, we analyzed the rust layer by EPMA mapping and compared the result with the E-pH diagram calculated in the study. The immersion test of up to 55 days in the synthetic seawater showed that chromium, aluminium, and nickel are beneficial but the other elements are detrimental to corrosion resistance. Among the beneficial elements, chromium and aluminium effectively decreased the corrosion rate of the steels during the initial immersion, while nickel effectively decreased the corrosion rate in a longer than 30-day immersion. The low corrosion rate of Cr- or Al-alloyed steel in the initial period was due to the formation of $Cr_2FeO_4$ or $Al_2FeO_4$, respectively -the predicted oxide in the E-pH diagram- which is known as a more protective oxide than $Fe_3O_4$. The increased corrosion rate of Cr-alloyed steels with alonger than 30-day exposure was due to low localized corrosion resistance, which is explained bythe effect of the alloying element on a critical pH. In the meantime, the low corrosion rate of Ni-alloyed steel with a longer than 30-day exposure wasdue to an Ni enriched layer containing $Fe_2NiO_4$, the predicted oxide in the E-pH diagram. Finally, the measurement of the membrane potential depending on the alloying element showed that a lower permeability of chloride ion does not always result in higher corrosion resistance in seawater.