• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.2
• /
• pp.129-136
• /
• 2017

Characteristics of $ZrO_2$ felt supported Cu/Zn catalysts have been investigated for the production of hydrogen via methanol steam reforming. Cu and Zn in different weight percent were loaded using wet impregnation over $ZrO_2$ felt support. The catalysts were characterized with BET and FE-SEM. The performance of these synthesized catalysts were investigated at SCR=1.5, $GHSV=2000h^{-1}$, temperature=$300{\sim}400^{\circ}C$, and pressure=2.5~19.5 barA. The results showed that the $Cu^{32.5}Zn^{7.5}ZrO_2$ catalyst was most active in terms of methanol conversion and hydrogen production. The methanol conversion in steam reforming of methanol was 84.6% at 19.5 barA and furnace $400^{\circ}C$ over $Cu^{32.5}Zn^{7.5}ZrO_2$ catalyst. The catalysts prepared using $ZrO_2$ felt show higher reactor temperature than the pellet type catalyst at same furnace temperature.

• Applied Chemistry for Engineering
• /
• v.4 no.4
• /
• pp.672-682
• /
• 1993

2, 4-Heptadione(abbreviated to 24HTD) was synthesized from methylpropyl ketone and ethyl acetate with sodium amide, and the equilibrium and the kinetic characteristics of copper extraction by 24HTD-chloroform were investigated. Equilibrium constants such as the dissociation constant and the distribution coefficient of 24HTD and the stability constant of the 24HTD-Cu chelate were evaluated from the spectrophotometry, and the overall equilibrium constant of the extraction was also determined. The extracted species of the 24HTD-Cu chelate was found to be $CuR_2$ and the initial rate of the extraction of coupper by 24HTD in chloroform was expressed by $R_0=k[\bar{HR}]([Cu^{2+}]/[H^+])^{0.5}$.

• Economic and Environmental Geology
• /
• v.35 no.1
• /
• pp.1-12
• /
• 2002

Manus Basin, located in the equatorial western Pacific, is a back arc basin formed by collision between the IndoAustralian and the Pacific Plates. The basin is host to numerous hydrothermal vent fields and ore deposits. The basement rocks of the Manus Basin consist primarily of dacite and basaltic andesite. Some of the minerals that form the hydrothermal chimneys that were dredged on the Manus basin include pyrite, chalcopyrite, marcasite, sphalerite and galena. The chimneys can be classified into chalcopyrite dominant Cu-rich type and sphalerite dominant Zn-rich type. The concentration of Zn shows good positive correlation with that of Sb, Cd and Ag. The content of Cu, on the other hand, positively correlates with that of Mo, Mn and Co. For samples that were taken from Zn-rich chimney, a strong positive correlation is found between Au and Zn contents. The chimney also shows enrichments of Cd, Mn and Sb. On the other hand, the samples from Cu-rich chimney exhibit strong correlation among Au, Zn and Pb, and are enriched in Mo and Co concentration. Average contents of Au in Cu-rich and Znrich chimneys were 15.9 ppm and 29.0 ppm, respectively. Because of high concentration of Au with Ag and Cu, the ore deposit have high economic potential. Homogenization temperatures and salinities of fluid inclusions in anhydrite and amorphous silica from Zn-rich chimney are estimated to be l74-220$^{\circ}$C and 2.7-3.6 equiv. wt. % NaCI, respectively. These value suggest that ore forming processes were occurred at around 200$^{\circ}$C and that the oxygen fugacity changed from 2: 10$^{-39.5}$bar to -s: 10$^{-40.8}$bar and the sulfur fugacity from -s: 10$^{-14.7}$bar to 10$^{-13.4}$bar during the process. It appears that the temperature at which the ores formed on Cu-rich chimney was higher than that on Zn-rich chimney.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.2
• /
• pp.5-17
• /
• 2018

In this study, the in-situ stress, strength and stress-strain characteristics with shear parameters (UU, CU, ${\bar{CU}}$) are analytically evaluated and the stability analyses are carried out under loading/unloading conditions. The in-situ stress and the stress-strain behaviour may become different according to input shear parameters in finite element analyses with construction step, Especially, if the internal friction angle in Mohr-Coulomb model is set to zero, the in-situ stress and the stress-strain behaviour might not be properly predicted. The results from CU parameter of total stress analysis have no significant difference with the results from CU of effective stress analysis. Therefore, in the numerical analysis for soft ground, CU parameters can be applied to predict in-situ stress and stress-strain behaviors. In addition, the calculation method was proposed to determine the shear parameter of Mohr-Coulomb model, which is corresponding to the shear strength equivalent to that of in-situ soil.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.191.2-191.2
• /
• 2014

Cu/ZnO/$Al_2O_3$ is widely used methanol synthesis catalyst at elevated pressures P (50 to 100 bar) and temperatures T (473 to 573 K) using $CO_2$, CO, $H_2$ syngas mixture. Although Cu step and planar defects have been regarded as active sites in this catalyst, detailed $CO_2$ hydrogenation procedure has been still unknown and debated as well as initial intermediate. In this study, we investigated the mechanism of $CO_2$ hydrogenation on Cu(111) model surface at P (1 bar) and T (298 to 450 K) using reflection absorption infrared spectroscopy (RAIRS). Two distinct formates by hydrogenation of $CO_2$, on step and on terrace, show different behavior with elevating temperature. The peak intensity of on step formate was continuously decreased above 360 K up to 450K in contrast to the increase of on terrace formate. These phenomena are strong possibilities that the formate is initial intermediate and is desorbed by hydrogenation reaction because thermal desorption temperature of formate (~470 K) is much higher than desorption of on step formate. And the formate production peak of on step site was weakly correlated with CO formation.

• Membrane Journal
• /
• v.34 no.2
• /
• pp.146-153
• /
• 2024

In this experiment, a Ti-based flat hydrogen separation membrane was designed and manufactured. In order to find a Ti-based hydrogen separation membrane of a new composition, the correlation between the physical-chemical properties and hydrogen permeability of various alloys was investigated. Based on this, two types of new alloy films (Ti_14.2Zr_66.4Ni_12.6Cu_6.8 (70 ㎛), Ti_17.3Zr_62.7Ni₂₀ (80 ㎛)) was designed and manufactured. The manufactured flat hydrogen separation membrane was tested for hydrogen permeation using mixed gas (H₂, N₂) and sweep gas (Ar) at 300~500℃ and 1~4 bar. The Ti_14.2Zr_66.4Ni_12.6Cu_6.8 alloy film has a maximum flux of 16.35 mL/cm² min at 500℃ and 4 bar, and the Ti_17.3Zr_62.7Ni₂₀ alloy film has a maximum flux of 10.28 mL/cm² min at 450℃ and 4 bar.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.447-452
• /
• 2004

Vacuum interrupters in order to be used in various switch-gear components such as circuit breakers, distribution switches, contactors, etc. spread the arc uniformly over the surface of the contacts. The electrodes of vacuum interrupters are made of sinter-forged Cu-Cr materials for good electrical and mechanical characteristics. Since the closing velocity is 1-2m/s and impact deformation of the electrode depends on the strain rate at that velocity, the dynamic behavior of the sinter-forged Cu-Cr is a key to investigate the impact characteristics of the electrodes. The dynamic response of the material at intermediate strain rate is obtained from the high speed tensile test machine test and at the high strain rate is obtained from the split Hopkinson pressure bar test. Experimental results from both quasi-static and dynamic compressive tests are interpolated to construct the Johnson-Cook model as the constitutive relation that should be applied to simulation of the dynamic behavior of the electrodes. The impact characteristics of a vacuum interrupter are investigated with computer simulations by changing the amount of chromium content.

• Korean Journal of Food Science and Technology
• /
• v.33 no.3
• /
• pp.378-383
• /
• 2001

Formation of superoxide anion $O_2\bar{{\bullet}}$ in the autoxidation of L-ascorbic acid (AsA) in the presence of heavy metal ions were determined. The generation of $O_2\bar{{\bullet}}$ was studied by using superoxide dismutase (SOD) in aqueous and buffer solution, and using nitro bule tetrazolium (NBT) in methanol solution. The remaining amount of AsA was significantly higher in the presence of SOD than in its absence. It suggested that SOD stabilizes AsA in aqueous and buffer solution because of scavenging $O_2\bar{{\bullet}}$ formed during the autoxidation reaction of AsA in the presence of heavy metal ions. NBT has an absorption maximum at about 560 nm in methanol solution. The absorbance at 560 nm increased during the oxidation of AsA, suggested the formation of $O_2\bar{{\bullet}}$in methanol solution. Thus, the formation of $O_2\bar{{\bullet}}$ was confirmed during the autoxidation of AsA not only in aqueous solution but also in methanol solution in the presence heavy metal ions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.6 s.249
• /
• pp.670-677
• /
• 2006

Vacuum interrupters are used in various switch-gear components such as circuit breakers, distribution switches, contactors. The electrodes of a vacuum interrupter are manufactured of sinter-forged Cu-Cr material for good electrical and mechanical characteristics. Since the closing velocity is 1-2m/s and impact deformation of the electrode depends on the strain-rate at the given velocity, the dynamic material property of the sinter-forged Cu-Cr alloy is important to design the vacuum interrupter reliably and to identify the impact characteristics of a vacuum interrupter accurately. This paper is concerned with the dynamic material properties of sinter-forged Cu-Cr alloy for various strain rates. The amount of chrome is varied from 10 wt% to 30 wt% in order to investigate the influence of the chrome content on the dynamic material property. The high speed tensile test machine is utilized in order to identify the dynamic property of the Cu-Cr alloy at the intermediate strain-rate and the split Hopkinson pressure bar is used at the high strain-rate. Experimental results from both the quasi-static and the high strain-rate up to the 5000/sec are interpolated with respect to the amount of chrome in order to construct the Johnson-Cook and the modified Johnson-Cook model as the constitutive relation that should be applied to numerical simulation of the impact behavior of electrodes.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.1
• /
• pp.89-94
• /
• 2007

High duality BiSrCaCuO thin films fabricated by using the i-beam sputtering method at various substrate temperatures, $T_{sub}$ and oxidation gas pressures, $pO_3$. The correlation diagrams of the BiSrCaCuO phases with Tsub and $pO_3$ are established in the 2212 and 2223 compositional films. In spite of 2212 compositional sputtering, Bi2201 and Bi2223 as well as Bi2212 phases come out as stable phases depending on $T_{sub}$ and $pO_3$. From these results, the thermodynamic evaluation of ${\Delta}H$ and${\Delta}S$, which are related with Gibbs' free energy change for single Bi2212 or Bi2223 phase, was performed.