• Computers and Concrete
• /
• v.19 no.5
• /
• pp.451-455
• /
• 2017

Technological advancements in the field of building materials are achieved day by day. In this study, a new lightweight concrete aggregate is produced by mixing certain rates of colemanite (0%, 7.5%, 12.5%, 17.5%), cement and coating the surface of pumice aggregate with this mixture. Thin aggregate sections are analyzed with specific gravity, unit weight, water absorption, impact, and crushing experiments. In this way, the production of cement and cement+colemanite coated lightweight concrete aggregates is investigated and an opinion on the likely behavior of these concrete types is provided.

• Journal of Industrial Technology
• /
• v.16
• /
• pp.105-112
• /
• 1996

This paper presents coal mine waste (CMW) for use in concrete manufacture as a replacement of normal aggregates. The CMW in this study was collected from Sabook, Jungson-kun, Kangwon-do. Fine and coarse asggregates from CMW were prepared by crushing it in a jaw crusher and separating debris with #4 sieve. CMW aggregates showed good physical and mechanical properties with having specific gravity over 2.65, absorption less than 1%, and abration ratio below 20%, but particle shape of CMW was long or flat, which caused a poor workability in mixing. Therefore, to make workability better, a 1/4 of CMW coarse aggregate was replaced with normal aggregate which had a good particle shape, and a superplasticizer was added to the mix. Compressive strength and other mechanical properties of CMW concrete was very good. In conclusion, characteristics of CMW concrete was acceptable for use as a concrete structural material.

• Journal of the Korean Ceramic Society
• /
• v.28 no.11
• /
• pp.926-934
• /
• 1991

The effect of aggregates on the forming and sintering behaviors of BaTiO3 was studied. Aggregates and deaggregates of fine crystallite were obtained by thermal decomposition of oxalate coprecipitates and subsequently crushing them with a press, respectively. Large voids formed by packing of aggregates were not easily eliminated despite the successive destruction of aggregates with increasing forming pressure. As a result, compacts of aggregates showed inhomogeneity with larger mid-pore size and broader pore size distribution with respect to those of deaggregates. This inhomogeneity caused differential shrinkage and consequental internal stress, which retarded densification. The differential sintering increased the size of mid-pores in the initial stage, and formed duplex structure composed of dense region with abnormally grown grains and porous region with fine grains. The driving force of this abnormal grain growth shown in the specimens of aggregates was attributed to the minimization of the elastic strain energy due to internal stress.

• International Journal of Automotive Technology
• /
• v.5 no.1
• /
• pp.47-53
• /
• 2004

In this paper, a modified and representative unit cell model was employed to study the crush behaviour of a closed cell metallic foam. The unit cell which captures the main geometrical features of the metallic foam considered was used to simulate crush behaviour in metallic foams. Both analytical using limit analysis and numerical using the finite element method were used to study the collapse behaviour of the cell. The analytical crushing stress of the foam was compared with FE results and was found to be in good agreement.

• Transactions of Materials Processing
• /
• v.5 no.1
• /
• pp.18-26
• /
• 1996

In order to investigate the effect of pre-cooling of ingot on void closure in hot plate forging the internal strain and stress distributions are examined quantitatively by using ABAQUS. Simula-tions are carried out on a large slab ingot having the same temperature and the temperature gradient induced by air-cooling. It is shown that pre-cooling produces little effect on the strain behavior but remarkable effect on the hydrostatic stress at the central zone of ingot. The main factors for crushing micro-voids are the effective strain and the time integral of hydrostatic stress in the region surrounding the voids. Based on regression analysis it was found that the distortion of void can be expressed as a polynomial function of the two factors.

• Journal of the Korean Ceramic Society
• /
• v.29 no.10
• /
• pp.797-805
• /
• 1992

Al2O3-20 wt% ZrO2 composite powders to be used as the starting materials of the Al2O3/ZrO2-Spinel composite system were prepared by the use of the emulsion-hot kerosene drying method. The crystalline phase of ZrO2 in the synthesized Al2O3-ZrO2 composite powders was 100% tetragonal but the small amount of t-ZrO2 was transformed into m-ZrO2 after crushing. The hardness, fracture toughness, and flexural strength of the composite, which was sintered at 1650$^{\circ}C$ for 4 hrs after calcining at 1100$^{\circ}C$ for 2 hrs and had the relative density of 99%, were 15.7 GPa, 4.97 MN/m3/2, and 390 MPa, respectively. The fracture form in the sintered composites was found to be the intergranular fracture.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.373-376
• /
• 2004

The designer has difficulty due to inadequacy of provisions in the domestic design code and lack of understanding for behavior of D-region. The rectangular shaped corbel consist of various failure mechanisms as the crushing or splitting from compression concrete, and shearing failure under the loading plate. However, predicting those failure mechanisms is very difficult. In this study, rectangular shaped corbel is analyzed and designed by using strut-tie model. Adequacy for the application of strut-tie model is verified by comparison with the way used in current design practice. The results show that strut-tie model can be a rational and an economical design than current conventional design methods.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.213-216
• /
• 2006

The designer has difficulty due to inadequacy of provisions in the domestic design code and lack of understanding for behavior of D-region. The reinforced concrete pi(${\pi}$)-shaped RC rahmen bridge consists of various failure mechanisms as the crushing or splitting from compression concrete, and shearing failure under the loading plate. However, predicting those failure mechanisms is very difficult. In this study, the pi(${\pi}$)-shaped RC rahmen bridge is analyzed and designed by using strut-tie model. Adequacy for the application of strut-tie model is verified by comparison with the way used in current design practice. As a result that designing the structures should be maked a comparison between strut-tie model and current conventional design method.

• Steel and Composite Structures
• /
• v.36 no.2
• /
• pp.187-196
• /
• 2020

Double skin composite wall system owns several structural merits in terms of high load-carrying capacity, large axial stiffness, and favorable ductility. A recently proposed form of truss connector was used to bond the steel plates to the concrete core to achieve good composite action. The structural behavior of rectangular high walls under compression and T-shaped high walls under eccentric compression has been investigated by the authors. Furthermore, the influences of the truss spacings, the wall width, and the faceplate thickness have been previously studied by the authors on short walls under uniform compression. This paper experimentally investigated the effect of width-to-thickness ratio on the compressive behavior of short walls. Compressive tests were conducted on three short specimens with different width-to-thickness ratios. Based on the test results, it is found that the composite wall shows high compressive resistance and good ductility. The walls fail by local buckling of steel plates and crushing of concrete core. It is also observed that width-to-thickness ratio has great influence on the compressive resistance, initial stiffness, and strain distribution across the section. Finally, the test results are compared with the predictions by modern codes.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.5
• /
• pp.199-210
• /
• 2003

The development of strain localization within shear zones is frequently observed during soil deformation. In fact, the phenomenon appears to be more often the norm rather than the exception. Conceptually, any soil condition that renders negative work increment is prone to localization. In this study, a broad range of soil and loading conditions are investigated to test this criterion, including: dilative soil subjected to drained shear (standard case), contractive soil sheared under undrained conditions, cavitation in dilative soil in undrained shear, inhomogeneous soils, particle alignment in contractive soils made of platy particles, soils that experience particle crushing, and the shear of low-moisture and/or lightly cemented loose soils. Unique specimens and test procedures are designed to separately test each of these soil conditions in the laboratory According to experimental test results, soil specimens with post-peak strain softening behavior are prone to progressive failure, localization of deformations, and shear banding. The state of stress, the soil density, inherent mechanical and geometrical properties of soil particles, low water content, and heterogeneity can contribute to triggering strain localization. Considering all possible cases of localization, the best method to obtain the critical state line in the laboratory is to use contractive homogeneous specimens subjected to drained shear.