• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 춘계학술대회 논문집
• /
• pp.79-83
• /
• 1992

According to the variation of hydrostatic pressure on the central axis of deformable material, the V-shaped central bursting defect may be created on extrusion or drawing processes. The process factors whichaffect the generation of defects are die semi-angle, reduction ratio of cross-sectional area, friction factor, material properties and so on. The combination of these factors can determine the prossibility of defect creation and the shape of various round holes which have been created inside already. By the rigid plastic finite element method, this paper describes the observations of change in shape of a round hole with process conditions suchas die semi-angle, reduction ratio of cross-sectional area and friction factorat the unsteady state of axi-symmetrical extrusion process when the round hole is alreadyexisted inside the original billet, and also, the effects of process factors are investigated to prevent the possible defects.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2007년도 공동학술대회 논문집
• /
• pp.87-92
• /
• 2007

This work describes the installation and preliminary measurements of an electrical resistivity tomography (ERT) system to monitor the injection of recycled water into a confined aquifer in the area of Sindos (Thessaloniki N. Greece). The aim is to provide, through time-lapse ERT measurements and processing, geoelectrical images of rather increased volumetric sampling around and between the holes and to obtain improved understanding of the flow and transport of the injected water. The details about the general setting, the construction and installation of the ERT cables into the boreholes are explained in full. Preliminary measurements involving single and cross-hole ERT measurements were obtained and processed with a 2D inversion algorithm to produce images of the subsurface. Results depict a very good correlation between ERT images and the lithology and resistivity logs; an indication of the reliability of the approach.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 춘계 학술논문 발표대회
• /
• pp.98-99
• /
• 2015

In the study, based on analysing bond strength of MPC and existing rapid harding grout according to shape of cross section, early ages shape of cross section is investigated about effect on bond strength to use MPC as an emergency repair material for road defects such as the form of a pot-hole. The result, MPC is about 10% higher than the shear bond strength rapid harding grout, about 20% higher bending bond strength.

• 한국지반공학회논문집
• /
• 제25권11호
• /
• pp.53-60
• /
• 2009

터널의 시공은 항상 주변 암반의 손상을 초래한다. 발생하는 손상의 정도는 주변암반의 역학적 및 수리학적 거동에 영향을 미친다. 본 논문에서는 크로스홀 시험을 통하여 P 파 속도를 측정하여 터널주변 암반의 손상을 계측하였다. 발진공에서의 탄성파 신호발생을 위하여 기계적인 충격을 가하였으며 그 결과로 발생된 P파 신호는 잡음이 적으며 파의 초동 도달시간 판별이 용이하였다. 실험결과 암반의 손상이 예상되는 구간에서 P 파의 속도가 낮게 검측 되었다. 크로스홀 공 내 다중의 지점에서 P 파 계측을 수행하여 이차원 P 파 토모그래피를 생성하였는데, 생성된 토모그래피는 터널 배면의 암반 손상이 발생한 구간에 대한 가시적인 결과를 나타내었다. 측정된 P파의 속도로부터 간극율 또는 Q 값과의 상관관계를 통해 암반 특성의 정량적인 손상 평가가 가능하였다.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권3호
• /
• pp.296-314
• /
• 2016

This paper presents experimental and computational investigations of synthetic jets with a circular exit for improving flow control performance. First, the flow feature and vortex structure of a multiple serial circular exit were numerically analyzed from the view point of flow control effect under a cross flow condition. In order to improve separation control performance, experimental and numerical studies were conducted according to several key parameters, such as hole diameter, hole gap, the number of hole, jet array, and phase difference. Experiments were carried out in a quiescent condition and a forced separated flow condition using piezoelectrically driven synthetic jets. Jet characteristics were compared by measuring velocity profiles and pressure distributions. The interaction of synthetic jets with a freestream was examined by analyzing vortical structure characteristics. For separation control performance, separated flow over an airfoil at high angles of attack was employed and the flow control performance of the proposed synthetic jet was verified by measuring aerodynamic coefficient. The circular exit with a suitable hole parameter provides stable and persistent jet vortices that do beneficially affect separation control. This demonstrates the flow control performance of circular exit array could be remarkably improved by applying a set of suitable hole parameters.

• 대한기계학회논문집B
• /
• 제28권3호
• /
• pp.304-314
• /
• 2004

An experimental study has been conducted to measure the temperature fields and the local film cooling effectiveness for two and three staggered rows of the rectangular shaped-holes with various blowing rates. The hydraulic diameter of rectangular-shaped hole is 10mm. To compare with the film cooling performance of rectangular-shaped hole, two kinds of circular holes are tested. One has the same hydraulic diameter as the rectangular hole and the other has the same cross sectional area. Also, rectangular holes with expanded exit with same inlet area as rectangular ones are tested. Temperature fields are measured using a thermocouple rake attached on three-axis traversing system. Adiabatic film cooling effectiveness on the surface are obtained based on experimental results of thermochromic liquid crystals. The film cooling effectiveness is measured for various blowing rates and compared with the results for the cylindrical holes. In case of 2 rows, the rectangular holes has better performance than circular holes due to its slot-like geometry. In case of 3 rows, the effecta of hole shape is not clear.

• 한국정밀공학회지
• /
• 제24권12호
• /
• pp.50-56
• /
• 2007

Femtosecond laser ablation of the Invar alloy and hole drilling for a shadow mask are studied. We used a regenerative amplified Ti-sapphire laser with a 1kHz repetition rate, 184fs pulse duration and 785nm wavelength. Femtosecond laser pulse was irradiated on the Invar alloy with air blowing at the condition of various laser peak power. An ablation characteristic of the Invar alloy was appeared non-linear at $125J/cm^2$ of energy fluence. For the application to a shadow mask, the hole drilling of the Invar alloy with the cross section of a trapezoidal shape was investigated. The ablated micro-holes were characterized using an atomic force microscopy(AFM). The optimal condition of hole pattern f3r a shadow mask was $4\;{\mu}m$ z-axis feed rate, 0.2mm/s circular velocity, $26.4{\mu}J$ laser peak power. With the optimal processing condition, the fine circular hole shape without burr and thermal damage was achieved. Using the femtoseocond laser system, it demonstrates excellent tool for the Invar alloy micro-hole drilling without heat effects and poor edge.

• 대한기계학회논문집B
• /
• 제21권7호
• /
• pp.849-861
• /
• 1997

In this study, the effect of hole geometry of the cooling system on the flow and temperature field was numerically calculated. The finite volume method was employed to discretize the governing equation based on the non-orthogonal coordinate with non-staggered variable arrangement. The standard k-.epsilon. turbulence model was used and also the predicted results were compared with the experimental data to validate numerical modeling. The predicted results showed good agreement in all cases. To analyze the effect of the discharge coefficient for slots of different length to width, the inlet chamfering and radiusing holes were considered. The discharge coefficient was increased with increment of the chamfering ratio, radiusing ratio and slot length to width and also the effect of radiusing showed better result than chamfering in all cases. In order to analyze the difference between the predicted results with plenum region and without plenum region, the velocity profiles of jet exit region for a various flow conditions were calculated. The normal velocity components of jet exit showed big difference for the low slot length to width and high blowing rate cases. To analyze the flow phenomena injected from a row of inclined holes in a real turbine blade, three dimensional flow and temperature distribution of the region including plenum, hole and cross stream with flow conditions were numerically calculated. The results have shown three-dimensional flow characteristics, such as the development of counter rotating vortices, jetting effect and low momentum region within the hole in addition to counter rotating vortex structure in the cross stream.

• 정보처리학회논문지B
• /
• 제17B권2호
• /
• pp.115-124
• /
• 2010

최근 스테레오 정합 기술은 정합하고자 하는 픽셀을 포함한 국부적인(local) 영상의 정합 비용과 시차의 변화 비용을 누적하는 전역적(global)인 방법을 많이 사용하고 있다. 특히 전역적 스테레오 정합에서도 비용누적 (cost accumulation)의 방향을 일반적인 수평방향이 아닌 다수의 방향을 사용하는 연구가 늘고 있다. 본 논문에서는 기존의 스테레오 정합 기술을 다중 방향성 정합 기술로 확장하는 방법을 제안한다. 픽셀의 국부적인 정합 비용은 단순한 NCC (Normalized Cross Correlation)를 사용하였고 전역적 정합 기술의 하나인 정합선 최적화(Scan-line Optimization) 방법을 다중 방향으로 확장하는 기술을 제안하였다. 우선 정합선 최적화를 다중 방향으로 실행한 후 이들 결과를 이용하여 신뢰도가 높은 시차영상 (disparity image)을 획득한다. 반복적인 다중 방향 정합선 최적화 시행 후, 시차영상에서 남은 공백은 홀 복원 방법으로 계산한다. 시차가 구해진 픽셀에 대해서는 신뢰도 점수를 매긴 다음 이 점수를 확산하여 신뢰도 점수 테이블에서 가장 높은 값을 가지는 시차값으로 홀을 복원하였다. 제안하는 기술을 미들버리(Middlebury)의 스테레오 영상을 사용하여 오차를 분석하였다. 기존의 전역적 방법과 제안 기술을 이용하여 시차영상을 계산하고 그 오차를 비교하였다.

• 한국지반공학회논문집
• /
• 제22권11호
• /
• pp.37-45
• /
• 2006

1970년대 중반부터 bender elements를 이용하여 흙 공시체의 전단파 속도를 측정하는 기술이 발전되어 왔다. 얇은 피에조 세라믹판과 탄성 매질을 겹쳐서 만든 bender elements는 삼축입축시험장치의 저판(base)와 top cap에 설치하여 액츄에이터와 트랜스듀스로 각각 사용하여 공시체의 전단파 속도를 측정하고 있다. bender elements를 현장에 적용하는 예비 단계로, 최적의 벤더 제작과 기하학적 배치에 대한 연구를 실내 카올리나이트 토조에서 수행하였다. 이 예비시험에서 개발된 bender element를 사용하여 갯벌에서 크로스홀 방식과 인홀 방식으로 탄성파 시험을 수행하였다. 일련의 bender elements를 깊이 2m까지 삽입하여 현장시험의 적용성을 확인하였다. 추후 깊은 심도까지 삽입할 수 있는 맨드렐(mandrel)과 관입장치를 개발하여 연약지반의 탄성파 속도 측정 장치 개발을 완성하고자 한다.