• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1981-1986
• /
• 2004

A cross-flow fan relatively makes high dynamic pressure at low speed because a working fluid passes through an impeller blade twice and blades have a forward curved shape. Therefore, the performance of a cross-flow fan is influenced 25% by the impeller, 60% by the rearguider and the stabilizer, 15% by the heat exchanger. At the low flow rate, there exists a rapid pressure head reduction, a noise increase and an unsteady flow against a stabilizer and a rearguider. Moreover, it is difficult to analyze the reciprocal relations of the cross-flow fan because each parameter is independent. Numerical analyses are conducted with different starting angles of the rearguider. Two-dimensional, unsteady governing equations are solved, using FVM, PISO algorithm, sliding grid system and ${\kappa}-{\varepsilon}$ standard turbulence model.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.61-64
• /
• 2008

The present study of these experiments are close examination of spray characteristics that are continuous liquid jet and modulated pressure pulse liquid jet. The experiments were conducted using water, over a range of cross-flow velocities from 42${\sim}$136 m/s, with injection frequencies of 35.7${\sim}$166.2 Hz. Between continuous cross-flow jet and pressure pulsed cross-flow jet for characteristics of penetration, breakup point, spray angle and macro spray shape are investigated experimentally. In cross-flow field, main parameter of liquid jet for breakup was cross-flow stream rather than pressure pulse frequency. As oscillation of the periodic pressure that could make liquid jet moved up and down, the mixing efficiency was increased. Also, a bulk of liquid jet puff was detected at upper field of liquid surface. So, this phenomenon has a good advantage of mixing spray from concentration of center area to outer area. Because of pressure pulsation frequency, an inclination of SMD for the structured layer was evanescent. Cross-sectional characteristics of SMD at downstream area were non-structured distributions. Then cross-sectional characteristics of SMD size were about same tendency over a range that is effect of spray mixing. The tendency of volume flux value for various frequency of pressure pulse was same distribution. And volume flux was decreased when the frequency of pressure pulse increase.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.10
• /
• pp.923-928
• /
• 2014

Elongation rolling process is an intermediate process to make the uniform thickness and uniform surface roughness during producing seamless pipes. The thickness and surface roughness of seamless pipes are generally affected by the distance of rolls and guide shoes, the roll shape, and its cross angle. In this study, finite element analysis for shape forming process is based on the analysis model of elongation rolling mill with guide shoes. This paper shows how the cross angle of the roll, the rolling rpm, and the distance of the guide shoe influence on the outer diameter and the thickness of seamless pipes. The rolling rpm did not give much influence on outer diameter.

• Structural Engineering and Mechanics
• /
• v.21 no.5
• /
• pp.591-620
• /
• 2005

A general analytical model for thin-walled composite beams with an arbitrary open/(or/and) closed cross section and arbitrary laminate stacking sequence i.e., symmetric, anti-symmetric as well as un-symmetric with respect to the mid plane of the laminate, is developed in the first paper. All the mechanical properties, mechanical centre of gravity and mechanical shear centre of the cross section are defined in the function of the geometry and the material properties of the section. A program "fungen" and "clprop" are developed in Fortran to compute all the mechanical properties and tested for various isotropic sections first and compared with the available results. The locations of mechanical centre of gravity and mechanical shear centre are given with respect to the fibre angle variation in composite beams. Variations of bending and torsional stiffness are shown to vary with respect to the fibre angle orientations.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.4
• /
• pp.1031-1038
• /
• 1994

Characteristics of pulsatile flow and heat transfer have been studied numerically in the constant heat flux curved tube with periodic pressure gradient. As the Womersley number increases, the phase difference between the pressure gradient and the cross section averaged axial velocity becomes larger. In case of the Womersley number $\beta = 2$, when cross section averaged axial velocity reaches periodic state with time, the reverse and the natural flow coexist at phase angle, $\lambda = 1.44\pi$ and $\lambda =1.96\pi$. For all the Womersley numbers of present investigation, the time variation of wall temperature near inner wall is higher than that of near outer wall, independent of phase angle.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.79-83
• /
• 1992

According to the variation of hydrostatic pressure on the central axis of deformable material, the V-shaped central bursting defect may be created on extrusion or drawing processes. The process factors whichaffect the generation of defects are die semi-angle, reduction ratio of cross-sectional area, friction factor, material properties and so on. The combination of these factors can determine the prossibility of defect creation and the shape of various round holes which have been created inside already. By the rigid plastic finite element method, this paper describes the observations of change in shape of a round hole with process conditions suchas die semi-angle, reduction ratio of cross-sectional area and friction factorat the unsteady state of axi-symmetrical extrusion process when the round hole is alreadyexisted inside the original billet, and also, the effects of process factors are investigated to prevent the possible defects.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.547-552
• /
• 2015

이번 연구에서는 Ali & Ramadhayni[2]에 의해 실험된 corrugated fin에 Cross-Cutting을 하여 압력강하를 2-D Laminar 영역에서 분석하였다. 분석 지표로는 Pressure drop의 무차원화된 지표인 friction factor를 사용하였고, corrugation angle을 $10^{\circ}$, $20^{\circ}$, $30^{\circ}$로 변화 시켜가며 진행하였다. Cross-Cutting의 길이는 $0.3D_h$길이로 고정시켜 계산하였고, 모든 값은 $D_h=2l$로 무차원화 하였다. Corrugated Fin의 경우, Corrugation Angle에 따라 층류영역에서 주기성을 가진 vortex shedding이 일어나는데, 그 때의 레이놀즈 수를 본 연구에서는 임계 레이놀즈 수라 하고, Vortex Shedding이 일어나기 시작하는 $Re_{cr}$ 이하에서 연구를 진행하였다.

• The Journal of the Korean dental association
• /
• v.51 no.10
• /
• pp.551-555
• /
• 2013

The purpose of this study was to give a guideline for selecting the nickel-titanium (NiTi) file by review from many studies. Since the early 1990s, several instrument systems manufactured from NiTi have been introduced into endodontic practice. The specific design characteristics vary, such as tip shape and size, cross sectional view, helix angle, and pitch space. Some of the early systems have been removed from the market or play only minor roles; others are still widely used. New designs continually are produced, but the extent to which clinical outcomes will depend on design characteristics is difficult to forecast. In this study, I have reviewed the different design characteristics in respect of the safety and efficiency. With the review from many studies, I concluded that the clinicians must be understand the specific design characteristics for selecting the ideal NiTi rotary instruments.

• Journal of the Korean Magnetic Resonance Society
• /
• v.16 no.2
• /
• pp.103-110
• /
• 2012

Membrane proteins play a essential role in the biological systems and it is not easy to handle a membrane protein for its structural study. Solid-state NMR (ssNMR) can be a good tool to investigate the structures and dynamics of membrane proteins. In ssNMR, Magic Angle Spinning (MAS) and Cross Polarization (CP) can be utilized to reduce the line-broadening, leading to high resolution and sensitivity in the spectrum. ssNMR, if combined with other spectroscopic methods, can provide us a enough knowledge on structures and dynamics of membrane proteins in biological condition.

• Cross-Cultural Studies
• /
• v.27
• /
• pp.225-253
• /
• 2012

Mikhail Vrubel' has written three Hamlet paintings in his extraordinary tragic lifetime. The first watercolor painting , which he has written in 1883, remained unfinished. He could not complete the second version of , which he painted in oil in the next year, neither. Finally, he has completed the third version of in 1888. As is generally known, is not widely known Vrubel's work. This work is mainly mentioned from the point of view that it is the first literary hero whom Vrubel' has created in his literatureoriented art world, and it is a presage of the Demon, Vrubel's central hero's advent. In this paper, we analyzed Vrubel's three from a different angle, nothing but from the angle of Russian Hamletism. For this, in the second chapter, we've researched Vrubel's main artistic credo. In the next chapter, we've analyzed Vrubel's three in detail from the view of Russian Hamletism.