Bolted joint connection is the most commonly used connection element in structures and devices. The loosening due to external dynamic loads cannot be observed and measured easily and may cause catastrophic loss especially in an extreme requirement and/or environment. In this paper, an innovative Real-time Cross-Correlation Method (RCCM) for monitoring of the bolted joint loosening was proposed. We apply time reversal process on stress wave propagation to obtain correlation signal. The correlation signal's peak amplitude represents the cross-correlation between the loosening state and the baseline working state; therefore, it can detect the state of loosening. Since the bolt states are uncorrelated with noise, the peak amplitude will not be affected by noise and disturbance while it increases SNR level and increases the measured signals' reliability. The correlation process is carried out online through physical wave propagation without any other post offline complicated analyses and calculations. We implemented the proposed RCCM on a single bolt/nut joint experimental device to quantitatively detect the loosening states successfully. After that we implemented the proposed method on a real large structure (reaction wall) with multiple bolted joint connections. Loosening indexes were built for both experiments to indicate the loosening states. Finally, we demonstrated the proposed method's great anti-noise and/or disturbance ability. In the instrumentation, we simply mounted Lead Zirconium Titanate (PZT) patches on the device/structure surface without any modifications of the bolted connection. The low-cost PZTs used as actuators and sensors for active sensing are easily extended to a sensing network for large scale bolted joint network monitoring.
Backgound: This study was performed to evaluate the incidences, the risk factors, and the clinical course of the hyperamylasemia in patients who underwent open heart surgery under cardiopulmonary bypass. Material and Method: Thirty seven patients who underwent cardiopulmonary bypass were studied at Department of Thoracic & Cardiovascular Surgery, Yeungnam University Hospital, from July 1997 to June 1998. The thirty seven patients were divided into two groups, 13 patients in group I had normal serum amylase levels and 24 patients in group II had hyperamylasemia. Result: Mean serum amylase(IU/l) levels and 24 patients in group II had hyperamylasemia. Result: Mean serum amylase(IU/l) levels of gorup II showed 54.3$\pm$4.6, 78.0$\pm$9.2, 372.0$\pm$103.4, 460.5$\pm$80.4, 280.4$\pm$46.6, and 131.0$\pm$15.6, preoperative, immediate postoperative, at postoperative 1, 2, 3, and 7 days, respectively. In group II, serum amylase level of the postoperative day 2 was the highest and was significantly higher than that of the preoperative day(p<0.001). Serum amylase level started to decreased at postoperative day 3 and returned to the normal level at postoperative day 7. Significant clinical symtoms of overt pancreatitis were not shown in patients in group II. The following perioperative variable such as diagnosis, cardiopulmonary bypass time, aortic cross clamping time, mean systemic pressure during bypass, and administration of steroid were compared between groups. There were no significant differences between groups. In all patients, Serum amylase level of postoperative day 2 and aortic cross clamping time were correlated significantly(p=0.047). Conclusion: Serum amylase level after cardiopulmonary bypass could be elevated postoperatively and serum amylase level of POD 2 was considered to have significant correlation with aortic cross clamping time. Shortening of aortic cross clamping time will help in reducing the hyperamylsemia. In this study, although significant clinical symptoms and overt pancreatitis were not seen from hyperamylsemic patients, careful clinical observation of hyperamylasemia would be necessary.
With regard to price elasticity and cross elasticity of electricity, optimal generation expansion planning method including load management effect is suggested. In addition, optimal peak time price can be determined simultaneously, and we adopt peak time tariff as load management strategy. Instead of using hourly marginal demand curves where we can get customer surplus, we used chronological load curve with constraints to preserve social welfare. This method is proved useful in short-term generation expansion planning.
This paper reports on the development of Micro optical cross connector(MOXC) performance evaluation system using DAQ board and Labview. The system is composed of optical part, driving circuit and software part, this evaluation system can measure insertion loss, response time and life time of MOXC, this system canbe used in mass production of MOXC.
In cardiac patients who received multidose cold blood potassium cardioplegia for intracardiac procedures, the intraoperative and the immediate postoperative blood potassium levels were decreased at aortic cross-clamp time below 2 hours and increased at aortic cross-clamp time above 2 hours, but they were within normal limit [not hypokalemia or hyperkalemia]. In spite of increased infusion numbers and amount of cold blood potassium cardioplegia, the postoperative blood potassium levels were similar to the postoperative levels, the immediate postoperative A-V blocks were transient and the postoperative arrhythmia were rare.
KSII Transactions on Internet and Information Systems (TIIS)
/
제11권10호
/
pp.4823-4843
/
2017
In this paper, an improved utility-based cross-layer dynamic subcarrier allocation (DSA) algorithm is proposed for single carrier frequency division multiple access (SC-FDMA) system, which adopts adaptive service rate control (ASRC) to eliminate the service rate waste and improve the spectral efficiency in heterogeneous network including non-real-time traffic and real-time traffic. In this algorithm, furthermore, a first in first out (FIFO) queuing model with finite space is established on the cross-layer scheduling framework. Simulation results indicate that by taking the service rate constraint as the necessary condition for optimality, the ASRC algorithm can effectively eliminate the service rate waste without compromising the scheduling performance. Moreover, the ASRC algorithm is able to further improve the quality of service (QoS) performance and transmission throughput by contributing an attractive performance trade-off between real-time and non-real-time applications.
Groundwater recharge characteristics in a fractured granite area, Mt. Geumjeong, Korea. was interpreted using bedrock groundwater and wet-land water data. Time series analysis using autocorreclation, cross-correlation and spectral density was conducted for characterizing water level variation and recharge rate in low water and high water seasons. Autocorrelation analysis using water levels resulted in short delay time with weak linearity and memory. Cross-correlation function from cross-correlation analysis was lower in the low water season than the high water season for the bedrock groundwater. The result of water level decline analysis identified groundwater recharge rate of about 11% in the study area.
This article presents an application of a large-scale structural mixing model(Broadwell et at. 1984) to the blowout of turbulent reacting cross flow jets. Experimental observations, therefore, aim to identify the existence of large-scale vortical structure exerting an important effect upon the flame stabilization. In the analysis of common stability curve, it is seen that the phenomenon of blowout are only related to the mixing time scale of the two flows. The most notable observation is that the blowout distance is traced at a fixed positions according to the velocity ratio at all times. Measurements of the lower blowout limits in the liftable flame are qualitatively in agreement with the blowout parameter $\xi$, proposed by Broadwell et al. Good agrement between the results calculated by a modified blowout parameter $\xi$'and the present experimental results confirms the important effect of large-scale structure in the stabilization feature of blowout.
수중에서 음원의 위치 추정을 위해 적용되어지는 기법으로써 시간지연차 (TDOA : Time Difference Of Arrival) 추정, 빔 형성 기법, 고 분해능 기법 등이 있다. 본 논문에서는 상대적으로 적은 수의 센서를 사용하여 주파수 영역에서 시간 지연차 추정에 사용되는 MCPSP (Modified Cross Power Spectrum Phase) 함수를 이용하였다. 그러나 MCPSP 함수에 기반한 방법은 CW (Continuous Wate) 신호를 대상으로 할 경우 추정 성능이 크게 떨어진다. 이에 본 논문에서는 Pulsed CW신호를 사용하는 수중 음원의 위치를 추정하기 위해 단 구간 (short-time) 에너지 검출을 이용하여 핑(ping)의 경계 영역을 포함하는 세그먼트를 구성하고 이로부터 MCPSP 함수를 구하는 방법을 제안하였다. 제안된 방법의 성능에 대한 이론적인 접근과 함께 다양한 환경 하에서 분석이 이루어졌다.
Metaphors were conceived of as a figure of speech whose role consisted in merely ornamenting the language. However, with their seminal book Metaphors we live by (1980), Lakoff and Johnson have revolutionized the conception of metaphors by placing them as central to human language, thought and action. Cognitive linguists argue that humans tend to conceptualize abstract concepts, such as time, through more experiential and tangible concepts. For instance, it has been observed that the abstract concept of time is conceptualized as space in several unrelated languages. According to the Conceptual Metaphor Theory (CMT), TIME AS SPACE metaphor covers two more specific metaphors: (1) The MOVING TIME metaphor wherein the observer is conceived as a stationary entity, as in The end of the academic year is getting closer; and (2) The TIME AS A LOCATION metaphor wherein times are conceived as stationary points and the observer is conceived as moving relative to these locations, as in We are first approaching the end of the year. This paper aims at probing the validity of the CMT representations of time on the basis of an analysis of time metaphors in two languages: English and French. This analysis is conducted within the framework of CMT. The results corroborate the CMT representations of time, suggesting that in both languages the abstract concept of time is expressed in spatial terms. In English, as in French, time is conceptualized as a moving entity and as having extension in space. In both languages, time can be seen as bounded; therefore, one can perform actions within defined limits of time.
이메일무단수집거부
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.