• Smart Structures and Systems
• /
• 제17권3호
• /
• pp.471-489
• /
• 2016

Modal identification based on ambient vibration data has attracted extensive attention in the past few decades. Since the excitation for ambient vibration tests is mainly from the environmental effects such as wind and traffic loading and no artificial excitation is applied, the signal to noise (s/n) ratio of the data acquired plays an important role in mode identifiability. Under ambient vibration conditions, certain modes may not be identifiable due to a low s/n ratio. This paper presents a study on the mode identifiability of an instrumented cable-stayed bridge with the use of acceleration response data measured by a long-term structural health monitoring system. A recently developed fast Bayesian FFT method is utilized to perform output-only modal identification. In addition to identifying the most probable values (MPVs) of modal parameters, the associated posterior uncertainties can be obtained by this method. Likewise, the power spectral density of modal force can be identified, and thus it is possible to obtain the modal s/n ratio. This provides an efficient way to investigate the mode identifiability. Three groups of data are utilized in this study: the first one is 10 data sets including six collected under normal wind conditions and four collected during typhoons; the second one is three data sets with wind speeds of about 7.5 m/s; and the third one is some blind data. The first two groups of data are used to perform ambient modal identification and help to estimate a critical value of the s/n ratio above which the deficient mode is identifiable, while the third group of data is used to perform verification. A couple of fundamental modes are identified, including the ones in the vertical and transverse directions respectively and coupled in both directions. The uncertainty and s/n ratio of the deficient mode are investigated and discussed. A critical value of the modal s/n ratio is suggested to evaluate the mode identifiability of the deficient mode. The work presented in this paper could provide a base for the vibration-based condition assessment in future.

• 한국해양공학회지
• /
• 제23권1호
• /
• pp.74-80
• /
• 2009

In this study, the static and modal analyses to find the characteristic of eigenvalues for a towed cable were with a free boundary condition at the bottom end carried out with numerical study. The resulting numerical code with finite element method was used to study sample problems for a cable with towing speeds. After tracing the equilibrium state with a towing speed through the static analysis, modal analysis on the basis of static results was performed. The static top tension for a critical towing speed is nearly 50 percent of what it was for a free hanging pipe. From static analyses, it is found that towing speed has a noticeable effect on top tension of a towed pipe. At a high towing speed, differences between the first and second periods become larger. Compared to the fundamental period for a free hanging pipe, that for a towed pipe with a critical towing speed is approximately 1.4 times larger. This result is very important point in that the lock in condition and tension of the towed cable system with top excitation can be predicted. The corrected close form solution to solve natural periods for a towed cable was presented in this study. The code is validated by comparison of the results of theoretical and numerical studies. Two results were in very good agreement. This study can contribute to predicting the lock-in condition and tension for a towed cable or pipe with top excitation.

• 대한기계학회논문집A
• /
• 제38권4호
• /
• pp.379-384
• /
• 2014

가스터빈엔진의 가장 핵심 부품인 디스크와 블레이드는 고온, 고압축비, 고속 회전이라는 가혹한 환경에서 지속적으로 운용된다. 이러한 가혹한 환경과 디스크와 블레이드가 가지는 큰 회전 에너지로 인해 디스크 및 블레이드에 의해 유발되는 파손은 항공기 손상 혹은 탑승자의 피해로 이어지는 재해적 고장 혹은 한계 고장으로 이어진다. 그러므로 디스크와 블레이드의 구조적 건전성의 마진을 충분히 확보하기 위해서 본 연구에서는 디스크의 취약 부위인 도브테일의 형상을 최적화하고, 그 해의 강건성을 확인하기 위해 치수 공차와 피로 수명의 산포와 같은 불확실성에 대하여 신뢰도 해석을 수행하고자 한다. 이 결과를 통해 결정론적 방법인 최적설계의 필요성과 함께 한계를 확인하고, 향후 신뢰도 기반 최적설계의 필요성을 인지하고자 한다. 이를 위해 비선형 열-구조 연성해석과 접촉 해석을 포함한 유한요소해석을 수행하였다.

• 한국추진공학회지
• /
• 제5권4호
• /
• pp.31-39
• /
• 2001

복합재료로 제작이 되는 수송기계용 추진축은 진동, 소음, 중량 등을 감소시킬 수 있는 장점을 가진다. 본 연구에서는 유한요소법을 이용하여 카본/에폭시 복합재료로 구성된 추진축을 설계하였으며 필라멘트 와인딩 방법을 사용하여 시험용 시편을 제작하였다. 유한요소법을 이용한 추진축의 설계 방법의 정확성을 확인하고자 FFT 해석기와 충격해머를 이용한 고유진동수 측정시험과 임계회전속도 측정 실험 장비를 이용한 임계회전속도 측정시험을 수행하였다. 해석결과와 시험결과를 비교하였을 때 오차율은 3.4%이하로 해석결과의 신뢰성을 확인하였다. 이러한 FEM 설계방법을 이용하여 추진 축의 진동 및 강도특성에 영향을 미치는 요인들에 대한 연구를 수행하였다 여러 요인들 중 중량의 증가 없이 고유진동수 변화에 가장 큰 영향을 미치는 것은 와인딩 각도임을 확인하였다.

• 항공우주기술
• /
• 제1권1호
• /
• pp.8-27
• /
• 2002

본 연구에서는 현재 개발중에 있는 복합재료 선미익 항공기의 날개에 작용하는 하중해석을 수행하였다. 중량, 공력계수, 구조설계속도, 하중 등을 계산하기 위해 사용된 Tool은 Excel에서 운용되는 Visual Basic 프로그램으로 계산에 많은 도움을 주었다. 하중해석에 기본적으로 요구되는 항공기의 형상치수, 부품의 종류 및 중량 그리고 좌표계 등은 Catia 모델링, 실제측정 또는 재료밀도 값 등을 이용해 구하였으며, 이들 자료를 통하여 항공기의 중량, 무게중심, 관성모멘트, 구조설계속도, 날개의 하중분포, 힘과 모멘트 등을 계산하였다. 또한 항공기의 날개 및 동체의 임계하중 조건을 선정하는데 필수적인 항공기의 V-n 선도를 도시하였으며, 이 V-n 선도는 항공기의 최대중량 2,573 파운드 및 해면고도조건에서 설계속도 $V_A$, $V_C$, $V_D$ 및 하중계수 +3.8G, -1.52G에 대한 비행범위를 제시하고 있다. 앞으로는 V-n 선도로부터 선정된 임계하중을 이용하여 해석된 동체 및 날개에 대한 하중을 제시하고자 한다.

• Wind and Structures
• /
• 제38권1호
• /
• pp.43-58
• /
• 2024

To ensure the flutter stability of three-tower suspension bridges under skew wind, by using the computational procedure of 3D refined flutter analysis of long-span bridges under skew wind, in which structural nonlinearity, the static wind action(also known as the aerostatic effect) and the full-mode coupling effect etc., are fully considered, the flutter stability of a three-tower suspension bridge-the Taizhou Bridge over the Yangtze River in completion and during the deck erection is numerically investigated under the constant uniform skew wind, and the influences of skew wind and aerostatic effects on the flutter stability of the bridge under the service and construction conditions are assessed. The results show that the flutter critical wind speeds of three-tower suspension bridge under service and construction conditions fluctuate with the increase of wind yaw angle instead of a monotonous cosine rule as the decomposition method proposed, and reach the minimum mostly in the case of skew wind. Both the skew wind and aerostatic effects significantly reduce the flutter stability of three-tower suspension bridge under the service and construction conditions, and the combined skew wind and aerostatic effects further deteriorate the flutter stability. Both the skew wind and aerostatic effects do not change the evolution of flutter stability of the bridge during the deck erection, and compared to the service condition, they lead to a greater decrease of flutter critical wind speed of the bridge during deck erection, and the influence of the combined skew wind and aerostatic effects is more prominent. Therefore, the skew wind and aerostatic effects must be considered accurately in the flutter analysis of three-tower suspension bridges.

• Advances in aircraft and spacecraft science
• /
• 제5권1호
• /
• pp.51-71
• /
• 2018

This work proposes a theoretical and numerical study on the behavior of a tapered shaft rotor made of composite materials by the classical version h and the version p of the finite element method. Hierarchical form functions are used to define the model. The purpose of this paper is to determine the expressions of the kinetic and potential energies of the tree necessary for the results of the equations of motion. A comparison between the version h and the p version of the finite element method of the functions of polynomial and trigonometric hierarchical forms with six degrees of freedom per node, of a composite tapered and cylindrical shaft which rotates at a constant speed about its axis. It is found that when the number of functions of form (the version p) is increased, the solution converges. It is also observed that the conicity of the shaft increases the rigidity with respect to a uniform shaft having the same mechanical properties. The numerical simulation allowed us to determine the natural frequencies and the critical speeds of the composite shaft systems are compared with those available in the literature and the effectiveness of the methods used are discussed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.133-133
• /
• 2009

It is desirable to choose a high-k material having a large band offset with the tunneling oxide and a deep trapping level for use as the charge trapping layer to achieve high PIE (Programming/erasing) speeds and good reliability, respectively. In this paper, charge trapping and tunneling characteristics of high-k hafnium oxide ($HfO_2$) layer with various thicknesses were investigated for applications of tunnel barrier engineered nonvolatile memory. A critical thickness of $HfO_2$ layer for suppressing the charge trapping and enhancing the tunneling sensitivity of tunnel barrier were developed. Also, the charge trap centroid and charge trap density were extracted by constant current stress (CCS) method. As a result, the optimization of $HfO_2$ thickness considerably improved the performances of non-volatile memory(NVM).

• 대한기계학회논문집A
• /
• 제25권12호
• /
• pp.2019-2029
• /
• 2001

Up to now a wide variety of researches on inpipe inspection robots have been introduced, but it still seems to be difficult to construct a robot providing mobility sufficient to navigate inside the complicated configuration of underground pipelines. This paper introduces a robot called MRINSPECT IV(Multifunctional Robotic Crawler for inpipe inSPECTion IV) for the inspection of urban gas pipelines with a nominal 4-inch inside diameter. The proposed robot can freely move along the basic configuration of pipelines such as along horizontal or vertical pipelines. Moreover it can travel along reducers, elbows, and steer in the branches by modulating the speeds of driving modules. Especially, its capability for steering in tile three-dimensional pipeline configuration has a competative edge over the other ones and provides excellent mobility in navigation. Its critical points in the design and construction are introduced and results of experiments are given.

• 소음진동
• /
• 제7권4호
• /
• pp.645-653
• /
• 1997

For high performance rotating machinery, unstable vibrations may occur caused by hydrodynamic forces such as oil film forces, clearance excitation forces generated by the working fluid, and etc. In order to improve the availability one has to take into account the vibrations very accurately. When designing a rotating machinery, the stability behavior and the resonance response can be obtained by calculation of the complex eigenvalues. A suitable modifications of seal and/or bearing design may effectively improve the stability and the response of a rotor system. This paper deals with the optimum length and clearance of seals and bearings to minimize the resonance response(Q factor) and to maximize the logarithmic decrement in the operating speed under the constraints of design variables. Also, for an avoidance of resonance region from the operating speed, an optimization technique has been used to yield the critical speeds as far from the operating speed as possible. The optimization method is used by the genetic algorithm, which is a search algorithm based on the mechanics of natural selection and natural genetics. The results show that the optimum design of seals and bearings can significantly improve the resonance and the stability of the pump rotor system.