• 대한간호학회지
• /
• 제44권2호
• /
• pp.129-138
• /
• 2014

Purpose: To develop a Critical Thinking Skill Test for Nursing Students. Methods: The construct concepts were drawn from a literature review and in-depth interviews with hospital nurses and surveys were conducted among students (n=607) from nursing colleges. The data were collected from September 13 to November 23, 2012 and analyzed using the SAS program, 9.2 version. The KR 20 coefficient for reliability, difficulty index, discrimination index, item-total correlation and known group technique for validity were performed. Results: Four domains and 27 skills were identified and 35 multiple choice items were developed. Thirty multiple choice items which had scores higher than .80 on the content validity index were selected for the pre test. From the analysis of the pre test data, a modified 30 items were selected for the main test. In the main test, the KR 20 coefficient was .70 and Corrected Item-Total Correlations range was .11-.38. There was a statistically significant difference between two academic systems (p=.001). Conclusion: The developed instrument is the first critical thinking skill test reflecting nursing perspectives in hospital settings and is expected to be utilized as a tool which contributes to improvement of the critical thinking ability of nursing students.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.292-295
• /
• 2008

In a SCWR (SuperCritical pressure Water cooled Reactor), the coolant temperature initially at below the pseudo-critical temperature at the bottom of a reactor core increases as the coolant flows upward through the sub-channels of the fuel assemblies, and it finally becomes higher than the pseudo-critical temperature when it leaves the reactor core. At certain conditions, heat transfer deterioration occurs near the pseudo-critical temperature and it may cause a drastic rise of the fuel surface temperature resulting a fuel failure. Therefore, an accurate estimation of the heat transfer coefficient is very important for the thermal-hydraulic design of a reactor core. An experiment on heat transfer to the vertically upward flowing $CO_2$ at a supercritical pressure in a circular tube were performed at KAERI. The internal diameter of the test section is 6.32 mm, which corresponds to the hydraulic diameter of a sub-channel in the conceptional design proposed by KAERI. The test range of the mass flux is 285 to 1200 kg/m$^2$s and the maximum heat flux is 170 kW/m$^2$. The inlet pressure is maintained at 8.12 MPa, which is 1.1 times the critical pressure. A new correlation, which covers both the normal and deterioration heat transfer regimes was proposed and compared with the estimations by exiting correlations.

• 설비공학논문집
• /
• 제20권9호
• /
• pp.571-580
• /
• 2008

In this work, pool boiling heat transfer coefficients(HTCs) of 5 refrigerants of differing vapor pressure are measured on horizontal smooth square surface of 9.52 mm length. Tested refrigerants are R123, R152a, R134a, R22, and R32 and HTCs are taken from $10\;kW/m^2$ to critical heat flux of each refrigerant. Wall and fluid temperatures are measured directly by thermocouples located underneath the test surface and by thermocouples in the liquid pool. Test results show that pool boiling HTCs of refrigerants increase as the heat flux and vapor pressure increase. This typical trend is maintained even at high heat fluxes above $200\;kW/m^2$. Zuber's prediction equation for critical heat flux is quite accurate showing a maximum deviation of 21% for all refrigerants tested. For all refrigerant data up to the critical heat flux, Stephan and Abdelsalam's well known correlation underpredicted the data with an average deviation of 21.3% while Cooper's correlation overpredicted the data with an average deviation of 14.2%. On the other hand, Gorenflo's and lung et al.'s correlation showed only 5.8% and 6.4% deviations respectively in the entire nucleate boiling range.

• 한국세라믹학회지
• /
• 제44권9호
• /
• pp.524-528
• /
• 2007

The results of evaluating steel corrosion in concrete containing chloride content of various levels indicated that the more chloride content in concrete leads to the lower potential and higher corrosion current density. However, the open circuit potential of steel varied with time and exposure condition, and the corelation between the open circuit potential and corrosion current density was not obvious. In order to determine the critical threshold content of chloride of steel corrosion in concrete, the concept of average corrosion current density was employed. The range of critical chloride content in portland cement concretes was about $1.56{\sim}1.77%$($Cl^-$, %, wt of cement content) along with water-cement ratio, and higher water-cement ratio resulted in reduction in critical threshold chloride content.

• 한국분무공학회지
• /
• 제3권4호
• /
• pp.1-7
• /
• 1998

The measurement of breakup length of viscous liquid jet in stagnant air was conducted by a 3CCD digital video camera. The nozzle diameters of 4, 6, 8mm with L/d=50 were selected and the dynamic viscosity of viscous liquid made of glycerine and water was in the range of $1.061\times10^{-6}m^2/s$ to $4.935\times10^{-5}m^2/s$. The critical velocity is decreased and the breakup length is increased with the increase of nozzle diameter at the same dynamic viscosity of liquid. At the same nozzle diameter, the breakup length and the critical velocity are both increased with the increase of dynamic viscosity of liquid. It is found in the theoretical analysis that the initial disturbance level is the main cause of occurrance of critical Reynolds number in the stability curve. The comparison of experimental critical Reynolds number and the empirical correlation by Tanasawa and Toyota reveals the relatively good agreement.

• Journal of Power Electronics
• /
• 제10권2호
• /
• pp.132-137
• /
• 2010

Interleaving techniques are widely used to reduce input/output ripples and to increase the power capacity of boost converters operating in critical conduction mode. Two types of phase-shift control schemes are studied in this paper, the turn-on time shifting method and the turn-off time shifting method. It is found that although the turn-off time shifting method exhibits better performance, it suffers from sub-harmonic oscillations at high input voltages. To solve this problem, an intensive quantitative analysis of the sub-harmonic oscillation phenomenon is made in this paper. Based upon that, a novel modified turn off time shifting control scheme for interleaved boost converters operating in critical conduction mode is proposed. An important advantage of this scheme is that both the master phase and the slave phase can operate stably in critical conduction mode without any oscillations in the full input voltage range. This method is implemented with a FPGA based digital PWM control platform, and tests were carried out on a two-phase interleaved boost PFC converter prototype. Experimental results demonstrated the feasibility and performance of the proposed phase-shift control scheme.

• Nuclear Engineering and Technology
• /
• 제34권4호
• /
• pp.382-395
• /
• 2002

An experimental study on transient critical heat flux (CHF) under flow coastdown has been performed for the water flow in a non-uniformly heated vertical annulus under low flow and a wide range of pressure conditions. The objectives of this study are to systematically investigate the effect of the flow transient on the CHF and to compare the transient CHF with steady-state CHF The transient CHF experiments have been performed for three kinds of flow transient modes based on the coastdown data of a nuclear power plant reactor coolant pump. At the same inlet subcooling, system pressure and heat flux, the effect of the initial mass flux on the critical mass flux can be negligible. However, the effect of the initial mass flux on the time-to- CHF becomes large as the heat flux decreases. The critical mass flux has the largest value for slow flow reduction rate. There is a pressure effect on the ratio of the transient CHF data to steady-state CHF data. Except under low system pressure conditions, the flow transient CHF was revealed to be conservative compared with the steady-state CHF data. Bowling CHF correlation and thermal hydraulic system code MARS show promising results for the prediction of CHF occurrence .

• 한국안전학회지
• /
• 제3권2호
• /
• pp.35-48
• /
• 1988

Modern technological progress demands the use of materials at high temperature and high pressure. One of the most critical factors in considering such applications - perhaps the most critical one - is creep behavior. In this study the stress exponents n were determined during creep over the temperature range of $90^{\circ}C\;to\;500^{\circ}C$ (0.4 - 0.85 Tm) and stress range of 0.64 kgt/$mm^2$ in order to investigate the creep hehavior. The stress dependence of rapture time (n') were determined over the temperature range of $200^{\circ}C\;to\;240^{\circ}C$ and stress range of 8.13 kgt/$mm^2$ to 9.55 kgt/$mm^2$ in order to investigate to creep rupture property. And the stress transient dip tests were also carried out for the internal stress ${\sigma}i$ over the temperature range of $90^{\circ}C\;to\;500^{\circ}C$ and stress range of 0.64kgt/$mm^2$ to 17.2 kgt/$mm^2$. The creep tests for constant temperature and stress transient dip tests were conducted in air with Al 7075 alloy under constant tensile load. At around the temperature range $200^[\circ}C\;-\;230^{\circ}C$ and the stress level 8.13 - 9.55 (kgt/$mm^2$), the temperature range $280^{\circ}C\;-\;310^{\circ}C$ and the stress level 1.85 - 2.55 (kgt/$mm^2$), the temperature range $380^{\circ}C\;-\;410^{\circ}C$ and the stress 1.53 - 0.91 (kgt/$mm^2$), the stress exponent in had the value of 6.2 - 6.65 but at around the temperature range $90^{\circ}C\;-\;120^{\circ}C$ and the stress level 10 - 17.2(kgt/$mm^2$), the value of 1.3, and at around the temperature range $470^{\circ}C\;-\;500^{\circ}C$, the stress level 0.62 - 1.02 (kgt/$mm^2$) the value of 1-1. Besides these results, at around the temperature $200^{\circ}C\;-\;240^{\circ}C$ the stress dependence of rupture time (n') had the value of 6.3. Finally, it was found that the value n calculated by considering the applied stress dependence of the internal stress were in good agreement with those obtained for the creep test. Then, it was concluded that the change in n was mainly attributed to the difference of the applied stress dependence of the internal stress and the ratio of the internal stress to the applied stress, and the creep rupture life may be represented as.

• Tuberculosis and Respiratory Diseases
• /
• 제80권1호
• /
• pp.27-34
• /
• 2017

Background: A sputum culture is the most reliable indicator of the infectiousness of pulmonary tuberculosis (PTB); however, a spontaneous sputum specimen may not be suitable. The aim of this study was to evaluate the infectious period in patients with non-drug-resistant (DR) PTB receiving adequate standard chemotherapy, using induced sputum (IS) specimens. Methods: We evaluated the duration of infectiousness of PTB using a retrospective cohort design. Results: Among the 35 patients with PTB, 22 were smear-positive. The rates of IS culture positivity from baseline to the sixth week of anti-tuberculosis medication in the smear-positive PTB group were 100%, 100%, 91%, 73%, 36%, and 18%, respectively. For smear-positive PTB cases, the median time of conversion to culture negativity was 35.0 days (range, 28.0-42.0 days). In the smear-negative PTB group (n=13), the weekly rates of positive IS culture were 100%, 77%, 39%, 8%, 0%, and 0%, respectively, and the median time to conversion to culture-negative was 21.0 days (range, 17.5-28.0 days). Conclusion: The infectiousness of PTB, under adequate therapy, may persist longer than previously reported, even in patients with non-DR PTB.

• Tuberculosis and Respiratory Diseases
• /
• 제66권6호
• /
• pp.431-436
• /
• 2009

Background: In order to access the role of ballooning in patients with post-tuberculosis bronchial stenosis (PTBS), medical records of patients who underwent the procedure were reviewed. Methods: Twenty-nine PTBS patients underwent balloon dilatation between May 1999 and November 2000 at Samsung Medical Center. The median age was 28 (range 16~62 year) and most patients were female (n=27, 93%). The mean number of ballooning procedures was 2.4 (range 1~8) and the interval between ballooning procedures was 76.2$\pm$69.7 days. Results: In general, the $FEV_1$ was improved after ballooning (from 66.2.$\pm$11.9% predicted to 73.5$\pm$13.0% predicted, p=0.0004). Among 29 patients who underwent ballooning, a clinically successful outcome was observed in 16 patients (55%). Comparison between the successful and unsuccessful groups showed that favorable factors for a successful outcome were a higher pre-9ballooning $FEV_1$ (71.1$\pm$8.1 vs. 60.2$\pm$13.3% predicted), higher post-9ballooning $FEV_1$ (89.2$\pm$7.8 vs. 63.4$\pm$9.2% predicted) and absence of left upper lobe collapse. The clinical outcome was unsuccessful in all eight patients with a pre-9ballooning $FEV_1$ $\leq$57% of predicted or with complete left upper lobe collapse. Conclusion: In conclusion, ballooning appears to be helpful in patients with PTBS, especially when the pre-ballooning $FEV_1$ >57% of predicted and there is no complete left upper lobe lung collapse.